级配碎石裂缝缓解层防裂机理及足尺疲劳试验

反射裂缝是旧水泥混凝土路面沥青加铺层的主要病害之一,目前尚无理想的解决方法,针对这一问题,提出了采用级配碎石作为裂缝缓解层的方法。对级配碎石层的防裂机理进行了分析,采用大型反射裂缝试验台架进行了设置级配碎石层及其他对比结构层的加铺层疲劳破坏试验,模拟了沥青加铺层荷载型及温度型反射裂缝的产生、发展过程。结果表明,级配碎石防裂效果最好,玻纤格栅和土工布的防裂效果次之,普通沥青混凝土加铺层防裂效果最差。     

有沥青上面层的水泥混凝土路面的应力分析

叙述了有沥青上面层的水泥混凝土路面的荷载应力与温度应力公司方法，提出了简化计算公式。     

曲轴疲劳试验机自动控制系统的研制

为考核曲轴的弯曲疲劳强度 ,研制了一套由可编程控制器 (PIC)和PC机组成的高效、高自动化的试验装置 ,该装置可模拟曲轴在实际工况下的受力情况 ,测量所受应力的大小和分布等参数。实际应用证明 ,该装置具有较高的可靠性和自动化水平     

钢桥桥面沥青铺装层直道试验研究

在钢桥模型上进行了6种沥青混合料铺装层直道疲劳试验和高温车辙试验，研究了重复加载过程中应变变化规律，分析了桥面铺装层疲劳开裂性能，比较了各方案高温稳定性能。     

对二次空气改善车用汽油机排气净化效果的研究

在车用汽油机排气中CO和HC生成与热反应净化机理研究的基础上 ,通过试验探讨了二次空气对提高车用汽油机排气热反应净化效果的影响。研究结果表明 ,在发动机高速大负荷工况下 ,足量的二次空气能使CO和HC的排放浓度大幅度降低 ,而在发动机中等转速中小负荷工况下 ,由于排气温度低 ,二次空气对热反应净化效果影响不大     

Fatigue damage calculation for oil tanker and container ship structures

The fatigue behaviour of longitudinal stiffeners of oil tankers and container ships, subjected to dynamic loads, is analysed. The following dynamic load components are considered: hull girder vertical wave bending moment, alone and combined with the horizontal wave bending moment, hydrodynamic pressure and inertial forces caused by cargo acceleration.

The spectral method was selected to calculate the fatigue damage, based on S—N curves and Miner's rule. Following this approach, the fatigue damage may be calculated as a function of a stress parameter Ω_p, which represents the cumulative effect of wave induced loads in the unit of time and incorporates the combined effects of stress level and its occurring frequency.

Simple formulas for Ω_p of oil tankers and container ships are given, obtained from the results of hydrodynamic analyses performed on several ships, in different wave environments.

Several examples show the applicability of the methods to real ship structures. The method, however, still needs to be calibrated because of the simplifying hypotheses introduced in the loading conditions.     

钢桥面板纵肋顶板焊缝疲劳裂纹扩展的关键影响因素

正交异性钢桥面板疲劳问题突出，纵肋与顶板焊缝处是其关键疲劳易损部位，研究该部位疲劳裂纹的扩展过程并确定关键影响因素及其效应，有助于深刻理解其疲劳损伤机理。建立正交异性钢桥面板疲劳试验节段模型的有限元分析模型，将纵肋与顶板焊缝焊根处的疲劳裂纹近似为半椭圆形裂纹，基于断裂力学实现其扩展全过程的三维数值模拟。在此基础上研究初始裂纹的纵向位置和初始裂纹形状对疲劳裂纹扩展过程的影响，阐明扩展过程中的疲劳裂纹的形状变化，以及疲劳裂纹关键部位应力强度因子幅值的变化规律。研究表明：对于典型的正交异性钢桥面板纵肋与顶板焊缝，在纵向一段范围内，初始裂纹的纵向位置对裂纹扩展的影响不大；初始裂纹形状对裂纹扩展的影响主要体现在裂纹扩展的初始阶段，经过一段时间的扩展之后，不同形状的初始裂纹将演变为相对稳定的形状；持续一段时间后，裂纹将逐渐变得较为扁长；疲劳裂纹在深度方向上扩展超过约顶板厚度一半时，最深点的扩展速率将会减慢；深度相同的裂纹，形状越扁长时越倾向于向深度方向扩展，越不扁长时越倾向于向长度方向扩展。     

Driver fatigue: a vision-based approach to automatic diagnosis

In this paper, we describe a system that locates and tracks the eyes of a driver. The purpose of such a system is to perform detection of driver fatigue. By mounting a small camera inside the car, we can monitor the face of the driver and look for eye movements which indicate that the driver is no longer in condition to drive. In such a case, a warning signal should be issued. This paper describes how to find and track the eyes. We also describe a method that can determine if the eyes are open or closed. The primary criterion for this system is that it must be highly non-intrusive. The system must also operate regardless of the texture and the color of the face. It must also be able to handle changing conditions such as changes in light, shadows, reflections, etc. Initial experimental results are very promising even when the driver moves his/her head in a way such that the camera does not have a frontal view of the driver’s face.     

基于OpenFOAM的发动机舱回流计算方法研究

研究车辆在怠速工况下的发动机舱热空气回流问题，基于OpenFOAM 软件进行回流计算方法的开发。通过设置监控面及组分转换面来重新定义格栅新空气和舱内回流热空气等组分，可直接计算出回流在监控面上的分布及回流率和回流量。根据开发的方法对某款插电式混合动力汽车（Plug-in Hybrid Electric Vehicle，PHEV）车型进行计算并提出不同的优化方案，使其发动机舱回流率从32.7% 分别降低至24.0%和9.3%，回流量从0.169 kg/s分别降低至0.128 kg/s和0.048 kg/s，从而降低了冷凝器等散热器的进风温度，提高了怠速工况下热管理系统的性能。     

海洋工程用钢疲劳寿命与CTOD值关系的研究

通过对钻井平台上所用高强钢EQ70进行了韧度和疲劳性能的试验研究,得出了反映其韧度指标的裂纹尖端张开位移(CTOD)值和不同交变载荷下疲劳寿命值呈近似的线性关系.在应力幅值ΔP一定的情况下,疲劳寿命值N随着CTOD值的增大而增大,并且在高应力幅的时候,对数疲劳寿命和CTOD值有比较好的线性关系,最后还从微观意义上解释了产生这种关系的原因.