基于FLUENT的硅油减振器热片散热性能分析

散热片的散热性能好坏严重影响硅油减振器的使用寿命.利用计算流体力学软件FLUENT,建立了硅油减振器散热片的三维模型,模型中将热场与流场进行了耦合;通过对散热片表面的温度分布特性、空气流动特性和散热率进行数值模拟,研究分析了散热片不同结构型式对其散热性能的影响.本文的分析方法可用于指导硅油减振器散热片的设计和选型.     

废旧塑料改性沥青储存稳定性试验

以4类废旧塑料改性剂与分别经过裂化处理的加工塑料改性剂,采用合理的制备工艺对90#与70#基质沥青进行改性,并采用优化的离析试验分析方法对不同类型废旧塑料改性沥青展开研究,最后基于热分析试验对作用机理进行分析.结果表明:经裂化处理的加工废旧塑料改性沥青的储存稳定性相比原塑料改性沥青得到明显改善;4种通过裂化处理的加工废...     

热力隧道在非降水施工中的力学特性监测

城市热力供水工程逐渐由近地层明挖向深地层暗挖转移,通过对北京市两个典型地质热力隧道的现场原位的监测,分析浅埋暗挖热力隧道在非降水施工过程中对于砂卵石地质和粉质黏土地质条件下的初支结构内力、围岩性状、水文特征的变化及对地层的影响.试验监测结果表明,隧道围岩的土压力分布不同,水压力分布相同,初衬钢筋内力分布不同,砂卵石地质条件下的隧道初衬受力情况较好,隧道开挖对地表沉降影响较小,研究结果可在开挖城市供热、供水及供气等小断面隧道时参考.     

基于热分析与低温光谱的沥青热可逆老化机理

为了研究沥青胶结料在恒定低温储存过程中产生的热可逆老化机理,运用调制式差示扫描量热分析(MDSC)和低温红外光谱(LT-FTIR)技术对沥青胶结料热信号与红外光谱的热历史依赖性进行了试验分析,以确定2种不同分子量的线性饱和链烃(C₂₀H₄₂和C₃₂H₆₆)对热可逆老化的贡献。研究结果表明:沥青恒定低温硬化并非所有沥青的固有特性,存在不受恒定低温热历史影响的沥青胶结料;低分子量的饱和长链烷烃(石蜡)因其与沥青具有较好的相容性,会通过扩散的方式随着恒定低温时间的延长逐渐从沥青基体中析出,从而导致沥青的恒温硬化现象;由于高分子量的饱和长链烷烃与研究采用的沥青在相同条件下相容性差,其石蜡与沥青的二相分离结构并没有随着恒定低温时间的延长产生明显的变化。与热分析相比,低温红外光谱技术可在较低的降温速率下直接用于测试固态沥青中的石蜡分子单元而不会产生热滞后效应。石蜡的结晶会导致红外光谱在735~715 cm^-1处形成吸收峰,且吸收峰信号随温度降低而增强。沥青中的石蜡初期(0~8 h)析出较快,随着时间延长,析出速率放缓,持续时间可长达72 h。通过试验的直接观测,确定了沥青中低分子量石蜡的持续析出或沉淀是导致所用胶结料热可逆老化的根本原因。     

Vertical random vibration analysis of vehicle–track coupled system using Green's function method

A vertical vehicle–track coupled dynamic model, consisting of a high-speed train on a continuously supported rail, is established in the frequency-domain. The solution is obtained efficiently by use of the Green's function method, which can determine the vibration response over a wide range of frequency without any limitations due to modal truncation. Moreover, real track irregularity spectra can be used conveniently as input. The effect of the flexibility of both track and car body on the entire vehicle–track coupled dynamic response is investigated. A multi-body model of a vehicle with either rigid or flexible car body is defined running on three kinds of track: a rigid rail, a track stiffness model and a Timoshenko beam model. The results show that neglecting the track flexibility leads to an overestimation of both the contact force and the whole vehicle vibration response. The car body flexibility affects the ride quality of the vehicle and the coupling through the track and can be significant in certain frequency ranges. Finally, the effect of railpad and ballast stiffness on the vehicle–track coupled vibration is analysed, indicating that the stiffness of the railpad has an influence on the system in a higher frequency range than the ballast.     

Investigation of the effects of sleeper-passing impacts on the high-speed train

The sleeper-passing impact has always been considered negligible in normal conditions, while the experimental data obtained from a High-speed train in a cold weather expressed significant sleeper-passing impacts on the axle box, bogie frame and car body. Therefore, in this study, a vertical coupled vehicle/track dynamic model was developed to investigate the sleeper-passing impacts and its effects on the dynamic performance of the high-speed train. In the model, the dynamic model of vehicle is established with 10 degrees of freedom. The track model is formulated with two rails supported on the discrete supports through the finite element method. The contact forces between the wheel and rail are estimated using the non-linear Hertz contact theory. The parametric studies are conducted to analyse effects of both the vehicle speeds and the discrete support stiffness on the sleeper-passing impacts. The results show that the sleeper-passing impacts become extremely significant with the increased support stiffness of track, especially when the frequencies of sleeper-passing impacts approach to the resonance frequencies of wheel/track system. The damping of primary suspension can effectively lower the magnitude of impacts in the resonance speed ranges, but has little effect on other speed ranges. Finally, a more comprehensively coupled vehicle/track dynamic model integrating with a flexible wheel set is developed to discuss the sleeper-passing-induced flexible vibration of wheel set.     

An efficient and exact event-based algorithm for solving simplified first order dynamic network loading problems in continuous time

In this paper a novel solution algorithm is proposed for exactly solving simplified first order dynamic network loading (DNL) problems for any generalised network. This DNL solution algorithm, termed eLTM (event-based Link Transmission Model), is based on the seminal Lighthill–Witham–Richards (LWR) model, adopts a triangular fundamental diagram and includes a generalised first order node model formulation. Unlike virtually all DNL solution algorithms, eLTM does not rely on time discretisation, but instead adopts an event based approach. The main advantage of this approach is the possibility of yielding exact results. Furthermore, an approximate version of the same algorithm is introduced. The user can configure an a-priori threshold that dictates the approximation error (measurable a-posteriori). Using this approximation the computational effort required decreases significantly, making it especially suitable for large scale applications. The computational complexity is investigated and results are demonstrated via theoretical and real world case studies. Fixed periods of stationary demands are included adopting a matrix demand profile to mimic basic departure time demand fluctuations. Finally, the information loss of the approximate solution is assessed under different configurations.     

混合下单模式下在线餐饮订单配送优化模型

针对在线餐饮订单量激增及订单到达非均匀分布导致的调度不合理与资源浪费等问题，提出顾客提前下单与动态实时下单相结合的下单模式，研究此模式下订单配送优化. 考虑在线餐饮订单配送优化具有的动态VRP和多回程VRP属性，以最小化配送成本为目标，建立带有软时间窗的整数规划模型. 设计基于插入算法和2-opt 邻域搜索的混合启发式算法求解模型. 通过算例，分析提前下单顾客比例、提前下单时长等因素的影响. 结果表明，单个因素的增加会降低配送成本，当两者同时增加，因系统达到饱和使配送成本不升反降，因此要调整措施使顾客下单情况与系统配送能力相适应.     

蜂巢式液冷电池模块传热特性的试验研究

为4 A·h的21700型锂离子电池研发了蜂巢式液冷电池模块,并通过搭建的试验平台测定其充/放电过程的传热特性。结果表明:在25℃环境温度下,0.5C恒流恒压充电和1C恒流放电过程中,电池模块的最大温差均被控制在2℃以内;40℃环境温度下,1C恒流放电过程中,当冷却液流量大于1 L/min时电池模块的最大温差能保持在所要求的5℃以内。说明蜂巢式液冷电池模块冷却性能优良,可为未来电池热管理方案的设计提供技术支撑。     

接触网导线热过负荷保护的探讨

针对电气化铁道运行现状和铁路运输情况的变化,分析了目前电气化牵引变电所馈电线继电保护设置存在的不足,阐述了设置接触网导线热过负荷保护的必要性和保护原理,并结合国外过负荷保护装置的情况,提出了我国电气化铁道接触网导线热过负荷保护方案。