高压共轨喷油器精密偶件的泄漏分析

高压共轨电控喷油系统中，随着燃油喷射压力的大幅度提高，燃油的粘度-压力效应、粘度-温度效应凸显。作者分析了高压共轨喷油器精密偶件中的泄漏问题，得出的结论是：考虑了燃油的粘压效应、粘温效应后实际的泄漏量并不十分严重；如果考虑油液的极化效应、进口起始段的效应以及环形槽的影响，实际泄漏量可能还会减小。     

燃料电池电动车车载甲醇重整器

对目前世界几大汽车公司研制开发的燃料电池电动汽车车载甲醇重整器加以介绍，着重讨论了重整器的设计与重整催化剂的布置。指出，甲醇重整器的效果良好，但重整器出口富氢重整气中CO的含量仍然很高，而较高浓度的CO会使燃料电池电极中毒。因此，从重整器中产生出来的重整气在进入燃料电池以前要进行净化。     

军用半挂汽车列车的现状和发展趋势

介绍了国内外军用半挂汽车列车的发展现状,根据军用半挂汽车列车的运载对象和使用环境,分析了其性能特点、关键技术和发展趋势.     

多点电喷天然气发动机燃料喷射过程研究

数值模拟了从电喷天然气发动机喷射阀喷出的非稳态喷流的发展过程，并由纹影实验验证了解析方法的可行性。采用数值模拟的方法考察了天然气喷流贯穿距离与喷射压力和喷孔数的关系；以及喷射阀质量流量与喷射压力和环境压力的关系；为精确地控制天然气燃料喷射量提供了理论依据。最后数值模拟了进气歧管内天然气喷流的发展过程，探明了天然气喷射对发动机工作过程可能造成的影响。     

Experimental evaluation of Heavy Duty Vehicle speed patterns in urban and port areas and estimation of their fuel consumption and exhaust emissions

Exhaust emissions and fuel consumption of Heavy Duty Vehicles (HDVs) in urban and port areas were evaluated through a dedicated investigation. The HDV fleet composition and traffic driving from highways to the maritime port of Genoa and crossing the city were analysed. Typical urban trips linking highway exits to port gates and HDV mission profiles within the port area were defined. A validation was performed through on-board instrumentation to record HDV instantaneous speeds in urban and port zones. A statistical procedure enabled the building-up of representative speed patterns. High contrasts and specific driving conditions were observed in the port area. Representative speed profiles were then used to simulate fuel consumption and emissions for HDVs, using the Passenger car and Heavy duty Emission Model (PHEM). Complementary estimations were derived from Copert and HBEFA methodologies, allowing the comparison of different calculation approaches and scales. Finally, PHEM was implemented to assess the performances of EGR or SCR systems for NO_X reduction in urban driving and at very low speeds.The method and results of the investigation are presented. Fuel consumption and pollutant emission estimation through different methodologies are discussed, as well as the necessity of characterizing very local driving conditions for appropriate assessment.     

Closed-form multiclass cell transmission model enhanced with overtaking,lane-changing,and first-in first-out properties

A novel multiclass macroscopic model is proposed in this article. In order to enhance first-in, first-out property (FIFO) and transmission function in the multiclass traffic modeling, a new multiclass cell transmission model with FIFO property (herein called FM-CTM) is extended from its prior multiclass cell transmission model (M-CTM). Also, to enhance its analytical compactness and resultant computational convenience, FM-CTM is formulated in this paper as a set of closed-form matrix equations. The objective is to improve the accuracy of traffic state estimation by enforcing FIFO property when a fast vehicle cannot overtake a slow vehicle due to a limitation of a single-lane road. Moreover, the proposed model takes into account a different priority for vehicles of each class to move forward through congested road conditions, and that makes the flow calculation independent from their free-flow speeds. Some hypothetical and real-world freeway networks with a constant or varying number of lanes are selected to verify FM-CTM by comparing with M-CTM and the conventional CTM. Observed densities of VISSIM and real-world dataset of I-80 are selected to compare with the simulated densities from the three CTMs. The numerical results show that FM-CTM outperforms the other two models by 15% of accuracy measures in most cases. Therefore, the proposed model is expected to be well applicable to the road network with a mixed traffic and varying number of lanes.     

Changes in fuel economy: An analysis of the Spanish car market

This paper estimates the role that technological change and car characteristics have played in the rate of fuel consumption of vehicles over time. Using data from the Spanish car market from 1988 to 2013, we estimate a reduced form equation that relates fuel consumption with a set of car characteristics. The results for the sales-weighted sample of vehicles show that energy efficiency would have improved by 30% and 42% for petrol and diesel cars respectively had car characteristics been held constant at 1988 values. However, the shift to bigger and more fuel-consuming cars reduced the gains from technological progress. Additionally, using the results of the fuel equation we show that, besides a natural growth rate of 1.1%, technological progress is affected by both the international price of oil and the adoption of mandatory emission standards. Moreover, according to our estimations, a 1% growth in GDP would modify car characteristics in such a way that fuel consumption would increase by around 0.23% for petrol cars and 0.35% for diesel cars.     

Model based urban traffic control,part II: Coordinated model predictive controllers

The present paper describes how to use coordination between neighbouring intersections in order to improve the performance of urban traffic controllers. Both the local MPC (LMPC) introduced in the companion paper (Hao et al., 2018) and the coordinated MPC (CMPC) introduced in this paper use the urban cell transmission model (UCTM) (Hao et al., 2018) in order to predict the average delay of vehicles in the upstream links of each intersection, for different scenarios of switching times of the traffic lights at that intersection. The feedback controller selects the next switching times of the traffic light corresponding to the shortest predicted average delay. While the local MPC (Hao et al., 2018) only uses local measurements of traffic in the links connected to the intersection in comparing the performance of different scenarios, the CMPC approach improves the accuracy of the performance predictions by allowing a control agent to exchange information about planned switching times with control agents at all neighbouring intersections. Compared to local MPC the offline information on average flow rates from neighbouring intersections is replaced in coordinated MPC by additional online information on when the neighbouring intersections plan to send vehicles to the intersection under control. To achieve good coordination planned switching times should not change too often, hence a cost for changing planned schedules from one decision time to the next decision time is added to the cost function. In order to improve the stability properties of CMPC a prediction of the sum of squared queue sizes is used whenever some downstream queues of an intersection become too long. Only scenarios that decrease this sum of squares of local queues are considered for possible implementation. This stabilization criterion is shown experimentally to further improve the performance of our controller. In particular it leads to a significant reduction of the queues that build up at the edges of the traffic region under control. We compare via simulation the average delay of vehicles travelling on a simple 4 by 4 Manhattan grid, for traffic lights with pre-timed control, traffic lights using the local MPC controller (Hao et al., 2018), and coordinated MPC (with and without the stabilizing condition). These simulations show that the proposed CMPC achieves a significant reduction in delay for different traffic conditions in comparison to these other strategies.     

Influential vectors in fuel consumption by an urban bus operator: Bus route,driver behavior or vehicle type?

Energy costs account for an important share of the total costs of urban and suburban bus operators. The purpose of this paper is to expand empirical research on bus transit operation costs and identify the key factors that influence bus energy efficiency of the overall bus fleet of one operator and aid to the management of its resources.We estimate a set of multivariate regression models, using cross-section dataset of 488 bus drivers operating over 92 days in 2010, in 87 routes with different bus typologies, of a transit company operating in the Lisbon’s Metropolitan Area (LMA), Rodoviária de Lisboa, S.A.Our results confirm the existence of influential variables regarding energy efficiency and these are mainly: vehicle type, commercial speed, road grades over 5% and bus routes; and to a lesser extent driving events such as: sudden longitudinal decelerations and excessive engine rotation. The methodology proved to be useful for the bus operator as a decision-support tool for efficiency optimization purpose at the company level.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.