A receding horizon sliding control approach for electric powertrains with backlash and flexible half-shafts

Active control of electric powertrains is challenging, due to the fact that backlash and structural flexibility in transmission components can cause severe performance degradation or even instability of the control system. Furthermore, high impact forces in transmissions reduce driving comfort and possibly lead to damage of the mechanical elements in contact. In this paper, a nonlinear electric powertrain is modelled as a piecewise affine (PWA) system. The novel receding horizon sliding control (RHSC) idea is extended to constrained PWA systems and utilised to systematically address the active control problem for electric powertrains. Simulations are conducted in Matlab/Simulink in conjunction with the high fidelity Carsim software. RHSC shows superior jerk suppression and target wheel speed tracking performance as well as reduced computational cost over classical model predictive control (MPC). This indicates the newly proposed RHSC is an effective method to address the active control problem for electric powertrains.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

超高压共轨系统轨压控制策略研究

为稳定控制超高压共轨系统中的共轨腔压力并缩短轨压控制算法的开发周期,利用AMESim/Simulink联合仿真技术建立了超高压共轨系统轨压控制仿真模型,采取前馈+PID控制算法设计了轨压控制策略,并针对轨压控制中的瞬态和稳态工况进行了仿真计算,最后在试验台架上开展了轨压跟随性测试。结果表明:所制定的前馈+PID控制算法能使轨压稳定在目标轨压附近,上下波动小于3 MPa,且轨压突变时瞬态响应时间小于0.5s,控制结果能够满足超高压共轨系统对精度和速度的需求。     

面向控制的SCR催化转化器温度模型

为了建立面向控制的SCR催化器温度模型,根据能量守恒和质量守恒方程并考虑热平衡中所涉及的换热过程不同,建立了4种SCR催化器温度的数学模型,并利用Matlab/Simulink构建图形化的计算模型。采用柴油机欧洲稳态循环(ESC)和欧洲瞬态循环(ETC)条件下的台架实测数据对模型进行检验,基于最大离散程度、拟合度和计算时间3个指标对模型进行评价和比较。结果表明,考虑催化器与废气和周围环境对流换热的温度模型具有良好的预测精度和实时性,更适合用于SCR控制策略。     

现代大学生公寓电气设计浅析

文章采用文献资料、归纳与综合、专家访谈等研究方法,对现代大学生公寓电气设计进行了系统研究,主要内容包括配电系统、负荷系统、防雷接地、消防系统和智能化五个方面,旨为大学生公寓的电气设计提供有益资讯．     

“学-导多元互动”教学模式对高校艺术设计教育的启示——以视觉传达设计教学为例

“学-导多元互动”教学模式是依据相关教育理论、教育观念以及结合现代远程开放教育发展的要求和实践而形成的重在体现以人为本,真正做到“以学习者为中心”,为学习者提供多元的服务,满足学习者的学习需要和求知愿望,构建终身学习体系和学习型社会的教育思想的教学模式。文章以视觉传达设计教学为例,从“学-导多元互动”教学模式的内涵、教学效果及对高校艺术设计教育的启示三个方面加以阐述,希望对于高校艺术设计教育教学模式的改革起到一些借鉴作用。     

高校图书馆的人力资源管理略论

文章分析了当前高校图书馆人力资源管理存在的问题,对加强人力资源管理的必要性提出了看法,并就加强人力资源管理的有效途径进行了探讨。     

桥梁加宽中新增梁对旧桥的影响

依托黄土地区高速公路改扩建桥梁加宽工程,选取一座3孔13 m简支空心板桥,分析新增空心板梁对旧桥原有板梁的影响。基于不同加宽方案对新旧桥空心板梁横向分布系数进行了计算,计算结果表明增加新梁截面刚度可有效降低旧梁横向分布系数。建议采用移旧桥边梁为新桥边梁并且提高新增空心板梁刚度的加宽方案。     

信息化战争交通重点目标防护的对策

针对信息化战争条件下战场透明化和打击精确化的特点,从建立和完善"综合集成" 的防护体系、完善伪装防护技术手段、适时做好交通保障器材的储备和更新等方面,提出了交通重点目标防护应采取的技术措施和应对精确打击的相关对策.