Hydroelasto-plasticity approach to predicting the post-ultimate strength behavior of a ship’s hull girder in waves

Dynamic collapse behavior of a ship’s hull girder in waves is investigated; post-ultimate strength behavior is the focus. Firstly, a simulation method is proposed. Assuming that a plastic hinge is formed during the collapse of the hull girder, the whole ship is modeled as two rigid bodies connected amidship via a nonlinear rotational spring. The post-ultimate strength behavior, such as the reduction of load carrying capacity due to buckling and yielding, is reflected in the model. Hydrodynamic loads are evaluated by using nonlinear strip theory to account for the effect of large plastic deformations on the loads. A scaled model for validation of the simulation is designed and fabricated. Then a series of tank tests is conducted using the scaled model to validate the simulation results. Post-ultimate strength behavior characteristics in waves are clarified by using the numerical and tank test results. It is shown that the hull girder collapses rapidly after reaching ultimate strength, and then the plastic deformation grows until unloading starts at the collapsed section. Finally, several parametric dependencies of the extent of the collapse behavior are discussed based on a series of the simulations.     

Advanced Control Methods of Active Suspension

This paper describes new control methods for the active suspension. For improving ride comfort further, preview control rule is proposed. For improving stability further, roll stiffness distribution control rule is examined by the test vehicle. Simulations and vehicle driving tests are conducted to confirm the effect of these new control methods. The results of simulations and vehicle driving tests show in our research phase that preview control can achieve a substantial improvement in ride comfort and application of roll stiffness distribution control provides a large improvement in stability     

Development of an Active Control Engine Mount System

In an attempt to reduce idling vibration and booming noise in automobile engines, the authors have developed an engine mounting system we call the ACM(Active Control engine Mount) system. Comprising a pair of electromagnetic actuators and hydraulic mounts, the system incorporates an adaptive control strategy based on the synchronized filtered-X LMS (SFX) algorithm. The crank angle pulse signal is detected as the synchronization signal and the force transmitted to the car body through the engine mounts is detected as a residual signal. Application of the ACM system to a vehicle with a transversally mounted four-cylinder engine resulted in significantly reduced idling vibration and booming noise.     

前列腺特异性抗原值增高患者前列腺液中白细胞状态的研究

目的研究获取的前列腺特异性抗原(PSA)值增高患者的前列腺液中的白细胞状态。方法112例PSA值增高的患者在行经直肠前列腺穿刺活检前获取前列腺液,并行前列腺液中的白细胞计数。用相关分析和t检验分析白细胞与患者年龄、PSA、前列腺体积等的关系。结果所有患者的前列腺液中白细胞密度加大(平均5.29×106/mL),白细胞总数增高(平均1.58×106)。前列腺液的体积和白细胞总数与前列腺体积呈显著性相关,非前列腺癌患者较前列腺癌患者的前列腺体积和白细胞总数显著增高。结论非前列腺癌患者的PSA值增高可能与前列腺液中的白细胞增高有关。     

On the mechanism of the bursting phenomena of propeller tip vortex cavitation

 The bursting phenomenon of tip vortex cavitation of a propeller sometimes causes severe high-frequency vibration, but its mechanism has not yet been elucidated. In this study, we carried out model experiments by changing the propellers, wake distributions, thrust coefficients, and cavitation numbers parametrically, examined the bursting phenomenon with a high-speed video camera, and measured the pressure fluctuations caused by the phenomenon. We also measured flow distribution around the tip vortex. As a result, we found that in the bursting phenomenon, large pressure fluctuations occurred twice, and that they strongly depended on the wake distribution. Two means were suggested to suppress the bursting phenomenon, other than changing the wake distribution: stabilizing tip vortex cavitation or reducing the cavity volume. Numerical fluid simulations around a propeller in noncavitating, unsteady conditions were also conducted, and the strength of the tip vortex along the circumference and its derivative were examined. As a result, the phenomena were parameterized by the time derivative of the strength of the tip vortex, and if it was higher than a threshold value, the tip vortex cavitation burst. Therefore, it is possible to predict the occurrence of the bursting phenomenon by numerical analysis. Received: November 6, 2001 / Accepted: January 24, 2002     

Study on the design of propeller blade sections using the optimization algorithm

A new method for designing propeller blade sections is presented. A vortex lattice method is used to evaluate the performance and the time-dependent pressure distribution on the blade surface in a non-uniform flow, while efficient optimization algorithms are used to modify the blade sections. Two different designs were carried out in this study. The first was a design to realize a target pressure distribution in a rotating three-dimensional flow. A two-dimensional wing theory was used to obtain the target pressure distribution. The predicted increase in efficiency and the reduction in the cavity volume were confirmed by model experiments. The second was a design to maximize the propeller efficiency. By this method, the propeller efficiency was improved by 1.2% under the constrains of constant thrust and a prescribed margin for face cavitation.     

Effect of wheel-slip prevention based on sliding mode control theory for railway vehicles

It is important to consider the robustness when designing brake control systems, because of the model's uncertainties that result from the nonlinear characteristics of wheel-to-rail adhesion forces and brake material friction coefficients. This paper presents the experimental results from the new wheel-slip prevention control using nonlinear robust control theory. The authors performed experiments for the proposed wheel-slip prevention control to compare it with the conventional control laws. The experimental results proved the comparative effectiveness of the proposed control and showed high brake performance under nonlinear characteristics of brake dynamics.