浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

主动铰接盾构在连续小半径曲线中风化泥岩的掘进控制技术

武汉市轨道交通11号线东段工程光谷四路站—光谷五路站区间为"S"型连续曲线,最小平曲线半径为350 m,采用盾构法施工。通过对主动铰接盾构机掘进控制的难点分析,从土压力、千斤顶推力、千斤顶行程差、水平铰接角度和前盾水平趋向等方面采取有针对性的技术控制措施,使成型隧道轴线、管片错台控制在规范允许范围之内,成功解决了连续小半径曲线隧道盾构施工轴线难以控制、管片容易错台等大问题。     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

4缸柴油机停缸仿真及试验研究

采用停缸技术对小型4缸柴油机的燃油消耗率和排放进行了仿真和试验研究。利用GT-Power建立模型并模拟了停缸位置对燃油消耗率的影响,结合传热损失等因素确定了试验停缸位置。在断油式停缸和断油断气式停缸模式下进行试验和燃烧分析。试验结果表明:停缸后缸内等容度降低;断油式停缸后燃油消耗率和NOx增大但炭烟减少;断油断气式停缸后部分试验点燃油消耗率降低,但NOx和炭烟排放增加。     

刀豆蛋白A条件化培养基对体外培养的兔角膜内皮细胞生长的影响

目的研究刀豆蛋白A(concanavalin A,ConA)条件化培养基对体外培养的兔角膜内皮细胞(rabbit corneal endothelial cells,RCECs)生长的影响。方法采用揭取后弹力层及内皮细胞联合组织块法进行RCECs的体外原代培养,分别用含有体积分数为5%、10%、15%、20%ConA的活化大鼠脾细胞条件上清液的RPMI1640培养基进行RCECs原代培养,并用含10%(体积分数)胎牛血清(fetal bovine serum,FBS)的RPMI1640培养基作为对照。神经烯醇化酶免疫组织化学染色法进行细胞鉴定;噻唑蓝比色法观察各组RCECs生长的状况;SPSS11.0One-way ANOVA及LSD检验进行统计分析。结果成功进行了RCECs的体外培养,培养细胞内神经烯醇化酶阳性表达。ConA条件化培养基各组细胞增殖均高于对照组(P<0.001),且10%、15%ConA条件化培养基组的RCECs细胞数量明显高于其他各实验组(P<0.001)。结论ConA条件化培养基具有促进RCECs生长的作用,可作为培养辅佐剂。     

基于虚拟应力场法的船舶避让与控制

为了实现船舶在航道内的避障,应用虚拟力场法建立了避障模型,描述了目标点的虚拟引力和障碍物的虚拟斥力之间的关系及其功能设计,实现了从船舶运动坐标值到控制量的转变,结果证明．船舶能够在多变的周边环境中实现避障功能。     

大倾角搁浅船舶扳正过程分析

在研究大倾角搁浅船舶的扳正过程中,计算了难船扳正力、横倾角和吃水。根据搁浅船舶的受力特点,建立了其力学模型,分析了扳正过程中横倾角、吃水、入泥深度与海底泥土性质对船体的影响。利用GHS软件模拟搁浅船舶的扳正过程,以某搁浅液化气船舶为例,求解了其扳正过程中船体扳正力、总搁坐力、剪力、弯矩和转矩,比较了难船不同扳正方案,分析了难船的扳正方式、搁坐位置、上层建筑与储气罐对难船打捞的影响。分析结果表明:在扳正过程中,3个方案的力学参数的变化趋势是一致的。最大扳正力相差较大,差值为9.1%~20.0%。搁坐力、剪力和弯矩均在横倾角为-55°~-50°时达到最大值,船体虽然在该阶段不需加载较大的扳正力,但仍应该注意船体的受力情况。在横倾角为-120°~-100°时,转矩变化非常剧烈。弯矩和转矩均出现了反向变化的现象,威胁船体结构的安全,扳正中应该谨慎处理。选择合适的扳正方案时应该综合考虑扳正力施力点的位置和扳正过程对船体与环境安全的潜在威胁。     

机动车交通流比功率与能耗模型研究

为研究机动车交通流能耗,将机动车交通流比功率(VSP)作为研究对象.从最常见的单车比功率研究出发,使用气体动力学交通流模型联系单车比功率与交通流整体比功率,以此建立交通流比功率模型.为使此模型具备更显著的物理意义,将交通流比功率分为两部分,一部分为平衡交通流状态下的比功率,另一部分为偏离平衡交通流状态导致的比功率变化量,模型中的交通流参数与变量能够通过现有的交通流探测设备获取.将比功率理论模型从单车扩展到了交通流,用数学公式反应了交通流状态与比功率的关系,并且证明了交通流比功率能够通过交通流参数进行估计.并由交通流比功率出发,推导出交通流比功公式.此外研究了平衡态交通流比功率及比功与密度的关系.为研究机动车交通流能耗探索了新的思路.     

三轴船舶电动摇摆模拟试验台研究

针对船舶摇摆模拟试验台系统在科学研究和船载仪器可靠性试验中的应用,设计了一种多功能三轴船舶电动摇摆试验台随动控制系统。首先对摇摆试验台进行控制建模,确定电流、速度、位置三闭环控制方案,然后采用常规PID算法设计三环控制器参数,对位置环用模糊自适应PID控制器进行优化设计。提出以变周期、变幅度和组合曲线给定的摇摆方法模拟风、浪、流干扰,对系统进行仿真研究。仿真试验结果表明,设计的系统具有响应迅速、模拟准确、可靠等特点,能够较好的模拟实际海况中船舶摇摆运动,为搭建实际试验平台奠定了基础。