块石基床爆夯技术在重力式码头的应用及质量控制

爆夯技术近年在重力式码头抛石基床上得到广泛应用,本文结合福建某重力式码头基床、地基及水文的实际情况,总结块石基床水下爆炸夯实技术的设计、施工工艺、质量控制及爆破的安全控制,以供类似工程参考。     

挖泥船产量计密度测量精度分析及放射源核素、活度选择研究

通过理论分析结合长江武汉航道工程局挖泥船施工现场情况提出以清水计数率作为密度测量精度的评价指标,在此基础上推导出针对不同排泥管径所需放射源活度的计算公式,据此结合现场条件建立放射源核素及活度的选择条件,为提高设备的有效性提供依据。     

烟台某工程循环水取、排水工程压水试验

为确定烟台某工程地基基岩的渗透特性,阐述水上岩体压水试验的主要操作过程、试验数据处理和试验结果分析评价方法．测定区域内的各岩层的透水率和渗透系数,给出不同风化程度岩层的渗透性评价,为设计提供防渗设计所需参数。     

基于区内出行比例的城市交通小区半径计算方法

针对国内城市交通小区划分多靠定性分析的情况,分析了国内外交通小区划分方法,提出了基于区内出行比例的交通小区半径定量计算方法。基于交通小区半径和出行距离的三种不同组合,推导出了相应的区内出行比例计算模型,利用Excel软件的VBA编程功能,进行了三者之间的数量关系计算,通过对区内出行比例的控制,得出交通小区半径的合理范围。实例计算结果表明:当区内出行比例范围为5%～10%时,西安中心市区交通小区的合理半径在0.7～1.1km之间,而实际调查区内出行比例为9.28%,交通小区半径为0.9km,调查值与计算值接近,小区半径定量计算方法可行。     

铁道车辆运行安全评判的轮对爬轨脱轨准则

为了掌握车辆爬轨脱轨机理及主要影响因素,分析了轮对的三维空间受力,推导了轮轨横向力和垂向力比值的一般表示式,假设车轮在达到最大轮缘接触角时为脱轨的临界状态,并认为这时轮轨间出现完全摩擦滑动,导出了不考虑轮对摇头角的临界脱轨判别的二维准则与考虑轮对摇头角和轮轨蠕滑率效应的三维脱轨判别准则,给出了轮轴脱轨系数的定义,采用轮轴脱轨系数和轮重减载率进行脱轨的判别。仿真计算结果表明:二维脱轨判别准则与三维准则相比偏于保守;摇头角越小甚至变负,越有利于防止脱轨,摇头角越大,三维准则的临界脱轨曲线越接近于二维准则的;减小轮轨摩擦系数与增大轮缘角均有利于防止脱轨的发生。     

Corrosion rate measurements in steel sheet pile walls in a marine environment

Corrosion of steel structures in the marine environment is a major problem. The deterioration of this kind of structures is costly and difficult to predict both when designing new structures and when estimating the remaining service life time for existing structures. The aim of this investigation was to find indicative values for the corrosion rate of steel sheet piles on the Swedish west coast. Such corrosion rates (mm/year) can be used both when designing new structures by oversizing the steel thickness and when estimating the bearing capacity of existing sheet pile structures. Earlier investigations on the corrosion rates along the Swedish east coast – with salinity from about 0.2% to 0.8% – are still used today as guidelines for the corrosion rate of all steel structures in the Swedish maritime environment even though the salinity on the west coast can be as high as 3.0%.Steel sheet pile wharfs located in the port of Halmstad on the Swedish west coast were inspected by ultrasonic measurements. Three wharf structures with a total length of about 700 m were inspected. None of the inspected wharfs had or have had cathodic protection. The thickness measurements of the steel sheet pile structures were performed by divers.The age of the three inspected sheet pile structures ranged from 36 to 51 years. The dimensions of the original sheet pile sections are known. One of the quay structures is located along a river. The salinity at all wharfs varied from low values at the surface to approx. 2% at the bottom (also in the river outflow).The measured average corrosion rates were in the same order as the design values in the European code. However, the results indicate increased corrosion rates about 1 m below the mean water surface and at the level of the propellers from the ships berthing the most frequented of the inspected wharfs, 3–6 m below water surface.The tolerances of steel sheet thicknesses – usually in the order of ±6% – are often neglected when investigating the remaining thickness in steel sheet piles. A simple calculation model shows that the sheet pile must be almost 50 years of age before an accurate estimation on the corrosion rate can be made, considering the tolerances, if the true original sheet pile thickness is not known.     

沥青路面运营初期平整度竣工验收标准研究

采用数理统计原理,运用SPSS软件对陕西省7条高速公路交-竣工平整度数据进行分析,得出了陕南、关中和陕北地区路面平整度衰变幅度均值分别为0.39m/km、0.28m/km和0.24m/km,这也将作为计算竣工验收推荐值的依据;再基于交-竣工平整度变化规律,建立了平整度竣工验收推荐值的计算公式:IRIju=IRIji+IRIs,可为今后平整度竣工验收标准提供有效的理论依据。     

数控铣床加工低碳钢零件的进给速度优化

论述了数控铣床加工低碳钢零件时进给速度的优化问题．在基于加工效率（可等效转化为加工工时）和加工成本目标函数的基础上，对这两个目标函数运用多目标函数理论进行综合，得到了多目标综合函数．通过计算，并综合表面粗糙度，进而得到进给速度的优化范围，并对不同转速下的进给速度给出了相应的优化参数，目的更接近生产实际，使技术人员不仅了解影响生产效率和成本的因素，也可在实际生产的应用中更加快捷和方便．     

小样本条件下混凝土强度代表值的确定

针对小样本混凝土强度代表值确定时不能利用数理统计模型的问题,引入了信息扩散原理,提出了小样本条件下混凝土强度代表值确定的实用计算模型。2个混凝土强度检测案例的计算结果表明,利用《公路工程质量检验评定标准》(JTJ071-98)进行灌注桩芯样混凝土强度代表值确定,得到的代表值保证率在95%左右波动,具有不确定性;利用《超声回弹综合法检测混凝土强度技术规程》(CECS 02:88)进行单一构件混凝土强度推定,推定值的保证率小于95%,对结构的可靠性鉴定而言是偏于不安全的,应引起试验检测人员的充分重视。