Development and validation of a direct mode choice model

A direct discrete mode choice model is introduced using relative attributes of competing modes as well as socioeconomic characteristics of travelers. The model is calibrated and validated for two available historic databases in the Dallas–Fort Worth region. The validation is conducted against the outputs of a current nested logit model used by the regional planning organization as well as the observed values based on transit ridership surveys for a newly inaugurated commuter rail service. The calibrated model is applied after the introduction of this new transit mode. The results show that the estimated mode shares by the proposed model have a statistically better consistency with the observed values than the estimates of the conventional nested logit model. Unlike the logit model, the structure of the direct model based on relative attributes also has the advantage of not needing recalibration each time a new travel mode is introduced. The model is found to be easier to calibrate and produces more accurate results than the nested logit model, commonly used by many metropolitan planning organizations.     

Energy savings in transport

A decade of increasing Federal attention to urban transportation needs has culminated in the 1970 Urban Mass Transportation Assistance Act. This Act is intended to provide 10 thousand million dollars over the next 12 years in Federal assistance money to urban public transportation systems. This paper examines the needs of selected U.S. cities as a basis for (1) understanding the vast, various and complex transportation needs of urban areas throughout the country, and (2) assessing the sufficiency of these funds. The sample cities have been placed into three broad categories based on the state of development of their transportation systems. In Category I cities, the essential need is to ensure the survival of bus systems for the use of non‐drivers, or to provide some other viable alternative to the automobile; in Category II cities, the primary needs are to relieve auto congestion and to improve public transportation components, while in Category III cities, the primary need is massive investment to improve and to extend public transportation facilities. It is concluded that the presently intended Federal funding level for transportation will not meet the financial requirements of the Category III cities.     

Multi-objective control of a full-car model using linear-matrix-inequalities and fixed-order optimisation

This paper studies multi-objective control of a full-vehicle suspension excited by random road disturbances. The control problem is first formulated as a mixed ?₂/?_∞ synthesis problem and an output-feedback solution is obtained by using linear-matrix-inequalities. Next, the multi-objective control problem is re-formulated as a non-convex and non-smooth optimisation problem with controller order restricted to be less than the vehicle model order. For a range of orders, controllers are synthesised by using the HIFOO toolbox. The efficacy of the presented procedures are demonstrated by several design examples.     

The IMMa optimisation algorithm without control input parameters

The IMMa optimisation algorithm (IOA) consists of a heuristic method based on a differential evolution algorithm for choosing the Magic Formula (MF) tyre model parameters. In a previous paper, we demonstrated that the IOA improved the searching procedure of optimum MF parameters with respect to the starting value optimisation (SVO) methods. But we had to introduce some control input parameters that were fixed during the running process. Now, the new version does not require control input variables to be chosen by the user. That is, we use an algorithm with self-adapting control parameters and it continues being easy to use, robust and fast. Hence, users do not need any kind of knowledge to use the IOA.     

基于计算模型运用Civil3D实现路网场地整体优化的设计方法

提出基于条件极值的场地标高计算模型,采用该模型进行场地设计可实现地块与地块之间、地块与道路之间的土石方总体最优。通过工程实例介绍应用Civil3D实现该模型的场地设计方法,该方法效率较高,适用面较广,适合各种情况下的园区场地设计。     

Dynamic model for ride comfort evaluations of the rubber-tired light rail vehicle

The dynamic model was developed to evaluate vibration accelerations and ride comforts during the running of the Korean-standardised rubber-tired light rail vehicle. Ride comfort indexes were analysed and tested in accordance with UIC 513R by using the dynamic model and the actual vehicle in the test track. Based on the comparisons between analysis results and test results, the validity of the developed dynamic model was evaluated. It was verified whether or not the developed Korean-standardised rubber-tired light rail vehicle met the specified target specification on ride comfort. In addition, the influence of the wearing of guide wheels on ride comfort was estimated.     

An insight into linear quarter car model accuracy

The linear quarter car model is the most widely used suspension system model. A number of authors expressed doubts about the accuracy of the linear quarter car model in predicting the movement of a complex nonlinear suspension system. In this investigation, a quarter car rig, designed to mimic the popular MacPherson strut suspension system, is subject to narrowband excitation at a range of frequencies using a motor driven cam. Linear and nonlinear quarter car simulations of the rig are developed. Both isolated and operational testing techniques are used to characterise the individual suspension system components. Simulations carried out using the linear and nonlinear models are compared to measured data from the suspension test rig at selected excitation frequencies. Results show that the linear quarter car model provides a reasonable approximation of unsprung mass acceleration but significantly overpredicts sprung mass acceleration magnitude. The nonlinear simulation, featuring a trilinear shock absorber model and nonlinear tyre, produces results which are significantly more accurate than linear simulation results. The effect of tyre damping on the nonlinear model is also investigated for narrowband excitation. It is found to reduce the magnitude of unsprung mass acceleration peaks and contribute to an overall improvement in simulation accuracy.     

某出口米轨动车组(Tc车)车体设计及试验对比研究

介绍了使用大型通用计算机辅助工程软件ANSYS和有限元方法,对某出口米轨动车组(Tc车)进行了分析计算的过程,并通过实际物理样机试验数据与计算数据的比对,分析车身强度的可靠性。     

The train platforming problem: The infrastructure management company perspective

If railway companies ask for station capacity numbers, their underlying question is in fact one about the platformability of extra trains. Train platformability depends not only on the infrastructure, buffer times, and the desired departure and arrival times of the trains, but also on route durations, which depend on train speeds and lengths, as well as on conflicts between routes at any given time. We consider all these factors in this paper. We assume a current train set and a future one, where the second is based on the expected traffic increase through the station considered. The platforming problem is about assigning a platform to each train, together with suitable in- and out-routes. Route choices lead to different route durations and imply different in-route-begin and out-route-end times. Our module platforms the maximum possible weighted sum of trains in the current and future train set. The resulting number of trains can be seen as the realistic capacity consumption of the schedule. Our goal function allows for current trains to be preferably allocated to their current platforms.Our module is able to deal with real stations and train sets in a few seconds and has been fully integrated by Infrabel, the Belgian Infrastructure Management Company, in their application called Ocapi, which is now used to platform existing and projected train sets and to determine the capacity consumption.     

Mathematical properties and constraints representation for bottom-up approaches to the evaluation of GHG mitigation policies

Bottom-up models, including MARKAL, MESSAGE and AIM, are widely used when analyzing the effect of greenhouse gas (GHG) abatement policies. These bottom-up models are mostly formulated as a linear programming (LP) optimization model to find both the minimal cost combination of abatement technologies and energy flows while satisfying demands. It is not unusual that the bottom-up modeling involves a great number of technical, industrial, socioeconomic and environmental constraints. Investigating representative constraints needed for analyzing GHG abatement policies, this study proposes how to implement these constraints in bottom-up modeling.