聚丙烯纤维混凝土直接拉伸性能的试验研究

重点研究聚丙烯纤维增强混凝土在单轴直接拉伸荷载下的力学性能和纤维混凝土的单轴拉伸应力变形全曲线。提出单轴拉伸相对应力裂缝宽度曲线的理论方程式。由单轴拉伸全曲线得到了纤维混凝土的应力裂缝宽度曲线、断裂能及特征长度等。试验发现:当纤维体积掺量为0 14%时,纤维混凝土的轴心抗拉强度比基准混凝土提高20%,极限拉伸应变提高49%,断裂能提高68%,临界断裂时的最大裂缝宽度增加55%。聚丙烯纤维具有良好的阻裂性能,增强了硬化混凝土的能量吸收能力。     

石灰土中石灰活性衰减规律研究

通过试验的方法研究松散石灰土在常温和低温开放状态、常温密封状态条件下石灰活性衰减的规律，推定出不同状态条件下石灰活性衰减率公式，以确定石灰土合理的闷料时间，减少不必要的石灰活性衰减和未消解石灰对路面基层的破坏，为石灰土路面基层质量问题的界定提供依据。     

大直径钢管桩承载力恢复过程试验研究

针对目前预制桩承载力恢复特性研究与工程应用中的不足,依托西非某海工工程,提出高应变法。采用对同一钢管桩进行初打与不同休止时间复打相结合的试验方法,研究了大直径钢管桩沉桩后的承载力恢复过程。结合地质情况、沉桩与试验结果,得到了钢管桩承载力、侧阻力及端阻力随时间变化的一般规律及影响因素,并通过静载试验对研究结果进行了验证。该研究在提高项目施工效率、降低成本的同时,还得到了有意义的规律与结论,可为后续类似项目提供参考。     

电动汽车充电桩安全管理研究

随着国家对环境保护和能源节约的重视以及新能源政策的实施,电动汽车行业迎来了快速发展。充电基础设施的建设,是加快电动汽车推广的重要需要。电动汽车充电基础设施建设和运营业务发展的机会也极大,随之而来的安全管理工作要求也越来越高。本文依据充电桩建设和运营的特点,剖析其中面临的安全风险,并提出加强安全管理工作的措施,为充电桩企业安全管理运营提供参考和借鉴。     

Experimental investigation of evaporation rate and exhaust emissions of diesel engine fuelled with cotton seed methyl ester and its blend with petro-diesel

An experimental study to measure the evaporation rates, engine performance and emission characteristics of cotton seed biodiesel (cotton seed oil methyl ester) and its blends in different volumetric proportions with diesel is presented. The thermo-physical properties of all the fuel blends have been measured and presented. Evaporation rates of neat cotton seed biodiesel, neat diesel and their bends have been measured under slow convective environment of air flowing with a constant temperature. Evaporation constants have been determined by using the droplet regression rate data. The neat fuels and fuel blends have been utilized in a test engine with different load conditions to evaluate the performance, combustion and emission characteristics of the fuels. The specific fuel consumption values of the two blends, viz. B25 and B75 are found to be same. At the highest load, B0 records the lowest CO volume followed by B100. From the observed evaporation, performance and emissions characteristics, it is suggested that a blend of B50 and B75 can be optimally used in standard diesel engine settings.     

桥梁模板施工技术应用性研究

桥梁模板是桥梁施工中的重要工具。通过搜集国内外桥梁模板资料,研究总结并提出解决模板工程在桥梁施工中存在各种问题的办法,将对提高工程质量、加快施工速度、提高劳动生产率、降低工程成本和实现桥梁工程的文明施工起到一定的推动作用。     

深圳地铁永磁同步牵引系统研究分析

牵引传动系统是轨道交通车辆装备实现机电能量转换的“心脏”单元,其性能在某种程度上决定轨道交通车辆的动力品质、能耗和控制特性,是轨道交通车辆节能升级的关键系统。而永磁同步牵引系统以其高效率、高可靠性和低能耗的优势特点,受到轨道交通行业的密切关注。文章阐述深圳地铁10号线永磁同步牵引系统批量装车概况,重点分析永磁同步牵引系统组成及优势,指出推广应用永磁同步牵引系统的经济和社会效益显著。     

基于生长曲线函数的货车运营环节碳达峰研究

货车是我国大气环境污染的重要来源之一，也是影响我国碳达峰总体目标实现的重要因 素。本文从货车运营环节入手，在运用生长曲线函数对货车保有量进行预测的基础上，对不同类 型货车的保有量和单车碳排放变化进行研究，并从货车节能技术发展、新能源货车推广和应用进 程两方面入手，分3种情景对货车运营环节中产生的碳排放总量趋势进行预判，推演货车运营环 节的碳达峰时间。研究结果表明，只有同时加快货车节能技术发展以及新能源货车推广和应用 进程，货车运营环节中产生的碳排放总量规模才能得到有效抑制并逐渐减少。若到 2030 年货 车单车燃料消耗水平较 2019 年降低 20%以上，新能源货车在货车整体保有量中的占比达到 20%，到 2060 年货车单车燃料消耗水平较 2019 年降低 50%，新能源货车占比达到 50%，则货车 运营环节碳达峰时间将缩短至2030年左右实现，2030年后货车运营环节产生的碳排放总量规 模将逐渐减少。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

A comparative life-cycle energy and emissions analysis for intercity passenger transportation in the U.S. by aviation,intercity bus,and automobile

Intercity passenger trips constitute a significant source of energy consumption, greenhouse gas emissions, and criteria pollutant emissions. The most commonly used city-to-city modes in the United States include aircraft, intercity bus, and automobile. This study applies state-of-the-practice models to assess life-cycle fuel consumption and pollutant emissions for intercity trips via aircraft, intercity bus, and automobile. The analyses compare the fuel and emissions impacts of different travel mode scenarios for intercity trips ranging from 200 to 1600 km. Because these modes operate differently with respect to engine technology, fuel type, and vehicle capacity, the modeling techniques and modeling boundaries vary significantly across modes. For aviation systems, much of the energy and emissions are associated with auxiliary equipment activities, infrastructure power supply, and terminal activities, in addition to the vehicle operations between origin/destination. Furthermore, one should not ignore the embodied energy and initial emissions from the manufacturing of the vehicles, and the construction of airports, bus stations, highways and parking lots. Passenger loading factors and travel distances also significantly influence fuel and emissions results on a per-traveler basis. The results show intercity bus is generally the most fuel-efficient mode and produced the lowest per-passenger-trip emissions for the entire range of trip distances examined. Aviation is not a fuel-efficient mode for short trips (<500 km), primarily due to the large energy impacts associated with takeoff and landing, and to some extent from the emissions of ground support equipment associated with any trip distance. However, aviation is more energy efficient and produces less emissions per-passenger-trip than low-occupancy automobiles for trip distances longer than 700–800 km. This study will help inform policy makers and transportation system operators about how differently each intercity system perform across all activities, and provides a basis for future policies designed to encourage mode shifts by range of service. The estimation procedures used in this study can serve as a reference for future analyses of transportation scenarios.