忻阜高速公路古峪沟高架桥设计

古峪沟高架桥是忻州至阜平高速公路忻州-长城岭段高速公路第五合同段的一座特大桥梁,地形、地质条件复杂,设计中采用了一些非常规的设计思路,对同类桥梁设计具有较好的借鉴作用。     

大跨悬索桥主缆线形解析迭代法研究

基于悬索桥在恒载作用下的受力特点,建立了主缆线形控制计算的解析迭代方法,以此确定主缆无应力长度、成桥线形、空缆线形。算例结果表明该解析法具有适合程序计算、收敛速度快、计算精度高的特点,可用于悬索桥设计与施工控制计算。     

公路黄土隧道洞口段施工技术要点

由于黄土隧道自身稳定性差,在开挖过程中,特别是刚进洞时的洞口（浅埋）段,容易出现不稳定的问题,所以需认清洞口段常见的灾害类型及成因,加强施工中各个环节的控制,以保证施工的正常、安全进行。     

高墩大箱室梁墩顶0号段托架的设计与施工技术

介绍了高墩大箱室箱梁墩顶0号段悬托架的设计与施工方法,通过直接在墩身预埋牛腿,在牛腿上安放工字钢大梁和贝雷架分配梁以作为托架支撑,经计算后满足施工需要,从而优化施工方案。     

关于《钢质内河船舶建造规范》(2009)总纵强度问题的探讨

本文简要阐述了影响船舶总纵强度的主要因素,并对《钢质内河船舶建造规范》（2009）中将船舯剖面处的最小剖面模数表示成型深D的表达形式提出了自己的见解,并指出了总纵弯矩与中剖面最小剖面模数计算公式中的不协调。     

单舰舰空导弹对空防御问题研究

舰空导弹武器系统是防御反舰导弹的有效兵器之一,舰空导弹的战术技术性能决定了舰空导弹拦截反舰导弹的能力。舰空导弹的反导能力主要取决于舰空导弹的单发命中概率、目标的性质及对不同来袭方向反舰导弹的抗击次数,舰空导弹武器系统性能的优劣直接关系和影响舰艇的生存能力。     

基于切片技术的点云数据预处理研究

针对扫描点云杂乱无序的特点,讨论了点云数据预处理的问题,提出了一种新的基于点云切片的数据预处理迭代算法．通过对点云最小包围盒进行均匀分割及分割后点云的密度分析,对密度过大的分割块进行迭代分割,建立了3个方向的点云切片和截面线．结果不仅大大减少了点云数据量,并且在点云密度过大的区域很好地保持了模型的原始特征,同时将原始的无序数据点集转化为具有层列结构的有序组织形式,确定了各点之间的相互关系,为后续曲线曲面拟合做了很好的准备．     

Database of sail shapes versus sail performance and validation of numerical calculations for the upwind condition

A database of full-scale three-dimensional sail shapes is presented with the aerodynamic coefficients for the upwind condition of International Measurement System (IMS) type sails. Three-dimensional shape data are used for the input of numerical calculations and the results are compared with the measured sail performance. The sail shapes and performance were measured using sail dynamometer boat Fujin. This is a boat of 10.3-m length overall in which load cells and CCD cameras were installed to simultaneously measure the sail forces and shapes. At the same time, the sailing conditions of the boat, e.g., boat speed, heel angle, wind speed, and wind angle, were measured. The sail configurations tested were: mainsail with 130% jib, mainsail with 75% jib, and mainsail alone. Sail shapes were measured at several vertical positions for the shape parameters defined by: chord length, maximum draft, maximum draft position, entry angle at the luff, and exit angle at the leech, all of which finally yield three-dimensional coordinates of the sail geometry. The tabulated shape data, along with aerodynamic coefficients, are presented in this article. In addition, numerical flow simulations were performed for the measured sail shapes and the sailing conditions to investigate the capability and limitations of the methods through detailed comparison with the measurements. Two numerical methods were used: a vortex lattice method (VLM) and a Reynolds-averaged Navier–Stokes (RANS)-based computational fluid dynamics method. The sail shape database, in association with the numerical results, provides a good benchmark for the sail performance analysis of the upwind condition of IMS type sails.     

Water entry of a bow-flare ship section with roll angle

The two-dimensional water entry of a bow-flare ship section with constant roll angle, or heel angle, was studied by using a boundary element method. The fully nonlinear free surface conditions and exact body boundary conditions were satisfied. Nonviscous flow separation from the knuckles of the section or from the curved bottom could be simulated. The numerical calculations were compared with existing experimental results. First, the effects of roll angle were investigated and then the characteristics associated with large roll angles were examined in particular. The evolution of the free surfaces and the pressure distributions on the section surface are illustrated and the influence of nonviscous flow separation from the leeward section surface is discussed.     

T型焊接接头疲劳性能研究

T型焊接接头在船舶与海洋工程结构中广泛应用,研究T型焊接接头的疲劳性能对于提高船舶与海洋工程结构的强度具有重要意义.针对工程中常用的四种焊趾形式的T型焊接接头,利用有限元计算和模型试验两种方法对其疲劳性能进行了研究.结果表明,平面型焊趾是较优的T型接头焊趾形式.