软岩隧道三维扫描变形监测技术的试验研究

为解决传统监测技术单点监测无法满足软岩隧道整体性变形监测的局限性,采用三维激光扫描技术进行软岩隧道整体性变形监测试验,从隧道结构的变形时间、变形空间分布及变形量进行整体分析。首先建立全站仪和三维激光扫描仪测量误差模型,分析三维扫描监测技术与传统隧道监测技术的特点,通过平面标靶和棱镜靶球精度试验得出平面标靶最佳入射角范围小于60°,棱镜靶球自动提取距离不大于45 m,作为测站设置和控制点布设的依据; 然后以渭武高速木寨岭隧道2号斜井工程为依托,开展软岩隧道三维扫描变形监测技术的试验研究。研究结果表明： 中台阶开挖支护前已发生较大变形,最大变形位置为左侧上台阶与中台阶交界处,空间分布呈左大右小,试验段最大累计变形达0.48 m,下台阶及时封闭成环及2层初期支护有利于变形控制。     

大型地下空间的结构分割转换工法研究

为解决当下地下空间开发难题,依托中铁工程装备集团地下停车场项目,提出建造大型地下空间的结构分割转换工法（CC工法）,并成功应用。文章从传统各工法的特点出发,阐述CC工法的设想。基于工程实践过程,首先,从地下结构的分割与转换2个角度,重点介绍大型地下空间的形成过程、型钢和钢筋混凝土组合结构管节、节点处理措施等创新内容; 然后,针对B类节点的处理措施、整体背土现象等工程问题进行解决与优化; 最后,探讨该工法拓展应用的可能性,分别介绍多层、曲线、长距离、装配式结构大型地下空间的初步方案。CC工法的成功研发,旨在为城市大型地下空间开发提供一套新的解决思路。     

圭嘎拉高海拔隧道施工人员体力劳动强度评价

为探究圭嘎拉高海拔隧道施工人员体力劳动强度水平,评价施工工序劳动强度,选择圭嘎拉隧道进口段（海拔4 300 m）及1#斜井段（海拔4 560 m）的施工人员作为测试对象,分别测量不同工序下施工人员的生理指标（心率、血氧饱和度、耗氧量）。基于耗氧量计算能量代谢率,进而计算各工序的劳动强度指数。结果表明： 1）260 m的海拔高差造成的施工综合劳动强度指数差异具有统计学意义（P<0.05）; 2）二次衬砌钢筋绑扎是所测施工工序中劳动强度最大的工序,该工序下施工人员的心率、血氧饱和度和平均能量代谢率都出现超过卫生限值的情况,劳动强度指数达到35（极重）; 3）海拔为4 300~4 560 m时,隧道各施工工序劳动强度大部分为中度-极重度。     

丽香铁路黄山哨隧道下穿岩堆段设计施工关键技术

以下穿岩堆段的丽香铁路黄山哨隧道为工程依托,对岩堆段地表开裂及洞内初期支护边墙严重变形的问题进行研究。地表埋设6根测斜管监测地表位移情况,洞内布置3个断面进行围岩压力、钢架内力、二次衬砌内力、初期支护与二次衬砌间的接触压力、锚杆轴力量测。在分析现场岩堆段洞内外受力机制及原因的基础上,根据数值计算结果优化二次衬砌断面型式及进一步加大二次衬砌厚度及配筋。采取以下措施控制隧道岩堆段变形： 1）地表岩堆土石接触面开裂处增设截排水措施; 2）加大隧道初期支护钢架型号及加长岩堆侧边墙径向系统锚杆; 3）加大隧道边墙轮廓曲率并优化隧道二次衬砌型式为圆顺型; 4）隧道预留变形量加大至30 cm; 5）隧道二次衬砌内净空预留50 cm补强空间; 6）隧道拱部设置42小导管超前支护。现场岩堆段采取以上措施后已顺利施工通过,根据洞内外监测结果显示,结构在安全可控范围内。     

On Safety in Dismantling Temporary Strut of Super-large Tunnels with Double-layer Primary Support北大核心CSCD

More and more multiple-track tunnels and super-large section tunnels have been built, and disman- tling of temporary strut is a weak point of the whole structure during force transfer when the secondary lining is con- structed. It is significant to guarantee structure safety during dismantling of temporary strut. Little systematic re- search on safety in dismantling of temporary strut of the super-large section tunnel with double-layer primary support has been conducted, so the internal force and security of the two-layer primary support of the Xinkaotang tunnel were analyzed by a numerical analysis and site measurement, and it proves the effect of two-layer primary support on the safety during strut dismantling. The research results indicate that: (1) with constant support thickness and one-time longitudinal dismantling length, the safety factor of secondary primary support is larger than that of the first primary support, and the safety factor of the first primary support is larger than that of the single-layer primary support. Change range of safety factor for the first primary support is smaller than that of the single-layer primary support, and the safe factor for the single-layer primary support is smaller than that of the secondary primary support; (2) with the same support pattern, the safety factors increase firstly and then decrease with an increase of the onetime dismantling length. The calculated results of various cases show that the reasonable one-time dismantling length for this project is about 9 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Effect of Explosion in a Gas Pipeline Compartment of a Utility Tunnel on Neighboring Metro Tunnels北大核心CSCD

In this paper the numerical simulation analysis of the effect of explosion in the gas pipeline compartment of a utility tunnel on neighboring metro tunnels was conducted using the software AUTODYN. The results show that the TNT equivalent in a fireproof partition with length of 200 m is 41.6 kg when the gas concentration in the gas pipeline compartment reaches 10%; the blast wave has much effect on the crown and arch waist of the round metro tunnel and it’s necessary to take some protective measures in both areas; when the surrounding soil is sand, the utili- ty tunnel is above the round metro tunnel and their alignments are in the same direction, the greater the vertical spacing between the utility tunnel and the metro tunnel, the smaller the effect of the blast wave on the metro tunnel; when the vertical spacing is 7.2 m, the maximum dynamic tensile stress is 1.86 MPa (including the static stress value of 1 MPa in the tunnel segment) and it is slightly smaller than the designed tensile strength of metro tunnel (about 1.89 MPa). The maximum vibration velocity and the maximum displacement meet the structural stability require- ments, so it is suggested the vertical spacing between the utility tunnel and metro tunnel shall not be less than 7.2 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Characteristics and Development Trends of the Support Technology of High Ground Stress Tunnels in China北大核心CSCD

Combining the present situation and development trend of different tunnel support technologies at home and abroad, this paper analyzes the problems of rockburst in hard rock tunnels and large deformation in soft rock tunnels caused by high ground stress. It is concluded that: 1) regarding the rockburst problem, the current support technology is mainly influenced by the rock burst mechanism which is dominated by static factors, and so the used support components are generally of smaller deformation performance and "passive support" properties; 2) as the rockburst is the result of dynamic-static stress coupling, and only the anchor bolt has the "active support" attribute in the current "shotcrete+anchor bolt+wire net" support system, so the best support system should have the two functions of active support and energy release in terms of the rockburst problem, and the key focus of the research and development is anchorage members; 3) there are three main support types for large deformation in soft rock tunnels, e.g. the heavy support, layered support and yielding support. Among them, the heavy support system in underground cavern with large deformation is easy to induce excessive surrounding rock pressure, and so the applicable conditions are limited. The layered support system is still not the best choice due to its immature theoretical study, difficult determination of the thickness value and the installation time of each support layer and the interference to construction progress. With the characteristics of timely support and yielding while supporting, the yielding support system can give full play to the performance values of surrounding rocks and supporting materials, and make both of them reach the optimal state, so it is the best choice for supporting the soft rock tunnels with large deformations. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Soil Body Deformation Caused by Construction of a Double-Line Shield Tunnel with Multiple Factors北大核心CSCD

Considering the influence of many factors (soil loss, frontal additional thrust, the friction force of the shield shell and the additional grouting force), a method for improving the uniform soil body movement model is pro-posed, and a mechanical calculation model is established to study the calculation method for soil body deformation caused by double-line parallel shield driving. Based on the Mindlin solutions of elastic mechanics, the theoretical solutions for soil body deformations caused by the last three factors are calculated; considering the uniform soil body movement model, the theoretical solutions for soil body deformations caused by soil loss are calculated, then the to-tal theoretical solutions for soil body deformations under multiple factors are obtained by means of superposition. The vertical surface settlement, vertical horizontal displacement, and vertical displacements of the soil body at different depths of Hangzhou Metro Line 1 are calculated to analyze the variation laws. Meanwhile the influential factors for horizontal displacement variation are studied. The research shows that with a change of depth, the settlement of the soil body changes within the scope of 10 to 13 m in the horizontal direction near where the maximum settlement occurs;the direction of the horizontal displacement of the soil body changes with a change of the positional relationship be-tween the calculation points and the tunnel; and with an increase of interval J for the two tunnels, the horizontal dis-placement of the soil body of a deep double-line tunnel decreases while the displacement near the surface changes slightly. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

不同冷却方式对大尺寸钢板感应加热成形的影响

为有效解决船用中厚钢板复杂曲面加工问题,本文探究了空气冷却、正面水冷和反面水冷方式对大尺寸钢板弯曲成型的影响因素。首先采用COMSOL Multiphysics仿真平台模拟了电磁感应加热和冷却变形多物理场同步耦合过程,然后分析了各种因素对大尺寸钢板弯曲成型影响,最后通过实验验证了有限元模型的可靠性,并对感应加热弯曲成型效果进行评估。研究结果表明:(1)相对于水冷,空冷对钢板Y向位移改变效果显著。(2)相对于空冷,水冷对钢板角位移的改变影响明显。(3)当频率为50kHz时,电流频率对表面温度和角位移影响显著。(4)当钢板长宽比≥1:2时,Y向位移的增加比较显著;当长宽比≈1:1时,角位移的改变比较明显。