基于沉降差的填石路堤施工工艺与质量控制研究

结合南方地区填石路堤施工,通过填石路堤试验段研究,介绍了填石路堤的施工工艺和质量控制要求,并通过沉降差检测分析,说明了沉降差作为填石路堤质量控制指标的可行性,为同类工程提供参考.     

公路沥青混凝土路面施工质量控制措施探析

沥青是我国用于公路路面铺设的典型材料.对沥青混凝土路面施工质量控制进行分析,并提出相应的施工质量控制措施,为施工企业提供借鉴.     

Signal control optimization for automated vehicles at isolated signalized intersections

Traffic signals at intersections are an integral component of the existing transportation system and can significantly contribute to vehicular delay along urban streets. The current emphasis on the development of automated (i.e., driverless and with the ability to communicate with the infrastructure) vehicles brings at the forefront several questions related to the functionality and optimization of signal control in order to take advantage of automated vehicle capabilities. The objective of this research is to develop a signal control algorithm that allows for vehicle paths and signal control to be jointly optimized based on advanced communication technology between approaching vehicles and signal controller. The algorithm assumes that vehicle trajectories can be fully optimized, i.e., vehicles will follow the optimized paths specified by the signal controller. An optimization algorithm was developed assuming a simple intersection with two single-lane through approaches. A rolling horizon scheme was developed to implement the algorithm and to continually process newly arriving vehicles. The algorithm was coded in MATLAB and results were compared against traditional actuated signal control for a variety of demand scenarios. It was concluded that the proposed signal control optimization algorithm could reduce the ATTD by 16.2–36.9% and increase throughput by 2.7–20.2%, depending on the demand scenario.     

起伏基岩地层盾构姿态控制及刀具配置分析

为了解决在起伏基岩地层中盾构掘进姿态控制困难及刀盘不均匀消耗问题,以长沙地铁2号线西延线盾构区间为工程实例,通过对现场油缸推力关系统计分析,得出盾构区间直线段和曲线段地层由软至硬和由硬至软的合理的油缸推力比,并应用于工程实际,得出相应的直线段和曲线段的水平、竖向偏差且均满足轴线偏差不超过50 mm的标准要求。同时,通过对现场每百米刀具更换情况统计分析,得出合理的刀具改良配置建议。     

Plate scanning tools to obtain travel times in traffic networks

The management of vehicle travel times has been shown to be fundamental to traffic network analysis. To collect travel time measurement, some methods focus solely on isolated links or highway segments, and where two measurement points, at the beginning and at the end of a section, are deemed sufficient to evaluate users' travel time. However, in many cases, transport studies involve networks in which the problem is more complex. This article takes advantage of the plate scanning technique to propose an algorithm that minimizes the required number of registering devices and their location in order to identify vehicles candidates to compute the travel times of a given set of routes (or subroutes). The merits of the proposed method are explained using simple examples and are illustrated by its application to the real network of Ciudad Real.     

Robust traffic assignment model: Formulation,solution algorithms and empirical application

ABSTRACT

The deterministic traffic assignment problem based on Wardrop's first criterion of traffic network utilization has been widely studied in the literature. However, the assumption of deterministic travel times in these models is restrictive, given the large degree of uncertainty prevalent in urban transportation networks. In this context, this paper proposes a robust traffic assignment model that generalizes Wardrop's principle of traffic network equilibrium to networks with stochastic and correlated link travel times and incorporates the aversion of commuters to unreliable routes.

The user response to travel time uncertainty is modeled using the robust cost (RC) measure (defined as a weighted combination of the mean and standard deviation of path travel time) and the corresponding robust user equilibrium (UE) conditions are defined. The robust traffic assignment problem (RTAP) is subsequently formulated as a Variational Inequality problem. To solve the RTAP, a Gradient Projection algorithm is proposed, which involves solving a series of minimum RC path sub-problems that are theoretically and practically harder than deterministic shortest path problems. In addition, an origin-based heuristic is proposed to enhance computational performance on large networks. Numerical experiments examine the computational performance and convergence characteristics of the exact algorithm and establish the accuracy and efficiency of the origin-based heuristic on various real-world networks. Finally, the proposed RTA model is applied to the Chennai road network using empirical data, and its benefits as a normative benchmark are quantified through comparisons against the standard UE and System Optimum (SO) models.     

广东山区高速公路挖方边坡常见病害及防治策略

广东省山区高速公路发展迅速,但诸多挖方边坡在修建过程中就产生了不同程度的病害。这些病害产生的原因包括气候、地质条件和人为因素,给施工工期、造价及安全管理造成较大影响。鉴于塌方病害在广东地区山区高速公路挖方边坡中较为常见,根据破坏方式及影响范围的深度将其划分为浅层溜塌、浅层滑塌和深层滑塌(滑坡)。结合工程建设经验,提出了山区路堑边坡的防治策略,可为类似工程的设计、施工提供借鉴。     

南昌红谷沉管隧道短管节干坞内拉合对接施工技术

沉管隧道最终接头短管节在牵移和拉合过程中易发生偏移与倾斜,且GINA止水带压缩到设计值难度较大。以南昌红谷沉管隧道为例,从准备、牵移、拉合及后处理4个阶段介绍短管节对接拉合施工工艺。通过对底钢板打磨、涂抹黄油等,减小底部摩擦阻力。采用计算机控制液压同步提升系统、液压数据量测、钢端壳间距测量等措施,对短管节轴线及平面控制。实践表明:GINA止水带压缩量误差仅为+4 mm,短管节轴线及平面偏差均在可控范围内,短管节干坞内拉合对接操作可行、质量可靠。     

我国城市防洪排涝地下深隧规划设计与施工方法

为了建设符合中国国情的地下排水深隧,解决城市内涝问题,消除"城市看海"现象,采用调研分析的研究方法,通过调研国外城市排水深隧建设的成功案例,借鉴成熟经验并结合我国国情探索出我国城市排水深隧在规划设计、施工技术等方面的建设模式。主要结论如下:1)深隧规划必须坚持雨污分流原则,防涝标准应设为百年一遇;2)深隧层位应建于地下30~50 m的位置,隧道管线应布设在城市易涝区,并且将修建深隧、改造浅管和清淤河道衔接起来,形成一套完整的防洪排涝系统,让深隧的作用得以充分发挥,才能解决城市内涝问题;3)排水深隧要注重防水设计,防止雨水污染地下水;4)为提高深隧的经济效益,应将深隧与地下快速路的规划结合起来,功能上多样化。     

水中悬浮隧道交通荷载模拟方法研究

为研究水中悬浮隧道交通荷载的合理模拟方法以及交通荷载对隧道结构的影响,借鉴铁路、公路交通荷载的模拟方法,综合考虑车辆轮载、路面不平度、行车速度以及外部激励荷载等影响因素的共同作用,提出水中悬浮隧道交通荷载的模拟表达式。通过数值模拟计算,分析悬浮隧道交通荷载的变化特征,并研究不同交通荷载模拟方法对悬浮隧道结构振动位移响应的影响。结果表明:文章提出的交通荷载模拟方法计算结果符合移动振动荷载的波动性和周期性特征。在对结构振动位移响应影响方面,固定均布荷载相当于静载,移动集中荷载和移动振动荷载时的位移变化幅值相对固定均布荷载时的大且影响相似,但移动振动荷载时的振幅稍大,体现了交通荷载中动荷载部分对结构振动位移响应的影响,更适合用来模拟悬浮隧道中的交通荷载。