青藏铁路大风天气运输组织方法

青藏高原大风天气多,空气密度小,大风对铁路运输安全的影响与低海拔地区差异较大。利用车辆动力学原理建立列车临界翻车风速模型,分别计算青藏铁路海拔3 000 m和4 000 m冻土和非冻土地区的临界翻车风速和危险翻车风速,以及给定风速条件下车辆限制速度。计算结果表明,青藏铁路临界翻车风速随海拔升高而增大,随冻土路基病害出现而降低。参考英、日等国大风标准,结合青藏铁路的特点,根据危险翻车风速和临界翻车风速,初步提出青藏铁路海拔4 000 m地区安全行车标准及特定运行条件、冻土地区线路出现病害情况下的安全行车标准及特定运行条件。提出列车限速运行、增加车辆载重、提高列车编组水平、提高司机操作水平、改善棚车顶部外形、加强货运检查、注意车辆防溜和风沙地区线路检查等大风天气运输组织措施。     

软土地基路堤临界高度确定方法探讨

软土地基上高速公路工程建设中存在路堤临界高度的现象,根据国内外已有的文献资料全面总结了路堤临界高度的3种确定方法:实测资料确定法、理论公式计算法和离心模型试验法。在此基础上,根据某高速公路的大量实测数据,利用多元线性回归分析方法,得到了一个路堤临界高度计算的经验公式,探讨了软土地基硬壳层和软土层厚度与路堤临界高度之间的内在联系。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Critical success factors of supply chain integration in container shipping: an application of resource-based view theory

ABSTRACT

The container shipping industry is receiving growing attention in driving the performance of global supply chains. This phenomenon has accelerated supply chain integration (SCI) within the industry. Although SCI could offer numerous benefits, it is often quoted to be implemented easier in theory than in practice. The high failure rate that is associated with SCI is often not addressed in the literature. Grounded on resource-based view (RBV) theory, this paper is aimed at identifying the critical success factors (CSFs) and examining their influence on SCI and supply chain performance (SCP). Survey questionnaires were administered on 164 container shipping firms. The constructs were validated empirically using confirmatory factor analysis and were subsequently analysed using structural equation modelling. The proposed CSFs in this study are found to be positively corelated with SCI, which, in turn, is positively correlated with SCP. This paper has contributed to both theory and practice by applying RBV theory to identify the key resources and capabilities that are necessary for SCI in the container shipping industry.     

Global cutting-path optimization considering the minimum heat effect with microgenetic algorithms

This article considers microgenetic algorithms (GAs), which explore in a small population with a few genetic operators, for cutting-path optimization problems. The major difference between GAs and simple genetic algorithms (SGAs) is how to make a reproductive plan for an improved searching technique because of population choice. It is shown that GAs implementation reaches the near-optimal region much earlier than the SGAs approach, and the GAs give a better solution than simulated annealing (SA). The main objective was to determine what temperature distribution can be obtained from the solution of a travelling distributed heat source. The solution of the travelling heat source on nested raw plate provides information about the vertices of each nested part of the raw plate. From the fact that the initial temperature at a piercing point strongly depends on the heat flow which stems from the previous cutting contour, the temperature of all piercing points must be lower than the critical temperature after each cutting of the components of a part. The critical temperature is identified as the mechanical melting temperature of steels. A heuristic back-tracking method is introduced to find the near-optimum cutting path considering the minimum heat effect on deformation. The heuristic back-tracking method is incorporated with the GAs.     

高速铁路通信信号设备接口雷电防护优化设计

提出了临界防护状态的概念,分析了临界防护状态使设备损坏的原因,提出高速铁路通信信号设备接口雷电防护优化设计方法,通过有效方法掌握被防护对象的耐冲击水平值和SPD各器件的耐受值,做到量化设计,保证防护的可靠性.     

吸能转向柱临界压缩力的设定

为防止或减少汽车碰撞对驾驶员的伤害,吸能转向柱得到广泛应用。文章通过对安全气囊气体发生器的反作用力和碰撞时方向盘下缘所受撞击力的分析,结合碰撞中不同情况下乘员头部和胸部对转向柱的撞击情况,确定了不同工况对吸能转向柱临界压缩力设定的影响,并最终指出如何结合安全带的选用及安全气囊的匹配情况来设定吸能转向柱的临界压缩力。     

CRCP路面裂缝间传荷能力影响评价

文章基于山东烟威高速公路连续配筋混凝土路面的基本结构参数,利用FWD实测CRCP路面不同破坏等级的裂缝间传荷系数,建立了三维有限元分析模型,分析了裂缝间不同传荷能力对CRCP路面临界应力的影响规律,并得到了CRCP路面最大应力与裂缝间传荷能力的关系式。     

潜艇薄壁大半径圆柱壳的总稳定性

本文指出了用仅受轴向压力的无肋光壳来预报各向均匀受压的异常环肋圆柱壳的总稳定性具有足够的精度，在薄壁大半径环肋圆柱总稳定模型试验中首次观察到了纵向失稳半波数m＝5，在纵横加肋圆柱壳总稳定模型试验中证明了在异常环肋圆柱壳上增设纵骨对提高总稳定性有巨大作用。此外，还指出了本文所推荐的纵横加肋圆柱壳总稳定理论临界压力公式是各种有关公式中最合适的计算公式．     

Delay Restoration of Single-Track Railway Rescheduling

On the basis of analysis of the principle of delay restoration in a disturbed schedule, a heuristic algorithm for rescheduling trains is developed by restoring the total delay of the disturbed schedule. A discrete event topologic model is derived from the original undisturbed train diagram and a back propagation analysis method is used to label the maximum buffer time of each point in the model. In order to analyze the principle of delay restoration, the concept of critical delay is developed from the labeled maximum buffer time. The critical delay is the critical point of successful delay restoration. All the disturbed trains are classified into the strong-delayed trains and the weak-delayed trains by the criterion of the critical delay. Only the latter, in which actual delay is less than its critical delay, can be adjusted to a normal running state during time horizon considered. The heuristic algorithm is used to restore all the disturbed trains according to their critical details. The cores of the algorithm are the iterative repair technique and two repair methods for the two kinds of trains. The algorithm searches iteratively the space of possible conflicts caused by disturbed trains using an earfiest-delay-first heuristics and always attempts to repair the earliest constraint violation. The algorithm adjusts the weak-delayed trains directly back to the normal running state using the buffer time of the original train diagram. For the strong-delayed trains,the algorithm uses an utility function with some weighted attributes to determine the dynamic priority of the trains, and resolves the conflict according to the calculated dynamic priority. In the end, the experimental results show that the algorithm produces ＂good enough＂ schedules effectively and efficiently in disturbed situations.