基于现场钻芯取样的沥青结构层抗车辙性能评价方法

为了快速检测与评价所铺筑沥青路面结构的抗车辙性能,提高沥青路面施工质量水平,首先设计了圆柱形试件车辙试验所需的试验模具,采用ANSYS软件模拟圆柱形试件和板式试件的车辙试验,分析了圆柱形芯样车辙试验的可行性;其次采用2种基质沥青、1种改性沥青、5种级配的5组沥青混合料,在不同厚度和温度条件下进行圆柱形芯样车辙试验,分析确定了圆柱形芯样车辙试验的条件;最后结合现行规范要求,根据板式试件车辙试验和圆柱形试件车辙试验的相关性,建立了基于现场钻芯取样的沥青路面抗车辙性能检测标准。研究结果表明:可采用70℃下路面圆柱形芯样的车辙试验评价沥青路面高温抗车辙能力,并要求高温性能质量标准下的车辙动稳定度大于2 450次.mm-1;该法可实现对现场沥青路面抗车辙性能的快速检测与评价,有利于提高混合料设计水平与路面施工质量。     

Tangential force variation due to the bogie direction reversal procedure

A range of tangential forces is generated within the contact patch when a wheelset moves on the rail. These forces are intensified when incorporating curved tracks and motored axle rail vehicles [Arrus, P., de Pater, A.D. and Meyers, P., 2002, The stationary motion of a one-axle vehicle along a circular curve with real rail and wheel profiles. Vehicle System Dynamics, 37(1), 29–58]. The wheelset is subject to flange contact if an unbalanced force remains in a curve towards the high rail gauge face. The resultant force in the transverse direction includes the lateral force, the radial force, and the creep forces in addition to the effect of the frequent wheelset displacement due to the kinematic oscillation [Iwnicki, S., 2003, Simulation of wheel–rail contact forces. Fatigue Fracture Engineering Material Structure, 26, 887–900]. This article has focused on a potential variation in some of the forces cited when the wheelset is subject to backward and forward movements. A severe wear rate observed within the wheel flange region in Iranian Railways was investigated by operating a test bogie on a curvaceous track. An obvious improvement in the wear rate and wear pattern of the wheels was attained when the second test bogie encountered a bogie direction reversal procedure. This enhancement is considered in this article from the force analysis standpoint.     

Mathematical modelling of train–turnout interaction

The paper proposes a mathematical model of train–turnout interaction in the mid-frequency range (0–500 Hz). The model accounts for the effects of rail profile variation along the track and of local variation of track flexibility. The proposed approach is able to represent the condition of one wheel being simultaneously in contact with more than one rail, allowing the accurate prediction of the effect of wheels being transferred from one rail to another when passing over the switch toe and the crossing nose. Comprehensive results of train–turnout interaction during the negotiation of the main and the branch lines are presented, including the effect of wear of wheel/rail profiles and presence of track misalignment. In the final part of the paper, comparisons are performed between the results of numerical simulations and line measurements performed on two different turnouts for urban railway lines, showing a good agreement between experimental and numerical results.     

Theoretical and experimental excitation force spectra for railway-induced ground vibration: vehicle–track–soil interaction,irregularities and soil measurements

Excitation force spectra are necessary for a realistic prediction of railway-induced ground vibration. The excitation forces cause the ground vibration and they are themselves a result of irregularities passed by the train. The methods of the related analyses – the wavenumber integration for the wave propagation in homogeneous or layered soils, the combined finite-element boundary-element method for the vehicle–track–soil interaction – have already been presented and are the base for the advanced topic of this contribution. This contribution determines excitation force spectra of railway traffic by two completely different methods. The forward analysis starts with vehicle, track and soil irregularities, which are taken from literature and axle-box measurements, calculates the vehicle–track interaction and gets theoretical force spectra as the result. The second method is a backward analysis from the measured ground vibration of railway traffic. A calculated or measured transfer function of the soil is used to determine the excitation force spectrum of the train. A number of measurements of different soils and different trains with different speeds are analysed in that way. Forward and backward analysis yield the same approximate force spectra with values around 1 kN for each axle and third of octave.     

Dynamic model for the wheel–rail contact friction

Accurately estimating the coefficient of friction (CoF) is essential in modelling railroad dynamics, reducing maintenance costs, and increasing safety in rail operations. The typical assumption of a constant CoF is widely used in theoretical studies; however, it has been noticed that the CoF is not constant, but rather depends on various dynamic parameters and instantaneous conditions. In this paper, we present a newly developed three-dimensional nonlinear CoF model for the dry rail condition and test the CoF variation using this model with estimated dynamic parameters. The wheel–rail is modelled as a mass–spring–damper system to simulate the basic wheel–rail dynamics. Although relatively simple, this model is considered sufficient for the purpose of this study. Simulations are performed at a train speed of 20 m/s using rail roughness as an excitation source. The model captures the CoF extremes and illustrates its nonlinear behaviour and instantaneous dependence on several structural and dynamic parameters.     

An ABS control logic based on wheel force measurement

The paper presents an anti-lock braking system (ABS) control logic based on the measurement of the longitudinal forces at the hub bearings. The availability of force information allows to design a logic that does not rely on the estimation of the tyre–road friction coefficient, since it continuously tries to exploit the maximum longitudinal tyre force.

The logic is designed by means of computer simulation and then tested on a specific hardware in the loop test bench: the experimental results confirm that measured wheel force can lead to a significant improvement of the ABS performances in terms of stopping distance also in the presence of road with variable friction coefficient.     

Adhesion estimation at the wheel–rail interface using advanced model-based filtering

The railway industry in the UK is currently expanding the use of condition monitoring of railway vehicles. These systems can be used to improve maintenance procedures or could potentially be used to monitor current vehicle running conditions without the use of cost prohibitive sensors. This paper looks at a novel method for the online detection of areas of low adhesion in the wheel/rail contact that cause significant disruption to the running of a network, particularly in the autumn season. The proposed method uses a Kalman–Bucy filter to estimate the creep forces in the wheel–rail contact area; post-processing is then applied to provide information indicative of the actual adhesion level. The algorithm uses data that, in practice, would be available from a set of modest cost inertial sensors mounted on the vehicle bogie and wheel-sets. The efficacy of the approach is demonstrated using simulation data from a nonlinear dynamic model of the vehicle and its track interface.     

Optimisation of railway crossing geometry considering a representative set of wheel profiles

A numerical method for robust geometry optimisation of railway crossings is presented. The robustness is achieved by optimising the crossing geometry for a representative set of wheel profiles. As a basis for the optimisation, a crossing geometry is created where rail cross-sectional profiles and longitudinal height profiles of both wing rails and crossing nose are parameterised. Based on the approximation that the two problems are decoupled, separate optimisations are performed for the cross-sectional rail profiles and the longitudinal height profiles. The rail cross sections are optimised to minimise the maximum Hertzian wheel–rail contact pressure. The longitudinal height profiles are optimised to minimise the accumulated damage in the wing rail to crossing nose transition zone. The accumulated damage is approximated using an objective criterion that accounts for the angle of the wheel trajectory reversal during the transition from the wing rail to the crossing nose as well as the distribution of transition points for the utilised wheel profile set. It is found that small nonlinear height deviations from a linear longitudinal wing rail profile in the transition zone can reduce the objective compared to the nominal design. It is further demonstrated that the variation in wheel profile shapes, lateral wheel displacements and the feasible transition zone length of the crossing will determine the longitudinal height profiles of the wing rail and crossing nose if all wheel profiles are to make their transition within the transition zone.     

Influence of polygonal wear of railway wheels on the wheel set axle stress

The coupled vehicle/track dynamic model with the flexible wheel set was developed to investigate the effects of polygonal wear on the dynamic stresses of the wheel set axle. In the model, the railway vehicle was modelled by the rigid multibody dynamics. The wheel set was established by the finite element method to analyse the high-frequency oscillation and dynamic stress of wheel set axle induced by the polygonal wear based on the modal stress recovery method. The slab track model was taken into account in which the rail was described by the Timoshenko beam and the three-dimensional solid finite element was employed to establish the concrete slab. Furthermore, the modal superposition method was adopted to calculate the dynamic response of the track. The wheel/rail normal forces and the tangent forces were, respectively, determined by the Hertz nonlinear contact theory and the Shen–Hedrick–Elkins model. Using the coupled vehicle/track dynamic model, the dynamic stresses of wheel set axle with consideration of the ideal polygonal wear and measured polygonal wear were investigated. The results show that the amplitude of wheel/rail normal forces and the dynamic stress of wheel set axle increase as the vehicle speeds rise. Moreover, the impact loads induced by the polygonal wear could excite the resonance of wheel set axle. In the resonance region, the amplitude of the dynamic stress for the wheel set axle would increase considerably comparing with the normal conditions.