技术站间货物列车协同配流方案研究

技术站间货物列车协同作业组织模式，可实现各站获益，整体加强，对提升铁路运输生产效率具有重要意义.本文建立技术站间货物列车协同配流模型.模型以最大化两技术站的正点出发列车数作为目标函数，采用启发式遗传算法进行寻优，得到货物列车解编顺序和配流方案.最后，通过对算例进行实验分析，验证协同配流模型的实用性.结果表明，技术站间协同配流作业明显压缩车辆在站总停留时间，增加了阶段计划内正点出发列车数，进而提高了技术站内线路使用能力.     

Modeling free-flow speed according to different water depths—From the viewpoint of dynamic hydraulic pressure

In this paper, we propose a method of modeling free flow speed from the viewpoint of hydroplaning. First, the lift forces for different water depths were estimated using Bernoulli’s equation. Compared with the result of the experimental test performed by the Japan Automobile Research Institute, the hydrodynamic pressure coefficient was determined to be 0.03 (tf s²/m⁴). The validation of the predicted lift force is found in another published paper. A very good match is found between the computed values by the proposed numerical model and the data in other published papers. Then, the loss of contact force is considered to evaluate the hydroplaning performance of a tire. To simulate the hydroplaning speed, a tire-sliding model was utilized to obtain the traction and friction forces between the road surface and the tire. The observation data obtained in Japan in 2009 is compared with the physically computed hydroplaning speed, yielding the conclusion that the traction force at the measured desired speed is, on average, 23.4% of the traction force at hydroplaning speed. The analytical model offers a useful tool to quantitatively show that the free flow speed changes as the water depth increase.     

基于客流需求的城市轨道交通动态时刻表优化模型

为使城市轨道交通列车运行时刻表更贴合客流需求,依据不断变化的客流需求确定每列车的发车时刻和停站时间,采用多目标优化方法构建以乘客出行时间费用和列车运行时间费用最小为目标、列车发车时刻和停站时间为决策变量的城市轨道交通动态时刻表优化模型,并采用粒子群算法求解。以广州地铁13号线为例进行验证,结果表明优化后的时刻表更满足客流需求,能有效地提高乘客出行效率,具有更好的动态适应性。     

共享停车泊位数量可变下交通流逐日演化规律

为了揭示在共享停车泊位数量可变条件下的网络交通流逐日演化规律,首先构建了共享泊位交易系统,并考虑了交易市场中的共享泊位提供者可以选择2种异质性的价格预期方式,即理性预期方式和幼稚预期方式;而后对共享泊位的均衡价格、2种提供者的占比差、高峰时段公交和小汽车需求的演化规律进行了分析;其次,以2条平行路径的路网为例,对网络交通流量分配的最终演化结果进行了分析;最后,在对上述2个系统的最终演化状态给出定量判据后,以北京市实际路网为例进行了数值试验。理论分析和数值试验结果表明:①对于共享泊位交易系统,若供给曲线斜率小于需求曲线斜率,则共享泊位交易系统的唯一均衡解可实现无条件渐进稳定;否则若理性提供者的交易与预测成本之和大于幼稚提供者,则存在临界提供者选择强度,使得共享泊位交易系统在大于此临界值条件下出现分岔或混沌现象;②对于网络交通流系统,若出行成本对路径流量敏感度小,路径选择概率对出行成本敏感度小,小汽车需求量不大,则系统唯一的均衡解可能是渐进稳定的,否则系统会出现分岔或混沌状态;③当共享泊位交易系统处于渐进稳定状态时,若提供者对共享泊位的价格变动不敏感,用户对其价格变动敏感,潜在共享泊位需求量不大,理性提供者的交易与预测成本之和并非远大于幼稚提供者,提供者选择强度不大,则由于受到共享泊位交易总量的限制,高峰时段的均衡小汽车需求不大,导致网络交通流系统的最终演化状态容易趋向于渐进稳定;④当共享泊位交易系统处于混沌状态时,网络交通流系统会产生更加严重的分岔与混沌现象。     

The identification and empirical characterization of vehicular (Lagrangian) fundamental diagrams in multilane traffic flow

Traditional macroscopic traffic flow modeling framework adopts the spatial–temporal coordinate system to analyze traffic flow dynamics. With such modeling and analysis paradigm, complications arise for traffic flow data collected from mobile sensors such as probe vehicles equipped with mobile phones, Bluetooth, and Global Positioning System devices. The vehicle‐based measurement technologies call for new modeling thoughts that address the unique features of moving measurements and explore their full potential. In this paper, we look into the concept of vehicular fundamental diagram (VFD) and discuss its engineering implications. VFD corresponds to a conventional fundamental diagram (FD) in the kinematic wave (KW) theory that adopts space–time coordinates. Similar to the regular FD in the KW theory, VFD encapsulates all traffic flow dynamics. In this paper, to demonstrate the full potential of VFD in interpreting multilane traffic flow dynamics, we generalize the classical Edie's formula and propose a direct approach of reconstructing VFD from traffic measurements in the vehicular coordinates. A smoothing algorithm is proposed to effectively reduce the nonphysical fluctuation of traffic states calculated from multilane vehicle trajectories. As an example, we apply the proposed methodology to explore the next‐generation simulation datasets and identify the existence and forms of shock waves in different coordinate systems. Our findings provide empirical justifications and further insight for the Lagrangian traffic flow theory and models when applied in practice. Copyright © 2015 John Wiley & Sons, Ltd.     

Life cycle assessment of heated apron pavement system operations

Heated pavement systems (HPS) offer an attractive alternative to the cumbersome process of removing ice and snow from airport pavements using traditional snow removal systems. Although snow and ice removing efficiency and economic benefits of HPS have been assessed by previous studies, their environmental impact is not well known. Airport facilities offering public or private services need to evaluate the energy consumption and global warming potential of different types of snow and ice removal systems. Energy usage and emissions from the operations of hydronic heated pavement system using geothermal energy (HHPS-G), hydronic HPS using natural gas furnace (HHPS-NG), electrically heated pavement system (EHPS), and traditional snow and ice removal system (TSRS) are estimated and compared in this study using a hybrid life cycle assessment (LCA). Based on the system models assessed in this study, HPS application in the apron area seems to be a viable option from an energy or environmental perspective to achieve ice/snow free pavement surfaces without using mechanical or chemical methods. TSRS methods typically require more energy and they produce more greenhouse gas (GHG) emissions compared to HPS during the operation phase, under the conditions and assumptions considered in this study. Also, HPS operations require less energy and have less GHG emissions during a snow event with a smaller snowfall rate and a larger snow duration.     

A comparative life-cycle energy and emissions analysis for intercity passenger transportation in the U.S. by aviation,intercity bus,and automobile

Intercity passenger trips constitute a significant source of energy consumption, greenhouse gas emissions, and criteria pollutant emissions. The most commonly used city-to-city modes in the United States include aircraft, intercity bus, and automobile. This study applies state-of-the-practice models to assess life-cycle fuel consumption and pollutant emissions for intercity trips via aircraft, intercity bus, and automobile. The analyses compare the fuel and emissions impacts of different travel mode scenarios for intercity trips ranging from 200 to 1600 km. Because these modes operate differently with respect to engine technology, fuel type, and vehicle capacity, the modeling techniques and modeling boundaries vary significantly across modes. For aviation systems, much of the energy and emissions are associated with auxiliary equipment activities, infrastructure power supply, and terminal activities, in addition to the vehicle operations between origin/destination. Furthermore, one should not ignore the embodied energy and initial emissions from the manufacturing of the vehicles, and the construction of airports, bus stations, highways and parking lots. Passenger loading factors and travel distances also significantly influence fuel and emissions results on a per-traveler basis. The results show intercity bus is generally the most fuel-efficient mode and produced the lowest per-passenger-trip emissions for the entire range of trip distances examined. Aviation is not a fuel-efficient mode for short trips (<500 km), primarily due to the large energy impacts associated with takeoff and landing, and to some extent from the emissions of ground support equipment associated with any trip distance. However, aviation is more energy efficient and produces less emissions per-passenger-trip than low-occupancy automobiles for trip distances longer than 700–800 km. This study will help inform policy makers and transportation system operators about how differently each intercity system perform across all activities, and provides a basis for future policies designed to encourage mode shifts by range of service. The estimation procedures used in this study can serve as a reference for future analyses of transportation scenarios.     

Including congestion effects in urban road traffic CO2 emissions modelling: Do Local Government Authorities have the right options?

Tailpipe emissions from vehicles on urban road networks have damaging impacts, with the problem exacerbated by the common occurrence of congestion. This article focuses on carbon dioxide because it is the largest constituent of road traffic greenhouse gas emissions. Local Government Authorities (LGAs) are typically responsible for facilitating mitigation of these emissions, and critical to this task is the ability to assess the impact of transport interventions on road traffic emissions for a whole network.This article presents a contemporary review of literature concerning road traffic data and its use by LGAs in emissions models (EMs). Emphasis on the practicalities of using data readily available to LGAs to estimate network level emissions and inform effective policy is a relatively new research area, and this article summarises achievements so far. Results of the literature review indicate that readily available data are aggregated at traffic level rather than disaggregated at individual vehicle level. Hence, a hypothesis is put forward that optimal EM complexity is one using traffic variables as inputs, allowing LGAs to capture the influence of congestion whilst avoiding the complexity of detailed EMs that estimate emissions at vehicle level.Existing methodologies for estimating network emissions based on traffic variables typically have limitations. Conclusions are that LGAs do not necessarily have the right options, and that more research in this domain is required, both to quantify accuracy and to further develop EMs that explicitly include congestion, whilst remaining within LGA resource constraints.     

Greenhouse gas emissions from road construction: An assessment of alternative staging approaches

The greenhouse gas (GHG) emissions associated with road construction activities are analyzed. The main focus of this analysis is on the vehicle emissions associated with alternative project staging approaches, specifically a full closure of the road during construction, versus an intermittent road closure. The analysis includes the direct and upstream emissions associated with materials, construction equipment, mobilization of resources to the work site, and maintenance activity associated with the project over its lifetime. The analysis is based on one case study of a road project in New Jersey. The assumptions underlying the staging analysis are based on hypothetical approaches. Results provide an assessment of the main sources of project related emissions and the ability to minimize total project emissions by minimizing traffic disruption. In the analysis with a full closure of the road, traffic disruption accounts for 26% of total emissions, while with an intermittent road closure, traffic disruption accounts for only 2% of total emissions. The other main sources are from materials and life-cycle maintenance. The analysis demonstrates the feasibility of minimizing project related GHG emissions during road construction activities.     

Strain prediction for critical positions of FPSO under different loading of stored oil using GAIFOA-BP neural network

FPSO (floating, production, storage and offloading) units are widely used in the offshore oil and gas industry. Generally, FPSOs have excellent oil storage capacity owing to their huge oil cargo holds. The volume and distribution of stored oil in the cargo holds influence the strain level of hull girder, especially at critical positions of FPSO. However, strain prediction using structural analysis tools is computationally expensive and time consuming. In this study, a prediction tool based on back-propagation (BP) neural network called GAIFOA-BP is proposed to predict the strain values of concerned positions of an FPSO model under different oil storage conditions. The GAIFOA-BP combines BP model and GAIFOA which is a combination of genetic algorithm (GA) and an improved fruit fly optimization algorithm (IFOA). Results from three benchmark tests show that the GAIFOA-BP model has a remarkable performance. Subsequently, a total of 81 sets of training data and 25 sets of testing data are obtained from experiment using fiber Bragg grating (FBG) sensors installed on the surface of an FPSO model. The numerical results show that the GAIFOA-BP is capable of predicting the strain values with higher accuracy as compared with other BP models. Finally, the reserved GAIFOA-BP model is utilized to predict the strain values under the inputs of a 10-day time series of volume and distribution of stored oil. The predicted strain results are further used to calculate the fatigue consumption of measurement points.