含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

冲压机械振动对高铁桥梁及行车动力影响分析

高速铁路桥梁的平顺性和稳定性对运营列车的平稳性和安全性有很大影响。为研究冲压机械产生的外部振动激励对高铁桥梁的影响,首先通过对此机械引起的地面振动进行实测,并结合有限元分析软件,确定最大冲击荷载作用下产生的地面振动及传播至桥墩处的振动;然后通过建立列车-轨道-桥梁耦合动力学模型,将桥墩处的地面振动作为激励输入,分析列车以不同速度通过时车辆、桥梁动力学响应。结果表明:地面冲击振动有限元模型计算结果与实测结果基本相符,验证了模型的可靠性;地面振动对桥梁响应会产生一定的影响,距振源50 m处地面振动对桥梁所产生的影响较距振源80 m处(桥墩处)的大,但对运行车辆的影响很小;随着车速由250 km/h至350 km/h,车辆及桥梁各结构的动态响应均有所增大,但都未超出安全限值。因此,冲压机械冲击作用导致的地面振动对列车-轨道-桥梁系统动态服役性能影响非常有限。     

Tyre/road noise damping characteristics using nomographs and fundamental vibroacoustical relationships

Several studies have successfully developed laboratory and field measurement techniques to estimate tyre/road noise damping characteristics. However, laboratory–field noise correlations of pavement types in the form of nomographs is essential to cognize the pavements’ acoustical properties from a practical perspective. A toolkit that readily provides field tyre/road noise intensity of different pavement materials is needed. Thus, the main objective of this study was to develop nomographs with relationships for tyre/road noise versus pavement materials’ viscoelastic–vibroacoustical properties. Isothermal and isochronal nomographs of phase angle–tyre/road noise as toolkits were developed based upon well-established phase angle and noise intensities typical of mixtures, making the nomograph correlations very authentic, realistic, and novel along with benefit to predict tyre/road noise at any desired temperature and traffic speed (or frequency) combination. This study is envisaged to benefit in the discernment of road materials’ damping capabilities from vibroacoustical and field noise–viscoelastic relation aspects.     

Hydroelastic analysis of oblique irregular waves with a pontoon-type VLFS edged with dual inclined perforated plates

The fluid-structure interaction of oblique irregular waves with a pontoon-type very large floating structure (VLFS) edged with dual horizontal/inclined perforated plates has been investigated in the context of the direct time domain modal expansion theory. For the hydroelastic analysis, the boundary element method (BEM) based on time domain Kelvin sources is implemented to establish water wave model including the viscous effect of the perforated plates through the Darcy’s law, and the finite element method (FEM) is adopted for solving the deflections of the VLFS modeled as an equivalent Mindlin thick plate. In order to enhance the computing efficiency, the interpolation-tabulation scheme is applied to assess rapidly and accurately the free-surface Green function and its partial derivatives in finite water depth, and the boundary integral equation of a half or quarter VLFS model is further established taking advantage of symmetry of flow field and structure. Also, the numerical solutions are validated against a series of experimental tests. In the comparison, the empirical relationship between the actual porosity and porous parameter is successfully applied. Numerical solutions and model tests are executed to determine the hydroelastic response characteristics of VLFS with an attached anti-motion device. This study examines the effects of porosity, submerged depth, inclined angle and gap distance of such dual perforated anti-motion plates on the hydroelastic response to provide information regarding the optimal design. The effects of oblique wave angle on the performance of anti-motion and hydroelastic behavior of VLFS are also emphatically examined.     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

A capacity maximization scheme for intersection management with automated vehicles

With the advent of connected and automated vehicle technology, in this paper, we propose an innovative intersection operation scheme named as MCross: Maximum Capacity inteRsection Operation Scheme with Signals. This new scheme maximizes intersection capacity by utilizing all lanes of a road simultaneously. Lane assignment and green durations are dynamically optimized by solving a multi-objective mixed-integer non-linear programming problem. The demand conditions under which full capacity can be achieved in MCross are derived analytically. Numerical examples show that MCross can almost double the intersection capacity (increase by as high as 99.51% in comparison to that in conventional signal operation scheme).     

Integrating mesoscopic dynamic traffic assignment with agent-based travel behavior models for cumulative land development impact analysis

A number of approaches have been developed to evaluate the impact of land development on transportation infrastructure. While traditional approaches are either limited to static modeling of traffic performance or lack a strong travel behavior foundation, today’s advanced computational technology makes it feasible to model an individual traveler’s response to land development. This study integrates dynamic traffic assignment (DTA) with a positive agent-based microsimulation travel behavior model for cumulative land development impact studies. The integrated model not only enhances the behavioral implementation of DTA, but also captures traffic dynamics. It provides an advanced yet practical approach to understanding the impact of a single or series of land development projects on an individual driver’s behavior, as well as the aggregated impacts on the demand pattern and time-dependent traffic conditions. A simulation-based optimization (SBO) approach is proposed for the calibration of the modeling system. The SBO calibration approach enhances the transferability of this integrated model to other study areas. Using a case study that focuses on the cumulative land development impact along a congested corridor in Maryland, various regional and local travel behavior changes are discussed to show the capability of this tool for behavior side estimations and the corresponding traffic impacts.     

Balancing energy consumption and risk of delay in high speed trains: A three-objective real-time eco-driving algorithm with fuzzy parameters

Eco-driving is an energy efficient traffic operation measure that may lead to important energy savings in high speed railway lines. When a delay arises in real time, it is necessary to recalculate an optimal driving that must be energy efficient and computationally efficient.In addition, it is important that the algorithm includes the existing uncertainty associated with the manual execution of the driving parameters and with the possible future traffic disturbances that could lead to new delays.This paper proposes a new algorithm to be executed in real time, which models the uncertainty in manual driving by means of fuzzy numbers. It is a multi-objective optimization algorithm that includes the classical objectives in literature, running time and energy consumption, and as well a newly defined objective, the risk of delay in arrival. The risk of delay in arrival measure is based on the evolution of the time margin of the train up to destination.The proposed approach is a dynamic algorithm designed to improve the computational time. The optimal Pareto front is continuously tracked during the train travel, and a new set of driving commands is selected and presented to the driver when a delay is detected.The algorithm evaluates the 3 objectives of each solution using a detailed simulator of high speed trains to ensure that solutions are realistic, accurate and applicable by the driver. The use of this algorithm provides energy savings and, in addition, it permits railway operators to balance energy consumption and risk of delays in arrival. This way, the energy performance of the system is improved without degrading the quality of the service.     

学生体质健康状况动态分析与应对策略——以辽宁省交通高等专科学校为例

本文把在校大三学生为研究主体对象,对其3年的体质测试数据进行动态的形式分析,为准确地掌握学生的体质健康状况的变化规律和存在的问题,以便在日后的体育教学中科学地指导和有针对性的开展体育教学工作,更好地促进学生体质的健康发展和改进学校体育教学。