Gain and noise figure analysis of Er<Superscript>3+</Superscript>-doped YAG transparent ceramic microchip amplifier

The rate equations and the power evolution equations based on excited state absorption (ESA) and cooperative upconversion (CUC) of high concentration erbium-doped yttrium aluminum garnet (YAG) transparent ceramic waveguide amplifier are set up to analyze the effects of the pump power, active ion concentration and waveguide length on the amplifier gain and noise figure (NF). The numerical analysis predicts that with a pump power of 100mW, an active ion concentration of 1.0×10²⁶ ion/m³ and a waveguide length of 3 cm, a small-signal gain of 30 dB and an NF of 5 dB can be achieved in the micro-chip amplifier.     

Study of the helicopter blade running elevation measurement system

Helicopter blade running elevation measurement is an important measure target in helicopter blade dynamic balance experimentation. The elevation influences the helicopter＇ s security and other performance capabilities. In testing, however, it has been difficult to measure the elevation when the rotor reaches high speeds. To get a simple, fast and highly accurate measurement system, photo electricity technology was applied to measuring the blade running elevation. Discussed is the measurement principle of blade running elevation, tire design of the measurement system and analysis of the measurement precision.     

Course-keeping control of underactuated hovercraft

The course-keeping control of underactuated hovercraft with two aft propellers was considered. The control of the heading error and cross-track error was accomplished by the yaw torque merely in this case. The hovercraft dynamic model is nonlinear and underactuated. At first the Controllability of course-keeping control for hovercraft was proved, then a course-keeping control law was derived that keeps hovercraft heading constant as well as minimizes the lateral movement of hovercraft. The proposed law guarantees heading error and sway error all converge to zero exponentially. Simulation tests were carried out to illustrate the effectiveness of the proposed control law. For further research, the disturbance influence would be considered in the dynamic equations.     

Special requirements for alumina ceramic of ESG electrode bowl

At present ESG (Electrostatic Suspended Gyro) is the most precise inertia element in the world. The electrode bowl, which has direct effect on the precision of ESG, is a key part to ESG. Through the analysis of the function and characteristic of the electrode bowl in hollow rotor ESG and the present situation of new material development in the world, the alumina ceramic is regarded as the best material for the electrode bowl of hollow rotor ESG. By analyzing the present situation of alumina ceramic in the world, main technique requirements have been put forward for the alumina ceramic of ESG electrode bowl which is also fit for solid rotor ESG.     

上承式单肋拱桥稳定特性研究

该文以孙家凹桥为背景,讨论了上承式单肋拱桥的构造特点,研究了钢管混凝土拱肋刚度计算方法以及拱肋填充混凝土程度对其稳定特性的影响,得出结论,可为今后该类桥型的设计提供参考。     

浅谈基础设施项目工程造价全过程管理

分析了基础设施项目建设管理过程中存在的问题,阐明了对基础设施建设造价进行全过程管理的意义。运用工程项目造价全过程管理理论,即全生命周期造价管理理论,对基础设施项目建设造价进行全过程管理,并且详细分析了从项目的前期决策阶段到项目的实施阶段进行造价管理的方法。     

Gasket life criteria at low temperatures adopting proportional compensation for loss of flexibility and conformability

In the automobile industry, the service life of gaskets is defined as the time until which a released gasket recovers 60 % of the original compression. It was observed that the recovery curves of gaskets were highly nonlinear at high temperatures, and relatively nonlinear at temperatures above the room temperature. However, it was also noted that the recovery curves of the gaskets at temperatures below room temperature exhibited linearity with respect to the ln(time). Automotive manufacturers demand gasket life criteria that exceed a specific time or the entire life of a car. In the case of gaskets used at lower temperatures, since materials encounter losses in its flexibility and conformability, the definition of service life specifying a 60 % recovery may not be sufficiently safe to eliminate possible leakages. In this study, new gasket life criteria that could be used at low temperatures were proposed. The new criteria were proposed based on the change in Young’s modulus of the gasket material in order to conserve the sealing capability.     

Performance Design of an Exhaust Superheater for Waste Heat Recovery of Construction Equipment

Although fuel cost has been the largest portion of annual operating costs of construction equipment, it is possible to save the energy and reduce cost using fuel economy enhancement technology. In this study, an organic Rankine cycle is applied to an excavator in order to recover waste heat, reproduce it into electrical energy, and consequently reduce the fuel consumption by 10 %. A design process was carried out to develop an exhaust gas superheater that recovers the waste heat from exhaust gas through a composite-dimensional thermal flow analysis. A one-dimensional code was developed to perform a size design for the exhaust gas superheater. The ranges for the major design parameters were determined to satisfy the target of the heat recovery, as well as the pressure drop at both fluid sides. Performance analysis was done through onedimensional design code results, which were compared with three-dimensional CFD analysis. By utilizing a 3D commercial code, the arrangement of the tubes was selected and the working fluid pressure drop was reduced through a detailed layout design. The design procedure was verified by a performance evaluation of the prototype, which yielded only a 7 % tolerance in heat recovery.