重载货车摩擦缓冲器阻抗特性的数值模拟

为预测摩擦缓冲器的实际工作状态,从几何特征和作用原理的角度,建立详细的MT-2型缓冲器理论模型。首先,通过对缓冲器内部各摩擦元件的运动学和静力学分析,推导出缓冲器在准静态下的阻抗特性;其次,引入附加摩擦系数量化各摩擦元件之间动静态摩擦过渡时的黏滞补偿,并模拟出缓冲器在动态下的阻抗特性;最后,利用C80型货车冲击试验数据对该缓冲器的理论模型进行验证。验证结果表明:总体上,数值模拟和现场试验下的缓冲器示功曲线基本吻合,说明模型的正确性;局部上数值模拟中缓冲器从加载Ⅰ阶段过渡至加载Ⅱ阶段的突变现象在冲击试验中表现的并不明显,还有待进一步完善。     

导电密封胶对不锈钢车体电阻点焊焊接性能影响研究

分析了电阻点焊原理,对相同的点焊搭接方式,分别采用3种工况进行焊接试验。3种工况分别采用相同焊接参数对搭接接触面涂导电密封胶和不涂导电密封胶的试件进行焊接;优化焊接参数后,对搭接接触面涂导电密封胶的试验件进行焊接。对3种工况下完成的焊接试件进行拉伸力检测试验、金相熔核尺寸检测和缺陷检测试验,对熔核直径、拉伸力、熔核内部缺陷的试验结果进行分析。试验结果表明:导电密封胶对电阻点焊的焊接性能存在影响;通过适当优化焊接参数,可以提高涂导电密封胶试件的焊接性能,焊接质量能够满足产品焊接要求。     

船用电器柜抗冲击设计研究

为增强船内部电器柜的抗冲击性能,采用有限元法对船内不同安装型式的电器柜结构进行了模态和抗冲击性能仿真分析,通过对比分析得出了使用撑杆加固型式安装的电器柜能显著提高船内电器柜的抗冲击性能的结论,并确定了电器柜抗冲击优化设计方案。     

Mode jumping in the lateral buckling of subsea pipelines

Unburied subsea pipelines under high-temperature conditions tend to relieve their axial compressive stress by forming localised lateral buckles. This phenomenon is traditionally studied under the assumption of a specific lateral deflection profile (mode) consisting of a fixed number of lobes. We study lateral thermal buckling as a genuinely localised buckling phenomenon by applying homoclinic (‘flat’) boundary conditions. By not having to assume a particular buckling mode we are in a position to study transitions between these traditional modes in typical loading sequences. For the lateral resistance we take a realistic nonlinear pipe-soil interaction model for partially embedded pipelines. We find that for soils with appreciable breakout resistance, i.e., nonmonotonicity of the lateral resistance characteristic, sudden jumps between modes may occur. We consider both symmetric and antisymmetric solutions. The latter turn out to require much higher temperature differences between pipe and environment for the jumps to be induced. We carry out a parameter study on the effect of various pipe-soil interaction parameters on this mode jumping. Away from the jumps post-buckling solutions are reasonably well described by the traditional modes whose analytical expressions may be used during preliminary design.     

盾构下坡掘进对推进阻力的影响研究

以神华新街6°煤矿斜井盾构工程为背景,针对盾构下坡掘进工况,通过建立盾构上作用的水土压力载荷与坡度的数学关系模型,推导出推进阻力与坡度的数学公式。结合工程实例,计算水平掘进与6°下坡掘进各推进阻力值,并利用MATLAB软件绘制下坡掘进时推进阻力随坡度变化的曲线。结果表明:1)6°下坡掘进的总推进阻力相对于水平掘进仅减小了约8%,坡度小于13°时,可通过水平掘进时的推进阻力减去重力沿掘进轴线上的分量来近似求得,且偏差小于10%;2)总推进阻力会随坡角的不断增大而减小;3)当坡度大于50.4°后,盾构有自动向下滑移的趋势,刀盘将自动压紧开挖面,导致刀具自动嵌入开挖面,增加了启动扭矩与换刀的难度。     

城市地下道路分(合)流匝道通风阻力特性

为分析多点进出结构的城市地下道路空气流动特性,以长沙市营盘路湘江隧道为原型,通过现场实测、缩尺模型试验以及CFD软件数值模拟方法,对分(合)匝道通风阻力特性进行了研究,考察了雷诺数、风量比、分岔角度对分(合)流匝道阻力特性的影响规律。研究结果表明:1)主隧道与匝道风量比、主隧道与匝道夹角是影响分(合)流匝道局部阻力系数的关键因素;2)城市地下道路分(合)流匝道局部阻力变化特性,不宜简单套用通风管道的三通构件的参数;3)结合最小二乘法和Matlab软件对计算结果进行多因素回归分析,给出了基于长沙营盘路湘江隧道的分(合)流匝道主隧道和匝道的局部阻力系数关联式。研究结果可为复杂结构城市地下道路通风系统阻力特性分析及通风工程优化设计提供方法参考。     

约束对隧道二次衬砌早期温度应力分布的影响

为了解决隧道工程渗水问题,基于某隧道工程,采用MIDAS-GEN对其二次衬砌早期模筑混凝土进行非稳定温度应力场以及周围约束进行研究。研究结果表明:约束可以改变隧道的早期拉应力场的分布,具有外围约束的隧道二次衬砌的拉应力为隧道厚度中间最大,无约束隧道的拉应力为外部最大,约束可以减小隧道外部区域的拉应力,使得远离约束区域的拉应力变大,而无约束隧道的拉应力分布与之相反。根据温度应力分布特点,建议在设计方面适当增大二次衬砌中间与外侧的配筋,在施工方面减小初期支护与二次砌衬之间约束等。     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

掺混甲烷对乙烯层流预混火焰炭烟形貌的影响

针对掺混甲烷的乙烯层流火焰中的炭烟颗粒从形貌角度进行了研究,构建了具有相同当量比(2.07)、火焰温度、气体流速的层流预混乙烯火焰和掺混甲烷的乙烯火焰,并各自选取了3个高度进行热泳探针取样,采用TEM和AFM方法对各个工况的炭烟颗粒粒径分布、平均粒径、平均体积当量球径进行了对比。发现少量的甲烷掺混会令乙烯火焰中炭烟颗粒的尺寸变大,而当甲烷掺混量变多时该现象消失。而通过对颗粒的圆度、球度和分形维数计算和分析,发现即使是很小的颗粒也具有相似的不规则形状,这一现象广泛存在于各种火焰和各种大小的颗粒中,不受掺混比的影响,并且越大的颗粒结构越松散。     

���˹���������������ɢ��������ʵ֤����

国家体育场作为北京奥运会的主会场成功地承担了开闭幕式和田径赛事任务。本文研究了其停车场车辆的交通疏散问题,制定了疏散方案。首先,分析了国家体育场停车场和泊位布局及车辆疏散的具体条件。其次,通过给定环境的场景和参数设定,对具体的奥运场馆停车场车辆的疏散方案进行了仿真和评价。最后,利用奥运会开幕式的车辆疏散实测数据进行了对比分析,在仿真中要员和贵宾车辆的总疏散时间为26min,而奥运会开幕式车辆疏散实测结果表明,全部要员、贵宾疏散完毕,共用时27min,从而验证了车辆疏散方案的准确性和实用性。