编组站系统能力协调度的计算分析

以编组站实际作业过程为研究背景,基于编组站车流到达的不均衡性,将每一时段[ti-1,ti)的车流输入强度划分为3种不同的到达状态,结合对车流状态及编组站各系统能力的分析,得出编组站系统作业能力的协调度计算公式,最后,根据某编组站的实际车流量,计算出该编组站车流密集到达状态下的系统协调度。实例计算分析表明:所得出的协调度计算结果能够反映出编组站系统能力协调的薄弱环节,为提高编组站整体作业能力提供了一种新的方法。     

单周控制的单相静止无功发生器

提出了单周控制的单相静止无功发生器(SPSVG)的工作原理,利用单周控制形成的正弦脉宽调制SPWM,对其单相电压源逆变器进行控制,保证电流的正弦性,对SPSVG进行了建模以及开环、闭环控制的Matlab/Simulink的仿真,仿真结果证明在原理上可行。     

200km/h六轴大功率客运交流传动电力机车概述

介绍了200 km/h六轴大功率客运交流传动电力机车的主要技术特点、性能参数、总体结构,以及通风系统、电气系统、机械系统、制动系统等子系统的技术方案。     

主变压器差动保护装置极性问题的探讨

阐述牵引变电所三相V/v接线牵引变压器差动保护极性的影响因素及其校验方法（微机保护的极性、主变压器的极性和电流互感器的极性3方面）,分析了包西线某牵引变电所主变压器设计和接线的缺陷,提出并验证了三相V/v接线牵引变压器差动保护接线方式的正确性。     

利用钢轮托车辅助盾构机过站施工技术

针对地铁盾构法施工中盾构机通过满足过站要求的已完工车站进行二次始发这一常见施工环节,介绍一种通过钢轮托车辅助盾构机空载推进实现过站需要的施工技术及相应施工要点,如盾构机过站的施工工艺流程,钢板、钢轮拖车及轨道的铺设等。论述了利用钢轮拖车辅助盾构机过站施工技术采取的质量控制、安全措施及环保措施,分析了采用该技术的经济、社会和环境效益。     

变频器输出电压du/dt对电机的影响及其滤波器的设计

研究了变频器输出电压du/dt对电机端电压和轴承电流的影响,在PSpice中建立了电机高频模型,并对端电压波形进行了仿真;着重研究了一种du/dt滤波器的参数设计方法,并且进行了仿真和实验验证。实践证明,该滤波器具有较好的滤波效果。     

CARD/1系统在互通立交设计绘图上的应用与开发

通过对CARD/1系统在T型（Y型）互通式立体交叉设计绘图上的二次开发，使T型（Y型）互通式立体交叉的设计绘图达到一体化。     

旧水泥混凝土路面FWD实测数据的分析

基于某国道的FWD实测数据,分析FWD参数与旧水泥混凝土路面状况(现场调查实录及测试数据)间的某些相关性,探索旧水泥混凝土板的接缝传荷能力、弯曲刚度、综合承载能力等定性或定量的判别方法,提出利用FWD加载中心弯沉值总水平评价旧水泥混凝土路面综合承载能力的设想。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Experimental evaluation of Heavy Duty Vehicle speed patterns in urban and port areas and estimation of their fuel consumption and exhaust emissions

Exhaust emissions and fuel consumption of Heavy Duty Vehicles (HDVs) in urban and port areas were evaluated through a dedicated investigation. The HDV fleet composition and traffic driving from highways to the maritime port of Genoa and crossing the city were analysed. Typical urban trips linking highway exits to port gates and HDV mission profiles within the port area were defined. A validation was performed through on-board instrumentation to record HDV instantaneous speeds in urban and port zones. A statistical procedure enabled the building-up of representative speed patterns. High contrasts and specific driving conditions were observed in the port area. Representative speed profiles were then used to simulate fuel consumption and emissions for HDVs, using the Passenger car and Heavy duty Emission Model (PHEM). Complementary estimations were derived from Copert and HBEFA methodologies, allowing the comparison of different calculation approaches and scales. Finally, PHEM was implemented to assess the performances of EGR or SCR systems for NO_X reduction in urban driving and at very low speeds.The method and results of the investigation are presented. Fuel consumption and pollutant emission estimation through different methodologies are discussed, as well as the necessity of characterizing very local driving conditions for appropriate assessment.