5000 PCC“SHANGHAI HIGHWY”船主机启动分析与处理

分析5 000 PCC"SHANGHAI HIGHWAY"船主机伺服油压低引起主机启动故障的原因、介绍调查与处理过程,在实施了恰当的处理方法后,解决了问题。以期为类似问题的处理与解决提供借鉴和参考。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

抗滑桩在滑坡处理中的应用

结合某国道滑坡情况,根据其具体的工程地质和水文情况,提出了采用抗滑桩的处理方案。根据滑坡推力计算,确定抗滑桩的尺寸及位置,提出了施工过程动态监测和完工后长期监测的方案。     

铁路路基动态变形模量的数值模拟分析

介绍铁路路基动态变形模量理论计算公式的推导及动态变形模量的测试原理,采用有限元软件模拟动态变形模量的测试过程,分析承载板与土体接触压力、路基动态变形模量的影响因素,并计算动态变形模量的有效测试深度.结果表明:在承载板中心一定范围内,接触压力模拟结果较理论计算值大;土体的动弹性模量对接触压力影响很小,可以忽略;路基动态变形模量测试冲击荷载作用下,土体只发生弹性变形;动态变形模量与土体动弹性模量呈线性关系,路基动态变形模量的模拟结果大于理论计算值;土体的泊松比对动态变形模量影响较小;动态变形模量有效测试深度建议取0.5~0.6 m.     

硬岩顶管卡滞原因分析及脱困技术研究

针对长距离岩石地层顶管施工中预制管卡滞工程难题,结合观景口水利工程2#无压洞工程,通过资料查阅、案例调研、专家咨询等方法,对多种处理方案进行对比分析。结合工程实践,提出预制管受困点判别方法,并研究制定出沉渣冲洗清理及预制管拆除方案;结合顶管施工特点就如何预防预制管卡滞提出针对性改进措施。经工程验证,所采取方案与技术措施顺利解决了预制管卡滞难题,并确保了后期工程的顺利进行,既缩短了工期又取得了良好的经济效益.,可为类似工程提供借鉴和参考。     

Buckle propagation of damaged SHCC sandwich pipes: Experimental tests and numerical simulation

Sandwich pipe (SP) combining high-strength performance and thermal insulation has been considered an effective solution for oil and gas transportation in ultra-deepwater. Strain hardening cementitious composite (SHCC) is well known for its capacity to withstand both tensile load and external hydrostatic pressure. The sandwich pipe considered in the research is constituted of concentric steel pipes with SHCC annular layer. In the present research work, the SHCC was manufactured, and full scale sandwich pipes were assembled. Intact and damaged specimens were submitted to controlled external pressure in a hyperbaric chamber to obtain the collapse and propagation pressures, respectively. Modeling and simulation of the buckle propagation of the SPs were correlated with the experimental results. The results show that sandwich pipe with SHCC core has an excellent structural strength under high external pressure in both intact and damaged conditions. Moreover, the results also show that the interaction between the annular and the inner/outer pipes provides a significant contribution to the buckling resistance under propagation pressure.     

Modeling free-flow speed according to different water depths—From the viewpoint of dynamic hydraulic pressure

In this paper, we propose a method of modeling free flow speed from the viewpoint of hydroplaning. First, the lift forces for different water depths were estimated using Bernoulli’s equation. Compared with the result of the experimental test performed by the Japan Automobile Research Institute, the hydrodynamic pressure coefficient was determined to be 0.03 (tf s²/m⁴). The validation of the predicted lift force is found in another published paper. A very good match is found between the computed values by the proposed numerical model and the data in other published papers. Then, the loss of contact force is considered to evaluate the hydroplaning performance of a tire. To simulate the hydroplaning speed, a tire-sliding model was utilized to obtain the traction and friction forces between the road surface and the tire. The observation data obtained in Japan in 2009 is compared with the physically computed hydroplaning speed, yielding the conclusion that the traction force at the measured desired speed is, on average, 23.4% of the traction force at hydroplaning speed. The analytical model offers a useful tool to quantitatively show that the free flow speed changes as the water depth increase.     

液压式盾构/TBM主机平移-空推集成装置的研制

研究目的:目前,隧道掘进机平移与空推工艺多采用不同装置分步完成,装置安装耗时费力,严重影响项目施工进程,且国内外没有可同时解决掘进机主机平移和空推的工法或装置。本文研制了一种基于液压的盾构/TBM主机平移-空推集成装置,将平移与空推工序合一,可极大提高工程施工效率,实现荷载600 t盾构/TBM主机连续移位。研究结论:(1)利用液压力驱动液压马达实现装置移位和驱动轮90°转向,实现了平移与空推工艺集成;(2)多轮系和从动轮碟簧设计可优化载荷分布,从动轮选用自润滑推力关节轴承使装置可适应一定倾斜度和不平度,提升装置运行平稳性;(3) 600 t荷载下,利用聚氨酯包敷于钢轮外的复合轮设计减小了轮系与地面接触应力,降低地面要求;(4) ANSYS仿真分析表明承载台架满足强度要求;(5)目前该装置已成功应用于青岛地铁8号线项目,缩短工期20 d,填补了国内外技术空白,应用前景广阔。     

南昌地铁砾砂层渣土改良技术试验研究

随着土压平衡盾构的广泛推广和应用,其地层适应性也越来越强,但盾构机在一些特殊地层中掘进时,渣土无法满足盾构施工对渣土流塑性的要求,易造成刀盘结饼、掌子面压力不稳定、刀盘磨损严重等问题。泡沫渣土改良技术是保证施工安全、顺利进行的关键技术之一。本文针对两种工程现场常用的泡沫进行泡沫基础性能试验,并以南昌地铁3号线盾构区间为工程背景,针对该区间砾砂地层进行改良渣土坍落度试验,对不同注入率和不同发泡剂的改良效果进行分析。研究发现,两种泡沫剂的建议使用浓度为3%;渣土流动性随泡沫注入率的增大而提高。在试验所用土样条件下,建议施工时使用的泡沫注入率为20%~30%。     

深海超高压环境模拟容器裂纹评定

深海超高压环境模拟容器用于模拟水下压力环境,其容器壁上承受反复载荷,容易产生疲劳裂纹.疲劳裂纹扩展是影响其断裂的主要因素.本文旨在分析半椭圆裂纹在老化的深海超高压环境模拟容器中的扩展行为,评估容器的安全性,因此对材料20MnMoNb钢的裂纹扩展特性进行了试验研究,首先考虑三角形和梯形加载情况,通过比较两组实验结果,考察了其材料对保载时间的敏感性.采用基于统一的裂纹扩展率模型的三维有限元方法进行了疲劳裂纹扩展计算,并通过CT试样的一组数值和实验结果进行了验证,最后建立了不同初始尺寸、展弦比和倾角的裂纹有限元模型,并根据裂纹在容器内壁的容许深度准则,计算了容器的剩余寿命.其分析结果可为深海超高压环境模拟容器可靠性评估提供参考.