Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

用于预测含层间间隙缺陷柔性立管的静水压溃强度的弹性支撑拱结构模型

  目的  随着油气勘探涉入超深水领域,一旦柔性立管的外层结构发生破损,其内部的骨架层将承载巨大的外部水压。如果骨架层与铠甲层之间存在层间间隙,则将削弱骨架层的压溃强度,进而引发所谓的湿压溃。  方法  针对该问题,提出一种弹性支撑拱结构模型,并将骨架层的湿压溃过程分为接触前与接触后2个阶段。在接触之前,采用单环结构的稳定性理论分析内骨架层的失稳行为;当层间间隙闭合之后,骨架层开始受到铠甲层的支撑,该结构进入接触后阶段,此时外部铠甲层可以简化为径向支撑弹簧,用于支撑内部骨架层的分离拱状部分。基于此,建立有限元压溃模型,用以验证该解析模型的可靠性。  结果  2类模型的预测结果吻合良好,压溃压强对铠甲层刚度和间隙宽度均非常敏感;当初始层间间隙宽度由0增加至0.5 mm时,柔性立管的压溃压强将降低18%左右;如果紧密拟合的骨架由更硬的铠甲层支撑,则将大幅提高其抗压溃强度。  结论  对于具有较硬铠甲层和较小层间间隙的柔性立管而言,该解析模型可以有效预测其静水压溃强度。     

An approach to estimation of near-surface turbulence and CO2 transfer velocity from remote sensing data

The air–sea CO₂ exchange is primarily determined by the boundary-layer processes in the near-surface layer of the ocean since it is a water-side limited gas. As a consequence, the interfacial component of the CO₂ transfer velocity can be linked to parameters of turbulence in the near-surface layer of the ocean. The development of remote sensing techniques provides a possibility to quantify the dissipation of the turbulent kinetic energy in the near-surface layer of the ocean and the air–sea CO₂ transfer velocity on a global scale. In this work, the dissipation rate of the turbulent kinetic energy in the near-surface layer of the ocean and its patchiness has been linked to the air–sea CO₂ transfer velocity with a boundary-layer type model. Field observations of upper ocean turbulence, laboratory studies, and the direct CO₂ flux measurements are used to validate the model. The model is then forced with the TOPEX POSEIDON wind speed and significant wave height to demonstrate its applicability for estimating the distribution of the near-surface turbulence dissipation rate and gas transfer velocity for an extended (decadal) time period. A future version of this remote sensing algorithm will incorporate directional wind/wave data being available from QUIKSCAT, a now-cast wave model, and satellite heat fluxes. The inclusion of microwave imagery from the Special Sensor Microwave Imager (SSM/I) and the Synthetic Aperture Radar (SAR) will provide additional information on the fractional whitecap coverage and sea surface turbulence patchiness.     

The Dynamics of a Railway Freight Wagon Wheelset With Dry Friction Damping

Summary We investigate the dynamics of a simple model of a wheelset that supports one end of a railway freight wagon by springs with linear characteristics and dry friction dampers. The wagon runs on an ideal, straight and level track with constant speed. The lateral dynamics in dependence on the speed is examined. We have included stick-slip and hysteresis in our model of the dry friction and assume that Coulomb's law holds during the slip phase. It is found that the action of dry friction completely changes the bifurcation diagram, and that the longitudinal component of the dry friction damping forces destabilizes the wagon.     

Causes and effects of FDI by the Norwegian maritime industry

A theory of replacement in the context of ocean going vessels is discussed. The approach is based upon costs rather than profits, and while there appear to be many difficulties in applying replacement theory to ships it is shown that there are some segments where the theory can still usefully be applied. The effect on replacement resulting from varying important cost parameters is shown and it is found that while fiscal measures have very little effect, capital cost and operating cost profiles have the most important influence. It is concluded that shipowners need to keep themselves fully informed of changes in cost and improvements in technology that may indicate replacement of a vessel somewhat sooner than normal replacement age.     

In-Plane and Out-of-Plane Dynamics of Pneumatic Tyres

During the last decade research has been conducted on the dvnamics of the tvre considered as a vehiclecomponent. Asurvey is given of these developments where tyre mass plays an important role. The underlying theoretical considerations concerning the massless tyre have been discussed as well. Two groups of tyre response have been distinguished: the lateral (out-of-plane) response and the vertical/longitudinal (in-plane) response to motions of the wheel. In both categories tyre compliance, slip and inertia have influence. The dynamic properties of the rolling tyre have been presented in the form of transfer functions and/or differential equations. The frequency of the imposed oscillations is assumed to be below ca. 40 Hz. Non-linear effects and modelling have been briefly touched on.     

Norwegian North Sea action programme: Analysis of measures to reduce nutrient inputs

According to the terms of the Ministerial Declaration on the Protection of the North Sea, input of the nutrients phosphorus (P) and nitrogen (N) to the coast from the Norwegian‐Swedish border to Lindesnes should be reduced by about 50% between 1985 and 1995. The State Pollution Control Authority (SFT) has analyzed how Norway can achieve this reduction in the most cost‐effective way and at the same time achieve the greatest possible improvement in water quality along the Norwegian coast and in its watercourses.

Two alternative sets of measures were analyzed, both of which would meet the requirements of the Declaration. The lowest‐cost alternative would have average annual costs of about NKr 930 million (U.S.S150 million), and investments of about NKr 4000 million (U.S. $643 million). However, this set of measures would not take account of local water quality, and measures would therefore not always be introduced where the need is most pressing. SFT proposed that an alternative set of measures be implemented, almost all of which would also help to achieve local goals for water quality. This alternative will have annual costs of about NKr 980 million (U.S.$158 million), and investments of about NKr 4100 million (U.S.$659 million).     

Ballast Water Treatment systems: “Old” and “New” ones

This paper offers an overview of the currently available Ballast Water Treatment systems, their efficacy in reducing the number of organisms in relation with the IMO and other, future standards, and explores potentially new and promising technologies and current gaps.     

Full-scale fatigue tests of ship structures to validate the S–N approaches for fatigue strength assessment

Ships belong to those welded structures which are prone to fatigue due to high cyclic loads. Different approaches exist for the fatigue strength assessment which are varying between the industrial sectors. Therefore, deeper fatigue strength investigations were performed in Germany within an industry-wide joint research project aiming at the harmonization of the approaches. Regarding ship structures, two types were selected for full-scale tests. The first concerned web frame corners being typical for roll-on/roll-off ships (ro/ro) ships, from which three models were tested under constant amplitude loading. The second type was the intersection between longitudinals and transverse web frames, which recently showed fatigue failures in containerships. Five models were tested, three under constant and two under variable amplitude loading. All tests showed a relatively long crack propagation phase after first cracks had appeared, calling for a reasonable failure criterion. For the numerical analysis, the structural hot-spot stress as well as the effective notch stress approach have been applied. The latter allows the consideration of the weld shape which could partly explain differences in the observed and calculated failure behaviour. Another factor is the distribution of welding-induced residual stresses, which obviously affected the failure behaviour in the web frame corner as well. Insofar the investigations give a good insight into the strength behaviour of complex welded structures and into current problems and opportunities offered by numerical analyses.