汽车操纵动力学十八自由度模型仿真研究

本文介绍了根据多刚体动力学中的凯恩方法建立的一般两轴汽车的十八自由度数学模型。     

Modelling and control of a new differential steering concept

This paper presents a new steer-by-wire concept using an all-wheel drive vehicle layout with in-wheel motors while completely omitting the application of any dedicated steering device. Steering is based on the so-called differential steering principle which generates the necessary steering moment about the kingpins by a traction force difference between left and right sides of the vehicle. In order to investigate the behaviour of the vehicle and to design the underlying control algorithms, a planar vehicle model is presented, where the vehicle is described as constrained non-holonomic system requiring a special treatment. A state feedback linear controller for controlling of the lateral dynamics of the vehicle at higher speeds and a simple PI angle controller for low-speed manoeuvring are developed. The resulting behaviour of the system is investigated by various simulation experiments demonstrating a comparable steering performance of the new steering concept as that of conventional passenger cars.     

Multibody dynamics modelling of the freight train bogie system

Previous work in the railway technology laboratory at Virginia Polytechnic Institute and State University (Virginia Tech) focused on better capturing the dynamics of the friction wedge, modelled using three-dimensional rigid body dynamics with unilateral contact conditions. The current study extends the previous work to a half-bogie model treated as an application of multibody dynamics with unilateral contact to model the friction wedge interactions with the bolster and the sideframe. The half-bogie model was derived using MATLAB and functions as a three dimensional, dynamic, and multibody dynamics model comprised of four rigid bodies: a bolster, two friction wedges, and a sideframe assembly. This expanded model allows each wedge four degrees of freedom: vertical displacement, longitudinal displacement (between the bolster and sideframe), pitch (rotation around the lateral axis), and yaw (rotation around the vertical axis). The bolster and the sideframe are constrained to have only the vertical degree of freedom. The geometry of these bodies can be adjusted for various simulation scenarios. The bolster can be initialised with a pre-defined yaw (rotation around the vertical axis) and the sideframe may be initialised with a pre-defined pitch/toe (rotation around the lateral axis). The results of the multibody dynamics in half-bogie model simulation are shown in comparison with results from NUCARS^®, an industry standard in train-modelling software, for similar inputs.     

Wear simulation for the centre plate arrangement of a freight car

The bodies of many railway freight cars in many countries of the world are coupled to the running gear by means of a body centre plate that makes a friction pair with a centre bowl. During motion, the bogie is rotated and moved with respect to the car body. This leads to wear on the contact surfaces. Lubrication is inexpedient in this case because the friction forces damp the vibrations (so-called bogie hunting) during motion. Usually, centre plates exhibit noticeable wear after two years of operation. Reducing wear requires knowing details of the wear process which, in turn, requires computer simulation of freight car motion for an operation period of 10–15 years. The purpose of this paper is to develop a universal method for wear simulation of friction pairs that could be used, in particular, for the centre plate of a freight car.     

Investigating the influence of soil properties on railway traffic vibration using a numerical model

This paper presents the influence of dynamic and geometrical soil parameters on the propagation of ground vibrations induced by external loads. The proposed approach is based on a three-dimensional model, focusing on realistic excitation sources like impulse loads and moving railway vehicles. For the latter, a complete vehicle/track model is developed. The simulation is performed in time domain, offering an interesting approach, compared with classic cyclic analyses. The ground is modelled initially as an elastic homogeneous half-space and additionally as a layered half-space. First, the effect of homogeneous soil properties on ground vibration is analysed. Soil stratification is then taken into account, using various configurations. Analysis reveals that as receiver distance increases ground wave reflection in a layered ground plays an important role in the reduction of ground surface motion. This effect is magnified when the phase velocity wavelength becomes large compared with the depth of the surface layer.     

Influence of some vehicle and track parameters on the environmental vibrations induced by railway traffic

A study is performed on the influence of some typical railway vehicle and track parameters on the level of ground vibrations induced in the neighbourhood. The results are obtained from a previously validated simulation framework considering in a first step the vehicle/track subsystem and, in a second step, the response of the soil to the forces resulting from the first analysis. The vehicle is reduced to a simple vertical 3-dof model, corresponding to the superposition of the wheelset, the bogie and the car body. The rail is modelled as a succession of beam elements elastically supported by the sleepers, lying themselves on a flexible foundation representing the ballast and the subgrade. The connection between the wheels and the rails is realised through a non-linear Hertzian contact. The soil motion is obtained from a finite/infinite element model. The investigated vehicle parameters are its type (urban, high speed, freight, etc.) and its speed. For the track, the rail flexural stiffness, the railpad stiffness, the spacing between sleepers and the rail and sleeper masses are considered. In all cases, the parameter value range is defined from a bibliographic browsing. At the end, the paper proposes a table summarising the influence of each studied parameter on three indicators: the vehicle acceleration, the rail velocity and the soil velocity. It namely turns out that the vehicle has a serious influence on the vibration level and should be considered in prediction models.     

Dynamic analysis of a pantograph-catenary system using absolute nodal coordinates

The dynamic interaction between the catenary and the pantographs of high-speed trains is a very important factor that affects the stable electric power supply. In order to design a reliable current collection system, a multibody simulation model can provide an efficient and economical method to analyze the dynamic behavior of the catenary and pantograph. In this article, a dynamic analysis method for a pantograph-catenary system for a high-speed train is presented, employing absolute nodal coordinates and rigid body reference coordinates. The highly flexible catenary is modeled using a nonlinear continuous beam element, which is based on an absolute nodal coordinate formulation. The pantograph is modeled as a rigid multibody system. The analysis results are compared with experimental data obtained from a running high-speed train. In addition, using a derived system equation of motion, the calculation method for the dynamic stress in the catenary conductor is presented. This study may have significance in providing an example that a structural and multibody dynamics model can be unified into one numerical system.     

高速客车垂向悬挂稳定控制双振子模型机理研究

以Adams与Matlab作为协同仿真平台，基于双振子模型LQG控制器设计，建立了稳定控制方案和技术路线．仿真结果表明：垂向悬挂具有与双振子类似的隔振效果．尽管有横向和纵向相关运动模态的非线性影响，转向架仍可以实行有源／无源控制．仿真研究可以证实，无源控制转向架的系统机制是通过阻尼控制强制(垂向)主导运动模态处于稳定状态．     

Design and validation of a slender guideway for Maglev vehicle by simulation and experiment

Normally, Maglev (magnetic levitation) vehicles run on elevated guideways. The elevated guideway must satisfy various load conditions of the vehicle, and has to be designed to ensure ride quality, while ensuring that the levitation stability of the vehicle is not affected by the deflection of the guideway. However, because the elevated guideways of Maglev vehicles in South Korea and other countries fabricated so far have been based on over-conservative design criteria, the size of the structures has increased. Further, from the cost perspective, they are unfavourable when compared with other light rail transits such as monorail, rubber wheel, and steel wheel automatic guided transit. Therefore, a slender guideway that does have an adverse effect on the levitation stability of the vehicle is required through optimisation of design criteria. In this study, to predict the effect of various design parameters of the guideway on the dynamic behaviour of the vehicle, simulations were carried out using a dynamics model similar to the actual vehicle and guideway, and a limiting value of deflection ratio of the slender guideway to ensure levitation control is proposed. A guideway that meets the requirement as per the proposed limit for deflection ratio was designed and fabricated, and through a driving test of the vehicle, the validity of the slender guideway was verified. From the results, it was confirmed that although some increase in airgap and cabin acceleration was observed with the proposed slender guideway when compared with the conventional guideway, there was no notable adverse effect on the levitation stability and ride quality of the vehicle. Therefore, it can be inferred that the results of this study will become the basis for establishing design criteria for slender guideways of Maglev vehicles in future.     

树状多柔体系统动力学递推组集建模法

引入一种描述多柔体系统的随体坐标系,实现了刚体平动,刚体转动与弹性运动的分解,较好地消除了由于刚体大角度转动而产生的刚弹耦合非线性特性,根据约当变分原理,应用递推组集技术,由外层到内层逐层组装系统动力学方程,概括出一种树状多柔体系统动力学递推组集建模方法,降低了所需计算机存贮,最后给出了一个数值算例。