Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

动力集中和动力分散的特点

从运用、市场和列车型式的发展趋势等方面 ,分析了动力集中和动力分散的特点。特别阐述了利用寿命周期成本 (L CC) ,来比较这 2种方式列车的优劣     

轻轨车辆的制造

根据庞巴迪运输部德国车辆制造有限公司（ＤＷＡ）轻轨车设计开发、车体模型制作与试验等课题研究情况，进一步介绍如何实现车体轻量化结构、防撞击设计、防火安全及采用的先进的焊接技术。     

Physical processes in wheel–rail contact and its implications on vehicle–track interaction

Friction within the wheel–rail contact highly influences all aspects of vehicle–track interaction. Models describing this frictional behaviour are of high relevance, for example, for reliable predictions on drive train dynamics. It has been shown by experiments, that the friction at a certain position on rail is not describable by only one number for the coefficient of friction. Beside the contact conditions (existence of liquids, solid third bodies, etc.) the vehicle speed, normal loading and contact geometry are further influencing factors. State-of-the-art models are not able to account for this sufficiently. Thus, an Extended-Creep-Force-Model was developed taking into account effects from third body layers. This model is able to describe all considered effects. In this way, a significant improvement of the prediction quality with respect to all aspects of vehicle–track interaction is expected.     

On the morphological long-term development of dumped material in a low-energetic environment close to the German Baltic coast

The development of the bed bathymetry of an experimental dumping area was followed over three-and-a-half years by means of multibeam echosounder techniques. Two types of material were discharged in the bight of Mecklenburg in the Baltic Sea in approximately 20 m of water depth. One set of the discharges was 2900 m³ of glacial till and the other set was a 2400 m³ mixture of glacial till, sand and minor amounts of cohesive matter. Only approximately 2500 m³ (86%) of the glacial till and 1500 m³ (63%) of the mixed soil materials were deposited on the seabed. This means that already during the dumping process a considerable part of the sediment material drifted away. The glacial till formed crater-like rings of 30 m diameter with peaks up to 1.4 m above seabed, whereas the spatial structure of the mixed soil material was somewhat more diffuse, but with similar magnitudes in the peaks and troughs.The morphological changes were small and their quantification required a high measuring precision in the order of few cm in the vertical. The dominant processes of surface deformation was flattening of peaks and filling of troughs. The speed of this process decreased with horizontal scale: structures of less than 4 m horizontal extension had a trend to disappear within less than five years, whereas structures of larger than 8 m extension showed little change and are estimated to remain detectable for many decades. In contrast to the reworking of the matter inside the dumping structures, no net transport of material out of the dumping area could be detected. Extrapolating the observed morphological changes into the future it is estimated that without significant decrease in internal shear strength of the disposed till the structures will persist for at least 70 years. This can be attributed to the high internal stability of the dumped glacial till and the low hydrodynamic forces present at the seabed in this region.     

Improvement of the volume-delay function by incorporating the impact of trucks on traffic flow

In current transportation modelling, travel time is the most important factor in decisions regarding transport modes, destinations and routes. The calculation of travel time is deployed by volume-delay functions (VDFs), a sub-model of route assignment procedure, using the correlation between increasing numbers of vehicles on a road and the road's restrictive capacity. By investigating existing VDFs, a clear gap is seen, demonstrating that current functions are not suited to reflect the empirically known large impact of trucks on passenger car travel times. This issue becomes crucial when transport models are used to reflect future scenarios where goods transportation is expected to increase greatly, and when transport models combine passenger and commercial traffic. This paper presents a new VDF which successfully includes trucks’ impact on traffic flow in the case of Germany and, with slight deviations, for North America. The function is developed using ideal-type data for German motorways. The differences between German and US data and their implications for VDFs are also discussed.     

Mortality through ontogeny of soft-bottom marine invertebrates with planktonic larvae

The present survey covers one spawning season of marine benthic invertebrates in a large geographical area, the inner Danish waters, and includes a wide range of habitats with steep salinity and nutrient load gradients. The loss ratios of soft-bottom marine invertebrates from one development stage to the next is calculated based on average abundances of pelagic larvae, benthic post-larvae and adults of Bivalvia, Gastropoda, Polychaeta and Echinodermata, with planktonic development. This gives a rough estimate of the larval and post-larval mortality. Loss ratios between post-larvae stage and adult stage (post-larval mortality) varies from 3:1 to 7:1 (71.2–84.9%) and loss ratios between larvae and post-larvae (larval mortality) and between larvae and adult, ranging from 7:1 to 42:1 (85.2–97.6%) and from 45:1 to 210:1 (97.8–99.5%), respectively. The results show a remarkable unity in loss ratios (mortality) between the mollusc taxa (Bivalvia and Gastropoda) at the phylum/class level. This similarity in loss ratios among the mollusc taxa exhibiting the same developmental pathways suggests that the mortality is governed by the same biotic and abiotic factors. Larval mortality is estimated to range from 0.10 d^− 1 to 0.32 d^− 1 for Bivalvia and ranging from 0.09 d^− 1 to 0.23 d^− 1 for Polychaeta. The species loss ratios combined with specific knowledge of the reproduction cycles give estimated loss ratios (mortality) between the post-larvae and the adult stage of 25:1 and 14:1 for the bivalves Abra spp. and Mysella bidentata. For the polychaete Pygospio elegans the loss ratio (larval mortality) between the larvae and the post-larval stage is 154:1 and between the post-larvae and the adult stage 41:1. For Pholoe inornata the loss ratio between post-larvae and adults is 7:1. The present results confirm that the larval stage, metamorphosis and settlement are the critical phase in terms of mortality in the life cycle for Bivalvia. Assuming steady state based on actual measurements of pelagic larval densities an estimated input to the water column of pelagic bivalve larvae is ranging from 10,930 to 17,157 larvae m^− 2 d^− 1 and for Polychaeta between 2544 and 3994 larvae m^− 2 d^− 1. These estimates seem to correspond to the reproductive capacity of the observed adult densities using life-table values from the literature.The potential settlement of post-larvae is 43 post-larvae m^− 2 d^− 1 for Bivalvia and 56 post-larvae m^− 2 d^− 1 for Polychaeta. The adult turnover time for Bivalvia is estimated to be 1.5 years and 2.1 years for Polychaeta. This exemplifies that species with short generation times may dominate in very dynamic transitional zones with a high frequency of catastrophic events like the frequent incidents of hypoxia in the inner Danish waters.     

Cooperative Estimation Using Vehicle Communications

Summary Each vehicle on a section of highway is potentially a driving condition 'sensor.' For example, a vehicle's speed give can give a clue about the traffic conditions in its section of roadway. By 'cooperative estimation,' we mean a system that uses a communication network to combine the experience of many vehicles into parameter estimates that are more useful than the estimates that any individual vehicle could generate by itself. This paper demonstrates the cooperative estimation concept by showing how it can be used to estimate traffic conditions and road friction without using roadside sensors.