Development and prospects of initial alignment method for strap-down inertial navigation system北大核心CSCD

Initial alignment technology is directly related to the navigation accuracy and startup time of the strap-down inertial navigation system (SINS), and has always been regarded as a challenging focal point in the research field of inertial navigation. This paper makes a comprehensive survey of SINS initial alignment technology, briefly introduces the basic principles of initial alignment without latitude, coarse alignment with known latitude and precise alignment, and points out their advantages, disadvantages and applicable conditions. The research and effects of existing initial alignment error suppression techniques are then analyzed and discussed. Finally, according to the problems of existing initial alignment methods and the development requirements of the carrier, the future research direction of SINS initial alignment technology is predicted. © 2022 Journal of Clinical Hepatology. All rights reserved.     

Influence of initial heeling angle on ship roll motion response北大核心CSCD

[目的]系统地研究初始横倾角对随机横浪下船舶横摇运动响应的影响。[方法]以路径积分法为基础,通过数值求解控制横摇运动微分方程概率属性的Fokker-Planck方程,得到横摇运动响应的概率分布。[结果]结果显示,初始横倾角对船舶横摇运动响应谱的影响有限,但对横摇角概率分布以及横摇运动响应极值分布的影响十分明显,且会造成船舶安全性的显著恶化。[结论]路径积分法可作为研究随机海浪下船舶横摇运动特性的有效数值方法。     

基于核磁共振与无侧限抗压试验对纤维加固红黏土的宏微观特性研究

红黏土因其具有孔隙比大、易压缩等不良工程特性,常在工程建设中引起一列工程问题.为此,采用聚丙烯纤维对红黏土进行加固,并采用核磁共振(NMR)技术和无侧限抗压强度试验对不同含量纤维加固后土体的宏微观特性进行测试,得到以下结论:1)不同含量纤维加固后红黏土的T2谱形态基本保持一致,均在弛豫时间为1 ms附近出现峰值,且纤维含量为0.2％时,试样内部信号最强;不同含量纤维加筋土内部的孔径主要分布在0.01μm到0.05μm之间,且0.02μm孔径所占比例最大;试样的孔隙度和T2谱峰值面积随纤维含量的增加表现出先增加后减小的趋势,且均在纤维含量为0.2％时到达最大值;2)纤维能够明显增加红黏土的抗压强度,加筋土的抗压强度与纤维含量保持良好的线性增加关系;且随着纤维含量的增加,试样由脆性破坏逐渐表现为韧性破坏特征.3)纤维在土体中起到加筋作用,显著增加了土体间的连接力,且纤维相互交叉连接形成了空间网状结构,限制了土体的变形,使得加筋土抗压强度增加并表现出韧性破坏特征.     

S^2 BHCA Multiple AUVs cooperation oriented control architecture

Oceanographic survey, or other similar applications should be the applications of multiple AUVs. In this paper, the skill ＆ simulation based hybrid control architecture （S^2BHCA） as the controller＇s design reference was proposed. It is a multi-robot cooperation oriented intelligent control architecture based on hybrid ideas. The S^2BHCA attempts to incorporate the virtues of the reactive controller and of the deliberative controller by introducing the concept of the ＂skill＂. The additional online task simulation ability for cooperation is supported, too. As an application, a multiple AUV control system was developed with three ＂skills＂ for the MCM mission including two different cooperative tasks. The simulation and the sea trials show that simple task expression, fast reaction and better cooperation support can be achieved by realizing the AUV controller based on the S^2BHCA.     

前导法顶进厚覆盖土大跨度箱涵施工技术

阐述前导法顶进大跨度箱涵的原理及方案设计,并结合工程实例,详细介绍在既有线厚覆盖土内采用前导法顶进大跨度箱涵的施工工艺及注意事项.     

三峡船闸(139m水位)一闸室船舶待闸研究

通过优化三峡船闸输水阀门运行参数,满足了船舶在一闸室待闸的停泊条件;组织代表船型进行实船试验,形成了连续调度快速安全的调度工艺,取得了在139m水位条件下,三峡船闸下行通航效率提高15%的效果。     

特种筒形桅杆风压试验

锥形筒形桅杆是一种新型桅杆 ,由于其结构的特点 ,风载可能对它产生较大的威胁。通过四面锥状筒型桅杆的风洞试验 ,研究了桅杆模型在不同风向下 ,在雷诺数 1 .7× 1 0 5 Re 7.8× 1 0 5的范围中 ,其周向与轴向的表面压力分布 ,给出了桅杆模型表面压力系数沿周向与轴向的变化规律 ,并作了分析 ,阐明了其与风向、雷诺数之间的关系。通过桅杆模型表面压力的周向积分 ,得到了模型的升力与阻力 ,导出升力系数与阻力系数 ,并分析了二者随雷诺数及风向的变化规律。试验分析结果表明 :压力系数沿轴向的分布不均匀 ,靠近桅杆模型的中间部位 ,压力系数较大 ;在桅杆模型的两端 ,压力系数较小。压力系数沿周向的分布与风向有关 ,在迎风面上 ,压力系数最大 ,在背风面上 ,压力系数最小。升力系数与阻力系数也与风向密切相关 ,并且随着风向的变化 ,有较大的变化。在筒型桅杆设计中 ,应充分考虑到风向变化所引起的风载变化。     

Active Roll Control for Passenger Cars

The development of a mathematical model of a limited bandwidth hydro-pneumatic suspension that is incorporated into a vehicle handling model is described. The combined model is used to evaluate a suitable control strategy for eliminating body roll during a cornering manoeuvre. The philosophy behind the roll control strategy has been to use feedback measurements of the body motions which do not compromise the ride control. A study of the influence of the position of the body motion feedback transducer on the effectiveness of the system to reduce the body roll is presented. Non-linear modelling of the suspension components for a 0.8g cornering manoeuvre has revealed performance limitations. Conclusions are drawn as to the effectiveness of the control scheme.     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Dynamic Simulation of a Smart Crank and Slider Mechanism

In this paper, a smart crank and slider mechanism is analyzed mostly from a dynamic view. By means of dynamic explicit finite element method, 3D nonlinear structure is simulated. It is proved that the mechanism can effectively accomplish smart movement prescribed. And in order to ensure reciprocal movement with higher frequency, measures should be taken to avoid over heating of parts. Compared with internal energy, kinetic energy of total rigid body is dominating, and Y direction equivalent rigid velocity is much higher than X direction velocity. Equivalent rigid velocity of all parts is consistent with respective movement condition. For both energy and velocity, slider effect is dominating. Three direction equivalent inertia force oscillates. Force amplitude in Y -direction is comparitively the greatest.