Experimental ivnestigation on flow fields of viscous fluid around two-dimensional wings and comparison with computational results

To examine the flow field of a viscous fluid around the trailing edge of a wing with respect to the Kutta condition or the Joukowski hypothesis, an experimental investigation into the velocity fields around two-dimensional (2D) wings NACA0012 and NACA4412 was carried out using an X-type hot-wire anemometer in a wind tunnel and the method of colored milk injection in a circulating water channel. The results of these investigations revealed that the flow of a viscous fluid at the trailing edge of a 2D wing is tangential to the face on the pressure side, and that the flow is very slow or reversed on the suction side due to separation when the angle of attack is greater than 7.5°. By flow visualization, a Kármán vortex street was found in the wake of both wings (NACA0012 and NACA4412) when the angle of attack was 5°. These results show that the ordinary Kutta condition with respect to the direction of outflow at the trailing edge is not necessarily satisfied in a viscous fluid, but the Kutta condition with respect to the pressure at the trailing edge is satisfied as usual. Numerical results, which have been obtained as the solution of Reynolds-averaged Navier-Stokes equations, show good agreement with above-mentioned experimental results. Therefore, CFD (Computational Fluid Dynamics) simulation has proved to be very effective for studying steady viscous flow around the trailing edge of a 2D wing.     

A novel physiological index for Driver’s Activation State derived from simulated monotonous driving studies

Automobile driving in monotonous situations such as driving for long periods and/or travelling a familiar route may cause the lowering of the driver’s awareness level or what we term here as a Driver’s Activation State (DAS), resulting in an increased risk of an accident. We propose here to develop means with which to create an in-car environment so as to allow active driving, hopefully thus avoiding potentially dangerous situations. In order ultimately to develop a validated activation method, we firstly set out to examine physiological variables, including cardiovascular parameters, during simulated monotonous driving. Subsequently, we investigated the derivation of a suitable DAS index. During the experiment, a momentary electrical test stimulus of 0.5 s duration was applied at a rate of approximately once per 10 min to the subject’s shoulder to evoke a physiological responses. In 11 healthy male volunteers we successfully monitored physiological variables during the experiment and found particular patterns in the beat-by-beat changes of blood pressure in response to the electrical test stimulus. This finding, explained by autonomic activity balance, suggests that the patterns may be used as an appropriate and practicable index relevant to the Driver’s Activation State.     

Short sleep duration,sleep disorders,and traffic accidents

Sleepiness is an important factor in traffic accidents caused by human error. The purpose of this paper is to review a number of studies conducted over the years regarding the effect of the lack of sleep on the incidence of traffic accidents as well as the individual effects of various sleep disorders on accidents. In addition, we discuss recent advances in methods of detecting sleepiness and strategies for preventing traffic accident by using these methods.     

Transformation Plasticity─The Effect on Metallo-Thermo-Mechanical Simulation of Carburized Quenching Process

IntroductionInelashcorhaersiblestrainaccompaniedbyslidingofcrystalsduetothermalandphasetransformationdilatationiswellknowntointensivelythethedistonionofworkpieceunderqUopching,andsomanynumericalsimulatonsll-7]havebeencAnedoutintheframeworkofmotallochermo-mechwhcsl1].Transformationplasticity(TP),anothekindofbeversiblestrain,isalsorecognizedasoneofdominantparwtersthechngthestr6ssanddistorton,andsomenumcricalcalculationaremadebytakingtheeffectintoconsideration.Figurelschematicallyillustraresthe…     

Comparison of Feedforward and Feedback Control for 4WS

A system incorporating feedforward plus feedback control was configured such that it would follow the target yaw rate found by calculation. Selection of optimum values for the control system constants made it possible to separate control of the steering input response characteristic from control of vehicle stability against external disturbances. The former is controlled by the feedforward control function and the latter by the feedback control function; the values of the two functions can be set independently.     

Ecological modeling as a tool for coastal zone management in Dokai Bay, Japan

An ecological numerical model has been developed for coastal zone management in Dokai Bay, Japan. The numerical model experiment reproduces the occurrence of red tides and oxygen-deficiency in Dokai Bay during summer. Moreover, the model experiments forecast that when the phosphorus or nitrogen load from land will be cut by 90% or 95%, respectively, red tides and oxygen-deficiency will not occur in Dokai Bay. If the sewage facility is not sufficient to cut the nutrients load to the necessary degree, it is necessary to consider other countermeasures such as cultivating bivalves in order to decrease the nutrients in the bay.     

Multi-scale modeling of fatigue crack propagation applied to random sequence of clustered loading

Fatigue crack propagation in marine structures is obviously governed by mechanics of the considerably different four levels of multi-scale problems. Problems of structural response to environmental loads have length scale of several hundred meters, whereas possible detectable size of cracks from initial defects in a weld is of the order of millimeters. Once a fatigue crack initiates, crack tip plasticity is of the order of several grain sizes, while the resulting fatigue crack growth in each load cycle is of the order of nanometers. In our previous work, the first author and their associates have developed the so-called CP-System, which can treat the first two multi-level problems as an integrated system. Furthermore, we have incorporated the third level of mechanics by using the stress intensity range corresponding to the repeated tensile plastic deformation ahead of the crack tip. In the present paper, we shall discuss a more rational integral equation-based formulation in order to integrate the third and fourth levels of micro-mechanics to the first two levels of continuum mechanics.The method is then applied to fatigue crack propagation under the effects of random sequence of clustered loading. As an example of the random sequence of clustered load, we shall use the so-called “storm model”. In the crack propagation simulation, we have to take into account of the plastic wake on the crack surfaces, whose thicknesses are influenced by the material parameters involved in the crack growth model. These parameters are first identified by the fatigue tests under combined constant and random loading using a CT specimen. Then, fatigue crack growth is investigated by numerical simulation and fatigue tests for various random sequences of clustered loading. The experimental and numerical results agree quite well with each other, and fatigue crack propagation is found to be considerably retarded under random sequence loading, so that the conventional equivalent stress approach may provide rather conservative results to the real seaway loading.     

Analysis of hydrodynamic characteristics for arbitrary multihull ships advancing in waves

Multihull vessels have emerged as popular alternatives to conventional monohull ships for high-speed crafts. However, the bridging structures connecting the hulls are vulnerable to various wave actions and the wave impact on the bottom of them is the most serious problems associated with multihulled vessels. In this study, prediction of relative wave elevations under the bridging structures is investigated for multihull ships traveling with forward speed in waves. A computer code YNU-SEA using the three-dimensional (3D) Green function method with forward speed has been developed and used to analyze the hydrodynamic radiation and diffraction forces and motion responses for high-speed catamarans in waves. The results of the present calculations are compared with those of previous calculations as well as with experimental results. The numerical results reveal that the present computer code can be used as a powerful tool for the accurate numerical computation of seakeeping problems for multihull ships advancing in waves. Numerical calculations of wave pattern are also carried out including wave interactions between the hulls to analyze the effects of hull form on the free surface flow around catamarans advancing in waves. The analysis of the wave pattern allows the determination of relative wave height including radiation and diffraction waves. Finally, some discussions are included based on these numerical results which may be helpful for the accurate prediction of relative wave height and wave breaking load on the deck associated with multihull ships.