非完整力学系统中Hamilton原理应用中的问题

本文从数学推演、力学系统运动的初值问题的提法和变分原理的基本要求这三个方面论述了 Hamilton 变分原理不适用于非完整力学系统。     

焊接钢梁疲劳寿命及其参数研究

焊接钢构件的概率疲劳寿命曲线和概率裂纹扩展速率曲线是进行钢结构疲劳可靠性设计和服役期间剩余疲劳寿命可靠性评估所必须的。为了获得一些构件的概率曲线,对美国NCHRP研究机构所进行的大规模焊接钢梁疲劳试验结果进行再分析。通过原始数据的统计检验,得出了常见构件的全寿命概率分布。根据Paris公式及已有的结论,对原始数据进行推演再分析,获得了Paris公式中参数的概率分布。最后,给出了概率断裂力学方法预测焊接钢梁在给定可靠度下疲劳裂纹扩展寿命的算例。     

基于统一的疲劳寿命预报方法（UFLP）的深潜器载人舱疲劳可靠性分析

疲劳是承受循环载荷的金属结构最重要的失效机制,现已有多种金属疲劳寿命预报方法。实际的设计、制造、加工和操作等工序环节中总是存在不确定性,这些不确定性的影响将在结构的疲劳寿命中富集,为此发展了疲劳可靠性分析。该文讨论了将疲劳可靠性分析方法和统一的疲劳寿命预报方法（UFLP）相结合的可行性,为海洋结构物的安全使用提供参考。文中的极限状态方程是基于统一的疲劳寿命预报方法（UFLP）得到的,并讨论了其中各参数对疲劳寿命的影响;针对一组TC4-ELI的疲劳裂纹扩展数据,分别采用Monte-Carlo法和JC法开展了疲劳可靠性分析,两种分析方法得到的结果彼此符合得较好。     

某型船锁气室通风量设计研究

文章通过模型试验结合工程分析的方法,提出一套对锁气室风量设计优化选择的流程。建立1∶1的锁气室模型,对不同风量下污染物变化情况进行试验,初步获得各风量下浓度变化情况。在试验的数据基础上,结合工程实际情况,从造价因素、安装因素和人员流动三个方面进行分析,选择实船适用的风量。     

Mathematical model for optimising the sequence for clearing snow from the manoeuvring area during winter operations

This article considers the optimisation of the sequence for clearing snow from stretches of the manoeuvring area of an airport. This issue involves the optimisation of limited resources to remove snow from taxiways and runways thereby leaving them in an acceptable condition for operating aircraft. The airfield is divided into subsets of significant stretches for the purpose of operations and target times are established during which these are open to aircraft traffic. The document contains several mathematical models each with different functions, such as the end time of the process, the sum of the end times of each stretch and gap between the estimated and the real end times. During this process, we introduce different operating restrictions on partial fulfilment of the operational targets as applied to zones of special interest, or relating to the operation of the snow‐clearing machines. The problem is solved by optimisation based on linear programming. The article gives the results of the computational tests carried out on five distinct models of the manoeuvring area, which cover increasingly complex situations and larger areas. The mathematical model is particularised for the case of the manoeuvring area of Adolfo Suarez Madrid—Barajas Airport. Copyright © 2016 John Wiley & Sons, Ltd.

Highlights
• Optimal sequence for clearing snow from the manoeuvring area of an airport.
• Contains optimising algorithms solved using CPLEX LP‐based tree search.
• Restrictions on partial fulfilment of operational targets applied to subsets of significant stretches, used for planning the operation of snow‐clearing machines.
• Model applied to the case of the manoeuvring area of Adolfo Suárez Madrid Barajas Airport.
• Conclusions are given on the results of the computational tests carried out. There are five models of the manoeuvring area which cover increasingly complex situations and larger areas.

     

A survey of wheel–rail contact models for rail vehicles

Accurate and efficient contact models for wheel–rail interaction are essential for the study of the dynamic behaviour of a railway vehicle. Assessment of the contact forces and moments, as well as contact geometry provide a fundamental foundation for such tasks as design of braking and traction control systems, prediction of wheel and rail wear, and evaluation of ride safety and comfort. This paper discusses the evolution and the current state of the theories for solving the wheel–rail contact problem for rolling stock. The well-known theories for modelling both normal contact (Hertzian and non-Hertzian) and tangential contact (Kalker's linear theory, FASTSIM, CONTACT, Polach's theory, etc.) are reviewed. The paper discusses the simplifying assumptions for developing these models and compares their functionality. The experimental studies for evaluation of contact models are also reviewed. This paper concludes with discussing open areas in contact mechanics that require further research for developing better models to represent the wheel–rail interaction.     

水泥路面板高温隆起的力学机理分析

为了避免或延缓水泥路面板在夏季产生高温隆起现象,从力学机理的角度,探讨了水泥路面板在夏季高温隆起的原因,并举例计算水泥路面板板顶与板底全年最大的应力差及水泥路面板压曲临界应力。结果表明,仅从强度的角度来看,如胀缝设置不当,则旧水泥路面板在夏季都是危险的;如果胀缝功能得不到保证,厚度26 cm左右的水泥路面板,在夏季出现隆起的临界板长约为85 m。因此,建议在南方地区,对于4级及4级以下公路(特别是低造价的农村公路)广泛采用的素混凝土或低配筋混凝土路面,胀缝按80 m间距来设置是适宜的。     

波形钢腹板组合箱梁弹性阶段弯曲理论及模型试验研究

基于波形钢腹板组合箱梁独特的受力特点,建立了系统的弹性阶段受弯分析理论：从弯曲正应变分布的拟平截面假定出发,采用材料力学方法,推导了正应力、剪应力及波形钢腹板承担的剪力占整个截面所受剪力比例的计算公式;运用能量原理推导了挠度的计算公式。分析表明：在完全忽略波形钢腹板弯曲刚度的情况下,其剪应力沿梁高是不变的;波形钢腹板承担的剪力比例一般在80％以上;在设计常用的高跨比下,波形腹板剪切变形引起的挠度不可忽略。在此基础上,进行了1根模型梁的试验研究,理论分析值与试验结果、空间有限元计算值吻合良好,说明本文理论公式可以在设计中应用。     

Transport of radionuclides by sea-ice and dense-water formed in western Kara Sea flaw leads

A transport assessment of particle-bound and dissolved artificial radionuclides (¹³⁷Cs and ^239,240Pu) by sea-ice and dense-water formed in western Kara Sea flaw leads close to the Novaya Zemlya dumping sites is presented in this study. We both performed a “best estimate” based on available data, and a “maximum assessment” relying on simulated constant releases of 1 TBq ¹³⁷Cs and ^239,240Pu from individual dumping bays. The estimates are based on a combination of (i) the content of particulate matter in sea-ice; (ii) analytical data and numerical simulations of radionuclide concentrations in shelf surface deposits, suspended particulate matter (SPM), and the dissolved phase; and (iii) estimates of lead-ice and dense-water formation rates as well as modeling results of local ice drift pathways. In the “best estimate” case, 2.90 GBq ¹³⁷Cs and 0.51 GBq ^239,240Pu attached to sea-ice sediments can be exported from the lead areas toward the central Arctic basin. The radionuclide burden of the annually formed dense lead water in the “best estimate” amounts to 4.68 TBq ¹³⁷Cs and 0.014 TBq ^239,240Pu. In the “maximum assessment”, potential export-rates of ice-particle bound ¹³⁷Cs and ^239,240Pu toward the central Arctic would amount to 0.64 and 0.16 TBq, respectively. As much as ≈900 TBq ¹³⁷Cs and ≈6.75 TBq ^239,240Pu could be annually taken up by 34.75 dense-water rejected in the lead area. Assuming the (unlikely) instantaneous release of the total ¹³⁷Cs and ^239,240Pu inventories (≈1 PBq and 10 TBq, respectively) from the Novaya Zemlya dumping sites into the dissolved phase, the dense lead water locally formed during one winter season could take up ≈90% of the Cs and ≈68% of the Pu released.     

Flexural fatigue behavior of butt-welded circular concrete-filled double skin steel tube (CFDST)：Experimental study and numerical modeling

Detailed understandings on the fatigue behavior of the concrete-filled double skin steel tubes (CFDSTs) under multiaxial stress states are essential to promote their applications in marine structures. A systematical investigation consisting both the experimental study and the according numerical modeling has been conducted. Physical tests were carried out to investigate the flexural fatigue behavior of the butt-welded hollow steel tubes (HSTs), concrete-filled steel tubes (CFSTs) and CFDSTs, in which the development of fatigue cracks and the fatigue life were captured. The feasibility of applying the existing S–N curves originally obtained from the HSTs to the constitutive steel tubes within the CFDSTs has been consequently verified. A two-stages simulation method was developed to analyze the full range development of fatigue cracks based on both the damage mechanics and the extended finite element method (XFEM). The influence of the multiaxial stress states on the fatigue behavior for the constitutive steel tubes was studied quantitatively, considering the offshore application scenarios where the steel tubes within the CFDSTs were subjected to larger external hydrostatic pressure or internal transmitted content pressure. The results show that the existence of the infilled concrete can effectively improve the fatigue behavior of the steel tubes. The life prediction models for both the fatigue crack initiation stage and propagation stage have been proposed, where the crack initiation life of the steel tube may reduce by 30% when its stress triaxiality increases from 0.36 to 0.48.