Closed-form multiclass cell transmission model enhanced with overtaking,lane-changing,and first-in first-out properties

A novel multiclass macroscopic model is proposed in this article. In order to enhance first-in, first-out property (FIFO) and transmission function in the multiclass traffic modeling, a new multiclass cell transmission model with FIFO property (herein called FM-CTM) is extended from its prior multiclass cell transmission model (M-CTM). Also, to enhance its analytical compactness and resultant computational convenience, FM-CTM is formulated in this paper as a set of closed-form matrix equations. The objective is to improve the accuracy of traffic state estimation by enforcing FIFO property when a fast vehicle cannot overtake a slow vehicle due to a limitation of a single-lane road. Moreover, the proposed model takes into account a different priority for vehicles of each class to move forward through congested road conditions, and that makes the flow calculation independent from their free-flow speeds. Some hypothetical and real-world freeway networks with a constant or varying number of lanes are selected to verify FM-CTM by comparing with M-CTM and the conventional CTM. Observed densities of VISSIM and real-world dataset of I-80 are selected to compare with the simulated densities from the three CTMs. The numerical results show that FM-CTM outperforms the other two models by 15% of accuracy measures in most cases. Therefore, the proposed model is expected to be well applicable to the road network with a mixed traffic and varying number of lanes.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

Planning hierarchical urban transit systems for reductions in greenhouse gas emissions

Public transit systems with high occupancy can reduce greenhouse gas (GHG) emissions relative to low-occupancy transportation modes, but current transit systems have not been designed to reduce environmental impacts. This motivates the study of the benefits of design and operational approaches for reducing the environmental impacts of transit systems. For example, transit agencies may replace level-of-service (LOS) by vehicle miles traveled (VMT) as a criterion in evaluating design and operational changes. In previous work, we explored the unintended consequences of lowering transit LOS on emissions in a single-technology transit system. Herein, we extend the analysis to account for a more realistic case: a transit system with a hierarchical structure (trunk and feeder lines) providing service to a city where demand is elastic. By considering the interactions between the trunk and the feeder systems, we provide a quantitative basis for designing and operating integrated urban transit systems that can reduce GHG emissions and societal costs. We find that highly elastic transit demand may cancel emission reduction potentials resulting from lowering LOS, due to demand shifts to lower occupancy vehicles. However, for mass transit modes, these potentials are still significant. Transit networks with buses, bus rapid transit or light rail as trunk modes should be designed and operated near the cost-optimal point when the demand is highly elastic, while this is not required for metro. We find that the potential for unintended consequences increases with the size of the city. Our results are robust to uncertainties in the costs and emissions parameters.     

Model based urban traffic control,part II: Coordinated model predictive controllers

The present paper describes how to use coordination between neighbouring intersections in order to improve the performance of urban traffic controllers. Both the local MPC (LMPC) introduced in the companion paper (Hao et al., 2018) and the coordinated MPC (CMPC) introduced in this paper use the urban cell transmission model (UCTM) (Hao et al., 2018) in order to predict the average delay of vehicles in the upstream links of each intersection, for different scenarios of switching times of the traffic lights at that intersection. The feedback controller selects the next switching times of the traffic light corresponding to the shortest predicted average delay. While the local MPC (Hao et al., 2018) only uses local measurements of traffic in the links connected to the intersection in comparing the performance of different scenarios, the CMPC approach improves the accuracy of the performance predictions by allowing a control agent to exchange information about planned switching times with control agents at all neighbouring intersections. Compared to local MPC the offline information on average flow rates from neighbouring intersections is replaced in coordinated MPC by additional online information on when the neighbouring intersections plan to send vehicles to the intersection under control. To achieve good coordination planned switching times should not change too often, hence a cost for changing planned schedules from one decision time to the next decision time is added to the cost function. In order to improve the stability properties of CMPC a prediction of the sum of squared queue sizes is used whenever some downstream queues of an intersection become too long. Only scenarios that decrease this sum of squares of local queues are considered for possible implementation. This stabilization criterion is shown experimentally to further improve the performance of our controller. In particular it leads to a significant reduction of the queues that build up at the edges of the traffic region under control. We compare via simulation the average delay of vehicles travelling on a simple 4 by 4 Manhattan grid, for traffic lights with pre-timed control, traffic lights using the local MPC controller (Hao et al., 2018), and coordinated MPC (with and without the stabilizing condition). These simulations show that the proposed CMPC achieves a significant reduction in delay for different traffic conditions in comparison to these other strategies.     

Life cycle assessment of heated apron pavement system operations

Heated pavement systems (HPS) offer an attractive alternative to the cumbersome process of removing ice and snow from airport pavements using traditional snow removal systems. Although snow and ice removing efficiency and economic benefits of HPS have been assessed by previous studies, their environmental impact is not well known. Airport facilities offering public or private services need to evaluate the energy consumption and global warming potential of different types of snow and ice removal systems. Energy usage and emissions from the operations of hydronic heated pavement system using geothermal energy (HHPS-G), hydronic HPS using natural gas furnace (HHPS-NG), electrically heated pavement system (EHPS), and traditional snow and ice removal system (TSRS) are estimated and compared in this study using a hybrid life cycle assessment (LCA). Based on the system models assessed in this study, HPS application in the apron area seems to be a viable option from an energy or environmental perspective to achieve ice/snow free pavement surfaces without using mechanical or chemical methods. TSRS methods typically require more energy and they produce more greenhouse gas (GHG) emissions compared to HPS during the operation phase, under the conditions and assumptions considered in this study. Also, HPS operations require less energy and have less GHG emissions during a snow event with a smaller snowfall rate and a larger snow duration.     

A comparative life-cycle energy and emissions analysis for intercity passenger transportation in the U.S. by aviation,intercity bus,and automobile

Intercity passenger trips constitute a significant source of energy consumption, greenhouse gas emissions, and criteria pollutant emissions. The most commonly used city-to-city modes in the United States include aircraft, intercity bus, and automobile. This study applies state-of-the-practice models to assess life-cycle fuel consumption and pollutant emissions for intercity trips via aircraft, intercity bus, and automobile. The analyses compare the fuel and emissions impacts of different travel mode scenarios for intercity trips ranging from 200 to 1600 km. Because these modes operate differently with respect to engine technology, fuel type, and vehicle capacity, the modeling techniques and modeling boundaries vary significantly across modes. For aviation systems, much of the energy and emissions are associated with auxiliary equipment activities, infrastructure power supply, and terminal activities, in addition to the vehicle operations between origin/destination. Furthermore, one should not ignore the embodied energy and initial emissions from the manufacturing of the vehicles, and the construction of airports, bus stations, highways and parking lots. Passenger loading factors and travel distances also significantly influence fuel and emissions results on a per-traveler basis. The results show intercity bus is generally the most fuel-efficient mode and produced the lowest per-passenger-trip emissions for the entire range of trip distances examined. Aviation is not a fuel-efficient mode for short trips (<500 km), primarily due to the large energy impacts associated with takeoff and landing, and to some extent from the emissions of ground support equipment associated with any trip distance. However, aviation is more energy efficient and produces less emissions per-passenger-trip than low-occupancy automobiles for trip distances longer than 700–800 km. This study will help inform policy makers and transportation system operators about how differently each intercity system perform across all activities, and provides a basis for future policies designed to encourage mode shifts by range of service. The estimation procedures used in this study can serve as a reference for future analyses of transportation scenarios.     

Dynamic traffic metering in urban street networks: Formulation and solution algorithm

Traffic metering offers great potential to reduce congestion and enhance network performance in oversaturated urban street networks. This paper presents an optimization program for dynamic traffic metering in urban street networks based on the Cell Transmission Model (CTM). We have formulated the problem as a Mixed-Integer Linear Program (MILP) capable of metering traffic at network gates with given signal timing parameters at signalized intersections. Due to the complexities of the MILP model, we have developed a novel and efficient solution approach that solves the problem by converting the MILP to a linear program and several CTM simulation runs. The solution algorithm is applied to two case studies under different conditions. The proposed solution technique finds solutions that have a maximum gap of 1% of the true optimal solution and guarantee the maximum throughput by keeping some vehicles at network gates and only allowing enough vehicles to enter the network to prevent gridlocks. This is confirmed by comparing the case studies with and without traffic metering. The results in an adapted real-world case study network show that traffic metering can increase network throughput by 4.9–38.9% and enhance network performance.     

Including congestion effects in urban road traffic CO2 emissions modelling: Do Local Government Authorities have the right options?

Tailpipe emissions from vehicles on urban road networks have damaging impacts, with the problem exacerbated by the common occurrence of congestion. This article focuses on carbon dioxide because it is the largest constituent of road traffic greenhouse gas emissions. Local Government Authorities (LGAs) are typically responsible for facilitating mitigation of these emissions, and critical to this task is the ability to assess the impact of transport interventions on road traffic emissions for a whole network.This article presents a contemporary review of literature concerning road traffic data and its use by LGAs in emissions models (EMs). Emphasis on the practicalities of using data readily available to LGAs to estimate network level emissions and inform effective policy is a relatively new research area, and this article summarises achievements so far. Results of the literature review indicate that readily available data are aggregated at traffic level rather than disaggregated at individual vehicle level. Hence, a hypothesis is put forward that optimal EM complexity is one using traffic variables as inputs, allowing LGAs to capture the influence of congestion whilst avoiding the complexity of detailed EMs that estimate emissions at vehicle level.Existing methodologies for estimating network emissions based on traffic variables typically have limitations. Conclusions are that LGAs do not necessarily have the right options, and that more research in this domain is required, both to quantify accuracy and to further develop EMs that explicitly include congestion, whilst remaining within LGA resource constraints.     

Greenhouse gas emissions from road construction: An assessment of alternative staging approaches

The greenhouse gas (GHG) emissions associated with road construction activities are analyzed. The main focus of this analysis is on the vehicle emissions associated with alternative project staging approaches, specifically a full closure of the road during construction, versus an intermittent road closure. The analysis includes the direct and upstream emissions associated with materials, construction equipment, mobilization of resources to the work site, and maintenance activity associated with the project over its lifetime. The analysis is based on one case study of a road project in New Jersey. The assumptions underlying the staging analysis are based on hypothetical approaches. Results provide an assessment of the main sources of project related emissions and the ability to minimize total project emissions by minimizing traffic disruption. In the analysis with a full closure of the road, traffic disruption accounts for 26% of total emissions, while with an intermittent road closure, traffic disruption accounts for only 2% of total emissions. The other main sources are from materials and life-cycle maintenance. The analysis demonstrates the feasibility of minimizing project related GHG emissions during road construction activities.     

Strain prediction for critical positions of FPSO under different loading of stored oil using GAIFOA-BP neural network

FPSO (floating, production, storage and offloading) units are widely used in the offshore oil and gas industry. Generally, FPSOs have excellent oil storage capacity owing to their huge oil cargo holds. The volume and distribution of stored oil in the cargo holds influence the strain level of hull girder, especially at critical positions of FPSO. However, strain prediction using structural analysis tools is computationally expensive and time consuming. In this study, a prediction tool based on back-propagation (BP) neural network called GAIFOA-BP is proposed to predict the strain values of concerned positions of an FPSO model under different oil storage conditions. The GAIFOA-BP combines BP model and GAIFOA which is a combination of genetic algorithm (GA) and an improved fruit fly optimization algorithm (IFOA). Results from three benchmark tests show that the GAIFOA-BP model has a remarkable performance. Subsequently, a total of 81 sets of training data and 25 sets of testing data are obtained from experiment using fiber Bragg grating (FBG) sensors installed on the surface of an FPSO model. The numerical results show that the GAIFOA-BP is capable of predicting the strain values with higher accuracy as compared with other BP models. Finally, the reserved GAIFOA-BP model is utilized to predict the strain values under the inputs of a 10-day time series of volume and distribution of stored oil. The predicted strain results are further used to calculate the fatigue consumption of measurement points.