Gain and noise figure analysis of Er<Superscript>3+</Superscript>-doped YAG transparent ceramic microchip amplifier

The rate equations and the power evolution equations based on excited state absorption (ESA) and cooperative upconversion (CUC) of high concentration erbium-doped yttrium aluminum garnet (YAG) transparent ceramic waveguide amplifier are set up to analyze the effects of the pump power, active ion concentration and waveguide length on the amplifier gain and noise figure (NF). The numerical analysis predicts that with a pump power of 100mW, an active ion concentration of 1.0×10²⁶ ion/m³ and a waveguide length of 3 cm, a small-signal gain of 30 dB and an NF of 5 dB can be achieved in the micro-chip amplifier.     

Study of the helicopter blade running elevation measurement system

Helicopter blade running elevation measurement is an important measure target in helicopter blade dynamic balance experimentation. The elevation influences the helicopter＇ s security and other performance capabilities. In testing, however, it has been difficult to measure the elevation when the rotor reaches high speeds. To get a simple, fast and highly accurate measurement system, photo electricity technology was applied to measuring the blade running elevation. Discussed is the measurement principle of blade running elevation, tire design of the measurement system and analysis of the measurement precision.     

Course-keeping control of underactuated hovercraft

The course-keeping control of underactuated hovercraft with two aft propellers was considered. The control of the heading error and cross-track error was accomplished by the yaw torque merely in this case. The hovercraft dynamic model is nonlinear and underactuated. At first the Controllability of course-keeping control for hovercraft was proved, then a course-keeping control law was derived that keeps hovercraft heading constant as well as minimizes the lateral movement of hovercraft. The proposed law guarantees heading error and sway error all converge to zero exponentially. Simulation tests were carried out to illustrate the effectiveness of the proposed control law. For further research, the disturbance influence would be considered in the dynamic equations.     

Special requirements for alumina ceramic of ESG electrode bowl

At present ESG (Electrostatic Suspended Gyro) is the most precise inertia element in the world. The electrode bowl, which has direct effect on the precision of ESG, is a key part to ESG. Through the analysis of the function and characteristic of the electrode bowl in hollow rotor ESG and the present situation of new material development in the world, the alumina ceramic is regarded as the best material for the electrode bowl of hollow rotor ESG. By analyzing the present situation of alumina ceramic in the world, main technique requirements have been put forward for the alumina ceramic of ESG electrode bowl which is also fit for solid rotor ESG.     

Gasket life criteria at low temperatures adopting proportional compensation for loss of flexibility and conformability

In the automobile industry, the service life of gaskets is defined as the time until which a released gasket recovers 60 % of the original compression. It was observed that the recovery curves of gaskets were highly nonlinear at high temperatures, and relatively nonlinear at temperatures above the room temperature. However, it was also noted that the recovery curves of the gaskets at temperatures below room temperature exhibited linearity with respect to the ln(time). Automotive manufacturers demand gasket life criteria that exceed a specific time or the entire life of a car. In the case of gaskets used at lower temperatures, since materials encounter losses in its flexibility and conformability, the definition of service life specifying a 60 % recovery may not be sufficiently safe to eliminate possible leakages. In this study, new gasket life criteria that could be used at low temperatures were proposed. The new criteria were proposed based on the change in Young’s modulus of the gasket material in order to conserve the sealing capability.     

Performance Design of an Exhaust Superheater for Waste Heat Recovery of Construction Equipment

Although fuel cost has been the largest portion of annual operating costs of construction equipment, it is possible to save the energy and reduce cost using fuel economy enhancement technology. In this study, an organic Rankine cycle is applied to an excavator in order to recover waste heat, reproduce it into electrical energy, and consequently reduce the fuel consumption by 10 %. A design process was carried out to develop an exhaust gas superheater that recovers the waste heat from exhaust gas through a composite-dimensional thermal flow analysis. A one-dimensional code was developed to perform a size design for the exhaust gas superheater. The ranges for the major design parameters were determined to satisfy the target of the heat recovery, as well as the pressure drop at both fluid sides. Performance analysis was done through onedimensional design code results, which were compared with three-dimensional CFD analysis. By utilizing a 3D commercial code, the arrangement of the tubes was selected and the working fluid pressure drop was reduced through a detailed layout design. The design procedure was verified by a performance evaluation of the prototype, which yielded only a 7 % tolerance in heat recovery.     

Effects of Residual Ash on Dpf Capture and Regeneration

To study the effects of residual ash on the capture and regeneration of a diesel particulate filter (DPF), repeated capture and complete regeneration experiments were conducted. An engine exhaust particulate sizer was used to measure the particle size distribution of diesel in the front and back of DPF. Discrepancies in the size distribution of the particulate matter in repeated trapping tests were analyzed. To achieve complete DPF regeneration, a DPF regeneration system using nonthermal plasma technology was established. The regeneration carbon removal mass and peak temperatures of DPF internal measuring points were monitored to evaluate the effect of regeneration. The mechanism explaining the influence of residual ash on DPF capture and regeneration was thoroughly investigated. Results indicate that the DPF trapping efficiencies of the nuclear-mode particles and ultrafine particles have significant improvements with the increase quantity of residual ash, from 90 % and 96.01 % to 94.17 % and 97.27 %, respectively. The exhaust backpressure of the DPF rises from 9.41 kPa to 11.24 kPa. Heat transfer in the DPF is improved with ash, and the peak temperatures of the measuring points accordingly increase. By comparing the regeneration trials, the elapsed time for complete regeneration and time difference for reaching the peak temperature between adjacent reaction interfaces are extended with increased quantity of ash. The carbon removal mass rises by 34.00 %.     

Feature-Based Cad System Buildup for Passenger Airbag Design

The passenger airbag (PAB) requires a large volume and fast deployment because of the large distance between the dashboard and the passenger. And various shapes and sizes of the PAB are required depending on the type of vehicle. However, since the PAB modeling process for each design change is complicated and time consuming, the design parameters of the PAB could not be well investigated. In this study, a unique feature-based CAD system has been proposed that easily constructs PAB CAD model and then generates PAB FE model for collision analysis. Main keypoints and widths of PAB that determine the shape and size have been extracted by analyzing the geometric-feature of airbag. The PAB CAD model can be easily constructed by inputting keypoints and widths information. Then, from the constructed PAB CAD model, the PAB FE model is automatically generated. Finally, the generated PAB FE model can be directly employed for collision analysis, thereby reducing the modeling time of the PAB and enabling efficient parametric studies on design.