济南绿色地铁技术探索与应用

济南轨道交通将"绿色地铁"作为建设理念,采用近40项节能、节地、节水、节材、环境保护的技术措施。以1号线为例,详细介绍高架站下方设置设备用房、主变电所资源共享等节地技术,可节约土地约2.8万m2;高架车站采用清水混凝土施工技术、预制叠合结构体系等节材技术,可节省费用3 000万元,节省混凝土使用量43%;采用可调通风型站台门系统等节能技术,每座车站每年可节约电费约100万元;采用高架站台光伏发电、非晶合金配电变压器、再生能量吸收等技术,每年可节电774.03万k W·h。     

土基压应变敏感性分析

路表弯沉并不能完全反映土基顶面压应变,在路面结构设计中必需要重视土基顶面压应变的状态。鉴于此,采用典型路面结构,分析各结构层参数的变化对土基顶面压应变和土基内部压应变的影响,以为沥青路面结构设计提供参考。     

基于时间累计法的机车维修性预计分析

基于时间累积法,阐述机车维修性预计工作流程以及系统与LRU平均修复时间的计算方法。并以空调与通风系统为例,说明了系统及LRU平均修复时间的计算过程,并由此得出整车的平均修复时间。文章最后阐述了维修性预计对机车设计的指导作用以及使用时间累积法的局限性。     

城镇污水处理厂电气设计节能优化解析

从污水处理厂的供配电系统、电气设备选型、电气线路选型、照明系统四个方面介绍了城镇污水处理厂的电气设计节能优化的措施，并结合相关规范、文献及设计经验对污水厂电气设计节能优化要点进行简要解析。     

Residual stress measurement in an extra thick multi-pass weld using initial stress integrated inherent strain method

Residual stresses existing in a multi-pass butt joint with a thickness of 70 mm, using a flux-cored arc welding process, were measured by an inherent strain method (ISM). Since such a thick plate before welding contains a large amount of initial residual stresses (−300 to +100 MPa), the initial stresses were integrated with conventional ISM in order to determine the total residual stresses in a welded joint. Two methods named as initial stress integrated ISM and initial inherent strain integrated ISM were suggested for the consideration of the initial stress distributions through the thickness of base plates. The results show that there is a significant difference between the integrated ISM with initial stresses or initial inherent strain and the conventional ISM without initial stresses. The residual stresses measured by any of the initial stress integrated ISM and initial inherent strain integrated ISM agreed well with the neutron diffraction measurement. Thus, the proposed initial stress integrated ISM is a proper destructive measurement method in the case of thick weld joints.     

高速齿轮润滑极压添加剂的定量选用准则

根据边界反应膜分解失效机理和化学反应动力学理论，对边界膜的失效过程作了定量数学描述，提出了反映膜分离率的概念，据此确定了添加剂的温度，速度和活化能等三个定量选用准则。     

隧道数字化火灾预警系统的在线量化评估

为检查和评价隧道及地下空间火灾预警系统的实际功能,需要一套可行的在线评估手段。根据近年来国内外全尺寸隧道火灾发展曲线的试验结果,提出隧道火情的定义依据;引用运营隧道内准分布式光纤光栅感温火灾探测器的实测数据,证明运营中隧道报警系统的个性化现象;提出合格的数字化报警系统应存在一个在统计学意义上使漏报率和误报率同时达到期望值的合理阈值取值区间;建议以该区间的尺度作为该系统功能完好性的评估指标;对日常隧道运行温度数据的统计分析可估计合理阈值取值区间的下限,对规定条件下的现场点火试验温度数据分析可估计合理阈值取值区间的上限。在隧道运营期该区间尺度可实时在线自动更新。     

Prioritizing new bicycle facilities to improve low-stress network connectivity

This paper introduces a new method to prioritize bicycle improvement projects based on accessibility to important destinations, such as grocery stores, banks, and restaurants. Central to the method is a new way to classify “bicycling stress” using marginal rates of substitution which are commonly developed through empirical behavioral research on bicyclist route choice. MRS values are input parameters representing bicycling stress associated with the number of lanes and speed limit of a street. The method was programmed as a geographic information system tool and requires commonly available data. The tool is demonstrated on three improvement scenarios that were recently proposed for Seattle, Washington. The full build-out scenario consists of 771 projects that include various new bike lanes, protected bike lanes, and multi-use trails. The tool produces priority rankings based on a project’s ability to improve low-stress connectivity between homes and important destinations. The analysis identifies specific areas and neighborhoods that can be expected to exhibit better bikeability. Transportation planners can use the tool to help communicate anticipated project impacts to decision-makers and the public.     

Performance comparison between pedestrian push-button and pre-timed pedestrian crossings at midblock: a Korean case study

Walking has been highlighted as an independent transportation mode as well as an access/egress mode to/from public transit to encourage the use of more sustainable transport systems. However, walking does not seem to have priority over other transportation modes, especially in areas where various modes of movement are in conflict. The pedestrian push-button system seems to be a solution to distribute the right of way. The focus of this study is on the performance issue of the pedestrian push-button. Specifically, this study deals with issues related to mid-block crossings and attempts to answer two questions: whose waiting time is longer at pre-timed and push-button crossings, pedestrians, or vehicles? and which system – pre-timed or push-button – is better in terms of total waiting time? According to our simulation analyses, if the pedestrian flow rate is less than 120, 85, and 70 ped/h for two-, three-, and four-lane roads, respectively, the push-button system is recommended.     

Weight threshold estimation of falling UAVs (Unmanned Aerial Vehicles) based on impact energy

Different weight thresholds for drone operations have been specified by regulatory agencies in different countries, without detailed backgrounds of guidelines. Therefore, this paper aims to study weight thresholds by focusing different levels of injuries caused by the impact of the drones on human head of different weights dropped at various heights. The work covers drone free drop modelling, FEM (finite element method) based impact modeling, and comparable drop impact experiments. The analyses and experiments were conducted accordingly to two individual commercially-available groups: small and large drones in weights. Two well-established indicators defining head injuries due to impact, which are known as Head Injury Criterion (HIC) and Abbreviated Injury Scale (AIS), are used in the present weight threshold study. The proposed AIS level for the weight threshold estimation has been set at AIS level 3, which indicates major skull fracture, in the further analysis through the probability of fatality. The main focus of the present work is to perform a parametric study and to present a reliable model to estimate the weight thresholds of the drone operations based on HIC and AIS. In conclusion, the results obtained and presented in this paper have demonstrated and provided a comprehensive analysis of possible direct injuries of a falling drone impacting a human head, with relevant data of impact or injury levels associated with HIC and AIS obtained for a drone with different weights falling from various heights.