拱架式预切槽施工机械在黄土隧道施工中的应用

隧道预切槽施工技术在国外应用比较广泛,但在我国应用还较少。针对黄土地质专项研制了国内首台拱架式预切槽机,并在黄土隧道进行了施工试验。通过施工试验,掌握设备定位、分区切灌、设备行走、施工作业组织等关键技术,并提出应用改进及优化措施。试验结果表明切槽系统工作状态和设备切削、喷灌功能满足设计及施工试验要求,为预切槽同步切削喷灌一体化研究提供了数据支撑和研究方向。     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

高校图书馆的人力资源管理略论

文章分析了当前高校图书馆人力资源管理存在的问题,对加强人力资源管理的必要性提出了看法,并就加强人力资源管理的有效途径进行了探讨。     

桥梁加宽中新增梁对旧桥的影响

依托黄土地区高速公路改扩建桥梁加宽工程,选取一座3孔13 m简支空心板桥,分析新增空心板梁对旧桥原有板梁的影响。基于不同加宽方案对新旧桥空心板梁横向分布系数进行了计算,计算结果表明增加新梁截面刚度可有效降低旧梁横向分布系数。建议采用移旧桥边梁为新桥边梁并且提高新增空心板梁刚度的加宽方案。     

自锚式斜拉-悬索协作体系桥静风响应分析

自锚式斜拉-悬索协作体系桥作为一种全新的结构体系,兼备了自锚式悬索桥和斜拉桥的许多优点,结构体系则更为复杂。结合400m主跨的金州海湾大桥这一实际工程方案,建立了有限元空间分析模型,分析了其在静风荷载作用下的非线性行为,总结了初始攻角、附加攻角等参数及是否考虑缆索系统承受风荷载等对体系的影响规律。     

六五式铁路军用桥墩模拟拼装系统研制与开发

为了满足六五式铁路军用桥墩拼装演练的要求,介绍了“六五式铁路军用桥墩模拟拼装系统”的研制与开发工作。该系统不仅可以解决实际拼装作业的标准化和规范化问题,探索出安全、经济、高效、规范的拼装技术作业程序;而且可以降低拼装演练的费用,提高拼装作业人员的拼装技术水平,减小拼装时间,提高拼装效率。对培训专业保障队伍和保障战时铁路运输的畅通,具有一定的作用。     

新加坡公共交通发展经验及启示

通过实际考察和走访咨询,系统地总结了新加坡的公共交通发展经验。首先介绍了新加坡对小汽车和公共交通发展采取的＂推、拉策略＂,以及新加坡公共交通的发展历程。在此基础上,对新加坡公共交通发展的成功经验进行了归纳和总结,包括管理机制、公共交通设施建设、公共交通运营系统、政策法规等方面的内容。结合我国城市交通发展的现状和特点,对城市公共交通的发展提出了措施和建议。     

山区高速公路涵洞设计施工问题的探讨

对朝赤高速公路涵洞设计及施工过程中的一些关键技术问题进行探讨.