硬咬合桩在含承压水复杂软土地层中的应用

通过上海某水厂基坑的咬合桩围护施工,分析了在含承压水的复杂软土地层中采用全套管全回转钻机进行硬切割成孔的咬合式排桩施工易出现的问题,以及采用的相应施工措施和施工要点,保证了工程的施工质量,为以后类似工程施工提供借鉴和参考.     

砂泥岩互层缓倾切向边坡应力特征及变形机理研究

为了更好地分析砂泥岩互层缓倾切向边坡的变形机理情况,以西南某红层边坡为例,基于数值模拟软件建立了软硬互层三维切向地质模型,探讨了边坡开挖、支护后的应力场和位移场。结果表明：砂泥岩互层切向边坡开挖后,边坡XX方向应力和YY方向应力出现了沿切向的锯齿形状,应力分布受岩层切向与互层岩性差异的影响较大,ZZ方向应力几乎不受影响;切向岩层受侧向约束的影响,致使边坡变形出现了层次性,且X方向较为显著,Y方向次之,Z方向最弱;边坡整体变形趋势类似于均质岩坡,呈现圆弧滑动趋势;边坡采用框架锚杆支护,仅起到构造护坡作用,边坡的变形和应力状态并未发生实质性的影响。研究成果对砂泥岩缓倾切向边坡的变形预测和支挡防护具有一定的工程借鉴意义。     

Effectiveness of travel time reliability indicators in the light of the assessment of dynamic managed lane strategy

ABSTRACT

The aim of traffic management is to ensure a high quality of service for a maximum number of users by decreasing congestion and increasing safety. Uncertainty of travel times decreases the quality of service and leads end users to modify their plans regardless of the average travel time. Indicators describing travel time reliability are being developed and should be used in the future both for the optimization and for the assessment of active traffic management operations. This article discusses the efficiency of certain reliability indicators in an ex-post assessment of a traffic management strategy. Ex-post assessment is based on an observational before–after study. As some factors other than the studied management strategy may intervene between the two periods, and as most reliability indicators require knowledge of the full travel time distribution and not only its average, a methodology is developed for the identification of the impact of these exogenous factors on the whole distribution. Many reliability indicators are split into different parts allowing the identification of the part due to the management strategy impact. The methodology is tested numerically on a managed lane operation consisting of Hard Shoulder Running (HSR) at rush hour on a section of a French motorway. The variation of some reliability indicators appears misleading, whereas the splitting of the indicators increases our understanding of the strategy and highlights its impact. The paper gives the reliability assessment of the HSR field test and discusses different reliability indicators to identify their potential performances and shortcomings.     

中国TBM施工技术进展、挑战及对策

总结我国近30年来TBM设计与施工技术的发展历程,可归纳为以下5个阶段:1)研发探索和试用阶段;2)以国外施工承包商为主体,采用国外设计制造TBM施工我国隧道工程阶段;3)独立进行TBM招标采购和选型设计,并建立起自主的TBM施工队伍阶段;4)与国外厂家联合设计制造TBM,工程应用和自主施工快速发展阶段;5)实现TBM国产化,面向国内外TBM工程市场自主施工阶段。通过我国不同时期TBM施工的典型工程,介绍我国在复杂地质、大坡度、高海拔、不同直径、不同机型、超长隧洞TBM施工方面取得的经验、技术积累和业绩,展示我国TBM在穿越断层破碎带、软弱变形、岩爆、涌水等不良地质洞段取得的一系列施工新技术,以及最高月进尺1 868 m、平均月进尺超过600 m和掘进作业利用率超过40%的掘进技术水平。分析TBM在极硬岩、大断层破碎带、软弱大变形围岩、强岩爆围岩、涌水突泥洞段、高地热隧洞和超长隧洞工程中施工面临的风险和挑战,并提出一些相应的技术措施和对策,期望这些措施和对策在未来大量实际工程中进一步得到实践验证、优化和改进,不断积累和创新TBM设计与施工新技术。     

汕头苏埃隧道方案设计关键技术研究

根据汕头苏埃隧道的建设条件,对工程方案设计中的几个技术难点进行研究,并提出解决方案。通过采用"多级分流"理念,实现隧道与北岸4条城市主干道的交通衔接;选择"抛石+排水板"方案解决海域深厚淤泥地层中的围堰设计;8度高烈度震区选择合理的抗震减震措施解决隧道结构抗震;采取双道密封垫和加大密封垫断面的防水设计,满足地震时管片接缝张开量大的防水要求;针对复杂地层,对盾构选型和配置提出建议;对海底凸起进入隧道内的硬岩进行爆破预处理,以降低盾构施工风险。     

海域围堰上软下硬地层中地下连续墙施工技术研究与实践

汕头市苏埃通道南岸明挖隧道位于海域围堰内,围堰内上软下硬的特殊地层给地下连续墙施工过程中的泥浆护壁、成槽造成极大的困扰。地下连续墙成槽施工前期主要采用"抓—冲结合"成槽工艺;在淤泥层、砂层、全风化岩层采用液压抓斗成槽机直接成槽;在强风化、中风化、微风化岩层采用冲击钻机冲孔、修槽成孔工艺。单元槽段成槽时一般完成1个槽段需要20 d以上,最长1个槽段达40 d,严重影响工期进度。为了改变地下连续墙施工状况,结合类似工程实践经验,在旋挖钻的基础上进行改造,将钻头设计为牙轮钻钻头,对强、中风化岩层钻孔取芯,通过组合使用"成槽机+冲击锤+旋挖钻(牙轮钻)"后,实现了地下连续墙施工效率的极大提升。经过成槽施工方案比选、入岩墙深设计优化、孤石破碎和基岩处理工艺探讨,顺利完成了该基坑工程,积累了在该类上部淤泥下部基岩地层中地下连续墙施工的经验。     

硬质颗粒含量对CNG阀座性能的影响

试验研究了硬质颗粒的含量对阀座的室温、高温硬度及压溃强度的影响,硬质颗粒对阀座烧结温度的影响,并通过模拟台架试验分析了硬质颗粒含量对阀座下沉量影响,综合确定了阀座材料中适宜的硬质颗粒含量。     

高埋深软硬岩互层地质条件下敞开式TBM岩爆段施工方法研究

基于喜马拉雅山区域某软硬岩性互层地质条件下的深埋隧洞工程,为解决该区域TBM施工过程中的岩爆问题,统计分析了TBM施工过程中的岩爆特征;在施工过程中开展了多种岩爆规避试验,形成了一套较完整的有针对性的施工方法： 1）岩爆风险巡查常态化; 2）超前地质预报和超前处理措施相结合; 3）支护材料和支护方式合理化; 4）掘进参数动态调整。在后续的施工中加以应用,取得了较好的效果,可以为类似地质条件下的安全施工提供参考。     

Analysis on the Characteristics and Development Trends of the Support Technology of High Ground Stress Tunnels in China北大核心CSCD

Combining the present situation and development trend of different tunnel support technologies at home and abroad, this paper analyzes the problems of rockburst in hard rock tunnels and large deformation in soft rock tunnels caused by high ground stress. It is concluded that: 1) regarding the rockburst problem, the current support technology is mainly influenced by the rock burst mechanism which is dominated by static factors, and so the used support components are generally of smaller deformation performance and "passive support" properties; 2) as the rockburst is the result of dynamic-static stress coupling, and only the anchor bolt has the "active support" attribute in the current "shotcrete+anchor bolt+wire net" support system, so the best support system should have the two functions of active support and energy release in terms of the rockburst problem, and the key focus of the research and development is anchorage members; 3) there are three main support types for large deformation in soft rock tunnels, e.g. the heavy support, layered support and yielding support. Among them, the heavy support system in underground cavern with large deformation is easy to induce excessive surrounding rock pressure, and so the applicable conditions are limited. The layered support system is still not the best choice due to its immature theoretical study, difficult determination of the thickness value and the installation time of each support layer and the interference to construction progress. With the characteristics of timely support and yielding while supporting, the yielding support system can give full play to the performance values of surrounding rocks and supporting materials, and make both of them reach the optimal state, so it is the best choice for supporting the soft rock tunnels with large deformations. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

疏浚硬质黏性土制作室内试验研究

基于疏浚工程中硬质黏性土挖掘困难和生产效率低的问题,为原状土进行刀齿的切削试验,需要制备硬质黏性土土质。针对疏浚吹填淤泥含水率大和压缩性强等特征,开发了一套底部抽真空的"真空+堆载"制备技术。试验研究表明:1)制备装置效果良好,制备土质标准贯入击数达到13击,液性指数达到0.36,疏浚岩土工程特性级别为4级,性质接近疏浚工程中给施工带来困难的黏性土质,为硬质黏性土的切削试验提供了合格的模型土质。2)制备土质含水率W与无侧限抗压强度R、标准贯入击数N、土体承载力F存在较好的相关性,回归系数均在0.72以上,为流塑等状态的软弱淤泥处理处置研究提供基础技术支撑。