Critical review of handling diagram and understeer gradient for vehicles with locked differential

The steady-state cornering behaviour of rear-wheel drive vehicles fitted with locked differential is critically analysed by means of simple, albeit carefully formulated, vehicle models, which allow for a rigorous theoretical analysis. Results obtained for some classical manoeuvres, with either constant forward speed, steer angle or turning radius, clearly show that, in the case of locked differential, the vehicle cornering behaviour is strongly affected by the manoeuvre. As an important consequence, the handling diagram is not unique and the understeer gradient is no longer dependent only upon the lateral acceleration, as in vehicles equipped with an open differential. Accordingly, this study shows that some typical tools and concepts of vehicle dynamics are indeed inadequate in the case of locked differential.     

钢管桩与混凝土芯粘结力及抗弯应力传递模拟试验研究

依托深圳蛇口集装箱码头二期工程,进行了钢管桩与混凝土芯粘结力及抗弯应力传递模拟试验,对试验结果进行理论分析,讨论了不同搭接长度和不同UEA掺量对钢管桩与混凝土芯单位粘结力的影响;推导出纯弯矩作用下,混凝土芯与钢管粘结段粘结长度的计算公式。为类似工程提供方法指导和理论依据。     

湘潭湘江四大桥桩基混凝土的配合比设计及其应用

本文综述了湘潭湘江四大桥桩基混凝土配合比设计过程中对原材料的选择,及其在实际工程应用过程中灵活使用外加剂后掺法解决了外加剂与水泥适应性不良的问题,保证了工程的质量和施工进度。     

湿陷性黄土地基强夯和冲击压实技术经济分析

0引言湿陷性是指土在自重或附加应力与自重共同作用下受水浸湿后产生急剧而大量的下沉。国标中规定:当sδ≥0.015时,为湿陷性黄土。通常湿陷性黄土地基较多采用强夯法处理,其主要特点是适应性强,经济简便;而冲击压实技术是20世纪90年代从南非蓝派公司引进,具有减少工后沉降效果     

PCB生产中碱性蚀刻液补加工艺

从碱性蚀刻的化学反应机理出发,分析影响蚀刻精度的诸多因素,总结常规的蚀刻液补加工艺,提出了新的蚀刻液补加思路,并在实际生产中取得一定的效果.     

盾构法隧道纵向地震响应特性

采用土—结相互作用的动力有限元法,引入无长度的3自由度弹簧单元模拟纵向螺栓接头,分析行波波长、地基刚度与阻尼对盾构法隧道纵向地震响应的影响。分析结果表明:行波从水平方向输入时有突变弯矩产生,突变弯矩随波长和阻尼的增大而减小,而地基刚度系数对突变弯矩的影响相对较小;行波作用下,产生的接头最大轴力及最大弯矩值均随波长的增大而减小,而地基刚度系数及阻尼系数取值对最大弯矩值的影响较小。因此,建议在实际工程设计计算中要重视输入地震动参数的选择,且取较小的阻尼系数。     

《钢结构设计规范》在起重扒杆设计中的应用

在起重船扒杆设计中，现行《船舶及海上设施起重设备规范》没有提供直接强度计算方法，容易导致强度计算缺乏统一标准和审图产生困难。作者认为，《钢结构设计规范》（GB50017）提供的有关计算会式可作为船舶工程中起重扒杆以及其它压弯构件的计算方法。     

A review of the Effect of α/W ratio on fracture toughness （Ⅱ） experimental investigation in LEFM

In part I of this series, experimental investigation in EPFM （elastic-plastic fracture mechanics） had been discussed. In this paper, experimental investigation in LEFM （ linear elastic fracture mechanics） is given. Fracture toughness tests had been carried out on three different strength steels, using both through-cracked specimens with different α/W ratio and semi-elliptical cracked specimens with variable crack size and shape. Results show that the fracture toughness KIC increases with decreasing α/W when α/W 〈 0.3 for three-point-bend specimens, and that for α/W 〉 0.3, it is independent of α/W. Shallow crack specimens, both through-cracked and surface-cracked, gave markedly higher values than deeply notched specimens. However, the effect of crack shape on fracture toughness is negligible. Results also show that the LEFM approach to fracture is not tenable for design stresses where αc is often very small, far less than 2.5 （ KIC/σy）^2.     

关于规定曲率弯矩方程弯矩正负号的问题

阐明了曲率弯矩方程的物理概念及用此方程建立梁(柱)弯曲微分方程的思路,论述了在建立梁(柱)弯曲微分方程中规定弯矩正负号(简称这种规定)引起的问题:1)这种规定破坏了曲率弯矩方程所反映的物理概念及用曲率弯矩方程建立梁(柱)弯曲微分方程的思路;2)这种规定导致了梁(柱)截面内力矩与梁(柱)曲率正负号无关的错误概念;3)按这种规定建立梁(柱)弯曲微分方程须记住弯矩正负号的规定,与此种规定对应的坐标系,不考虑梁(柱)曲率的正负号等3条内容,否则得出错误结果。建议材料力学在阐述梁(柱)弯曲微分方程中删去这种规定,以避免上述问题。     

轨道交通曲线连续 钢—混组合梁抗剪分析

论述在钢混组合梁计算中,规范中按实体梁横向弯曲剪应力计算,没有扭转剪应力计算的规定。曲线组合梁的扭矩较大,讨论是否需要考虑扭转剪应力的影响。结合工程实例,计算分析自由扭转剪应力,按闭口薄壁构件和实体梁分别计算弯曲剪应力,并对计算结果进行对比分析,提出合理的计算方法。