Performance Evaluation of Hybrid-Drive Buses and Potential Fuel Savings in Brazilian Urban Transit

Transporting more than 55 million passengers per day, buses are the main transit mode in Brazil. Most of these vehicles use diesel oil and this situation causes dependence on oil, extensive greenhouse gas emissions and increasing air pollution in urban areas. In order to improve this situation the options for Brazilian cities include the use of alternative fuels and new propulsion technologies, such as hybrid vehicles. This article proposes a procedure for evaluating the performance of a recently developed Brazilian hybrid-drive technology. A simple procedure is presented to compare hybrid-drive buses with conventional diesel buses in urban operation focusing on fuel economy and the potential for reducing diesel oil consumption through the use of hybrid-drive buses. Field tests carried out by the authors indicate that fuel consumption improvement through the use of hybrid-drive buses would certainly exceed 20%, resulting in lower fuel costs and reduced carbon dioxide (CO₂) emissions.     

Influence of vehicle driving parameters on the noise caused by passenger cars in urban traffic

In this work, a sample of vehicles has been instrumented to measure of variables that influence vehicle noise emissions in Madrid. A circuit reproducing a normal travel pattern in large city is traveled by a fleet of vehicle models representing the fleets of cars in a European city. A sample of drivers covers the test track under different traffic conditions. Driving parameters and noise emitted have been recorded in each test and average values have been extracted. These data have been analyzed to define the noise emissions produced by a vehicle in real driving conditions and to identify the noisiest driving behaviors.     

Comparison on travel scheduling between driving and walking trips by habitual car users

Research on walking behavior has become increasingly more important in the field of transportation in the past decades. However, the study of the factors influencing the scheduling decisions related to walking trips and the exploration of the differences between travel modes has not been conducted yet. This paper presents a comparison of the scheduling and rescheduling decisions associated with car driving trips and walking trips by habitual car users using a data set collected in Valencia (Spain) in 2010. Bivariate probit models with sample selection are used to accommodate the influence of pre-planning on the decision to execute a travel as pre-planned or not. The explicative variables considered are: socio-economic characteristics of respondents, travel characteristics, and facets of the activity executed at origin and at destination including the scheduling decisions associated with them. The results demonstrate that a significant correlation exists between the choices of pre-planning and rescheduling for both types of trips. Whether for car driving or walking trips, the scheduling decisions associated with the activity at origin and at destination are the most important explicative factors of the trip scheduling and rescheduling decisions. However, the rescheduling of trips is mainly influenced by modifications in the activity at destination. Some interesting differences arise regarding the rescheduling decision processes between travel modes: if pre-planned, walking trips are less likely to be modified than car driving trips, showing a more rigid rescheduling behavior.     

Correlates of bicycling trip flows in Hamilton,Ontario: fastest,quietest, or balanced routes?

Transportation - Bicycling is an increasingly popular mode of travel in Canadian urban areas, like the Greater Toronto and Hamilton Area (GTHA). While trip origins and destinations can be inferred...     

A numerical study on piezoelectric energy harvesting by combining transverse galloping and parametric instability phenomena

This paper aims to numerically investigate the effects of parametric instability on piezoelectric energy harvesting from the transverse galloping of a square prism. A two degrees-of-freedom reduced-order model for this problem is proposed and numerically integrated. A usual quasi-steady galloping model is applied, where the transverse force coefficient is adopted as a cubic polynomial function with respect to the angle of attack. Time-histories of nondimensional prism displacement, electric voltage and power dissipated at both the dashpot and the electrical resistance are obtained as functions of the reduced velocity. Both, oscillation amplitude and electric voltage, increased with the reduced velocity for all parametric excitation conditions tested. For low values of reduced velocity, 2:1 parametric excitation enhances the electric voltage. On the other hand, for higher reduced velocities, a 1:1 parametric excitation (i.e., the same as the natural frequency) enhances both oscillation amplitude and electric voltage. It has been also found that, depending on the parametric excitation frequency, the harvested electrical power can be amplified in 70% when compared to the case under no parametric excitation.     

Plate scanning tools to obtain travel times in traffic networks

The management of vehicle travel times has been shown to be fundamental to traffic network analysis. To collect travel time measurement, some methods focus solely on isolated links or highway segments, and where two measurement points, at the beginning and at the end of a section, are deemed sufficient to evaluate users' travel time. However, in many cases, transport studies involve networks in which the problem is more complex. This article takes advantage of the plate scanning technique to propose an algorithm that minimizes the required number of registering devices and their location in order to identify vehicles candidates to compute the travel times of a given set of routes (or subroutes). The merits of the proposed method are explained using simple examples and are illustrated by its application to the real network of Ciudad Real.     

A havelock source panel method for near-surface submarines

A panel method is described for calculating potential flow around near-surface submarines. The method uses Havelock sources which automatically satisfy the linearized free-surface boundary condition. Outputs from the method include pressure field, pressure drag, wave resistance, vertical force, trim moment and wave pattern. Comparisons are made with model tests for wave resistance of Series 58 and DARPA SUBOFF hulls, as well as with wave resistance, lift force and trim moment of three length-to-diameter variants of the DSTO Joubert submarine hull. It is found that the Havelock source panel method is capable of determining with reasonable accuracy wave resistance, vertical force and trim moment for submarine hulls. Further experimental data are required in order to assess the accuracy of the method for pressure field and wave pattern prediction. The method is implemented in the computer code “HullWave” and offers potential advantages over RANS-CFD codes in terms of speed, simplicity and robustness.     

A non-geometrically similar model for predicting the wake field of full-scale ships

The scale effect leads to large discrepancies between the wake fields of model-scale and actual ships, and causes differences in cavitation performance and exciting forces tests in predicting the performance of actual ships. Therefore, when test data from ship models are directly applied to predict the performance of actual ships, test results must be subjected to empirical corrections. This study proposes a method for the reverse design of the hull model. Compared to a geometrically similar hull model, the wake field generated by the modified model is closer to that of an actual ship. A non- geometrically similar model of a Korean Research Institute of Ship and Ocean Engineering (KRISO)’s container ship (KCS) was designed. Numerical simulations were performed using this model, and its results were compared with full-scale calculation results. The deformation method of getting the wake field of full-scale ships by the non-geometrically similar model is applied to the KCS successfully.     

Experimental and numerical investigations on vibration characteristics of a loaded ship model

In this paper, vibration characteristics of the structure in the finite fluid domain are analyzed using a coupled finite element method. The added mass matrix is calculated with finite element method (FEM) by 8-node acoustic fluid elements. Vibration characteristics of the structure in finite fluid domain are calculated combining structure FEM mass matrix. By writing the relevant programs, numerical analysis on vibration characteristics of a submerged cantilever rectangular plate in finite fluid domain and loaded ship model is performed. A modal identification experiment for the loaded ship model in air and in water is conducted and the experiment results verify the reliability of the numerical analysis. The numerical method can be used for further research on vibration characteristics and acoustic radiation problems of the structure in the finite fluid domain.