基于蠕滑机理的重载货车车轮磨耗研究

在多体动力学分析软件包SIMPACK中建立重载货车动力学模型,基于轮轨蠕滑机理在MATLAB软件中编制车轮踏面磨耗仿真程序WWS.根据车轮磨耗仿真结果和现场实测结果对Zobory磨耗模型进行修正.研究车辆非理想状态对车轮磨耗的影响,分析轮轨型面和转向架结构对车辆非理想状态的适应性.通过钢轨表面滚动接触疲劳损伤特征的研究,对车轮滚动接触疲劳和磨耗耦合关系进行数值模拟.主要研究内容和结论如下.     

基于激光位移传感器的车轮踏面磨耗检测方法研究

针对当前城轨车辆车轮踏面磨耗人工检测劳动强度高、检测精度低的问题,提出一种基于激光位移传感器的车轮踏面磨耗检测方法。首先在轨道外侧安装一组激光位移传感器进行车轮踏面数据采集;其次结合标准轮对踏面轮廓数据,采用数据预处理、坐标旋转、数据融合等算法获取实际车轮踏面轮廓线;最后根据踏面磨耗几何关系获得车轮踏面磨耗值。通过踏面磨耗检测误差分析以及现场标准轮对实验和过车实验表明,所提方法检测精度为±0.2 mm,抗干扰能力强,能够满足踏面磨耗检测实际要求。     

荧光磁粉探伤裂纹智能识别图像处理研究

磁粉探伤的发展趋势是自动化、智能化,而工件表面状况、真伪裂纹、工况条件等使得现有的检测识别方法难以满足工件表面裂纹缺陷自动检测识别的需要。在分析工件表面荧光磁粉图像特征及裂纹缺陷特征的基础上,研究表征裂纹邻域像素空间相关度的二维直方图分布,提出基于多重分块极值的图像边缘检测算法。根据裂纹邻域像素空间相关度参数,以及裂纹缺陷的长宽比、圆形度等特征,设计了基于Fisher线性判别方法的工件裂纹识别算法。以此为基础的荧光磁粉探伤工件裂纹缺陷自动检测识别技术,应用于列车轮轴检测线实时检测,裂纹缺陷的有效检出率达99%。     

HX_D1型机车牵引装置螺栓组应力数值模拟

对HXD1型机车牵引装置螺栓组加衬套前后的2种结构分别建立了有限元模型进行数值模拟计算,结果表明加衬套后螺栓的应力降低约一半,螺栓组利用率偏低。     

汽车车轮侧滑量检测存在问题及对策研究

在分析侧滑产生机理的基础上，论述了目前侧滑检测中存在的检测结果离散性大、判定失准等问题。指出产生这些问题的原因除车速、载荷、胎压等因素外，还包括侧滑台的技术状况、检测站的设计形式等因素。针对问题提出了稳定检测条件、合理制定标准、提高检测技术等实现侧滑量准确检测与正确评定的有效措施。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

大直径盾构隧道斜螺栓环缝抗剪特性研究

以大直径盾构隧道施工过程中管片上浮错台问题为背景,研究大直径盾构隧道环缝结构的抗剪特性,从结构承载力角度提出有效且可控的抗浮措施,并深入探究环间错台对隧道结构的影响,以确定大直径盾构隧道环间变形控制标准,减小隧道环间错台引起的管片损伤。以深圳妈湾跨海通道为依托,基于材料塑性损伤本构,考虑管片接缝细部构造,根据相关管片环缝剪切原型试验对接缝抗剪数值模拟方法的有效性进行验证。随后,利用数值模拟研究了环向接缝顺剪、逆剪和切向剪切时的错台现象和破坏特征,分析了斜螺栓、凹凸榫对环缝抗剪特性的影响,为大直径盾构隧道环缝结构的抗浮设计和安全评价提供依据。研究表明:环缝剪切错台数值计算结果与试验结果吻合良好,能够有效揭示接缝剪切过程中结构的变形特点和损伤特性;环缝接缝的剪切错台过程较为复杂,呈阶段性特征,螺栓和凹凸榫的受力状态是决定接缝抗剪特性的关键因素;凹凸榫能显著提高接缝抗剪刚度和承载力,但也带来接缝应力集中和张开过大等问题,设计和施工过程中需充分考虑接缝刚度和变形的适应性;基于环缝错台损伤分析,提出了环缝变形的三级安全评价指标,大直径盾构隧道接缝变形必须控制在Ⅱ级以内,以保证隧道的结构安全和正常使用性能。     

无轴轮缘推进器中可拆卸螺旋桨的性能分析

应用FLUENT数值模拟软件对无轴轮缘推进器螺旋桨进行水动力分析,根据实际运行工况需求确定数值模拟的基本方程、湍流模型、初始条件、边界条件、流体域以及网格划分等参数,建立相关数值模拟模型,计算出不同桨叶数目的螺旋桨在一定进速条件下的桨叶压力分布状况及螺旋桨推力与扭矩,并与常用经验公式计算结果进行比较,验证了无轴轮缘推进器螺旋桨有限体积元模型的正确性。研究结果可为该类型螺旋桨的优化设计提供理论支持。     

Nonlinear three-dimensional wagon-track model for the investigation of rail corrugation initiation on curved track

A nonlinear wagon-track model on curved track has been developed to characterize rail corrugation formation due to self-excitation of the wheel-rail stick-slip process. In this model, wagon movements were described using up to 78 degrees of freedom (DOFs) to model a three-piece freight bogie. Innovatively, the wheelset movements are described using nine DOFs, including torsional and bending modes about the longitudinal and vertical directions. The track modelling is considered as a one-layer structure (two rail beams on discrete spring and damper elements). The wheel sliding after creepage saturation is considered in the wheel-rail interface modelling. Simulation of a case study shows that the frequencies of the wheel stick-slip process are composed of the basic frequency, which might come from the combined effect of sleeper-passing frequency and one-third of the combined torsional and bending frequency of the wheelset, and the double and triple basic frequencies, which form the wavelengths of rail corrugation at different situations.