Development and prospects of initial alignment method for strap-down inertial navigation system北大核心CSCD

Initial alignment technology is directly related to the navigation accuracy and startup time of the strap-down inertial navigation system (SINS), and has always been regarded as a challenging focal point in the research field of inertial navigation. This paper makes a comprehensive survey of SINS initial alignment technology, briefly introduces the basic principles of initial alignment without latitude, coarse alignment with known latitude and precise alignment, and points out their advantages, disadvantages and applicable conditions. The research and effects of existing initial alignment error suppression techniques are then analyzed and discussed. Finally, according to the problems of existing initial alignment methods and the development requirements of the carrier, the future research direction of SINS initial alignment technology is predicted. © 2022 Journal of Clinical Hepatology. All rights reserved.     

Critical review of handling diagram and understeer gradient for vehicles with locked differential

The steady-state cornering behaviour of rear-wheel drive vehicles fitted with locked differential is critically analysed by means of simple, albeit carefully formulated, vehicle models, which allow for a rigorous theoretical analysis. Results obtained for some classical manoeuvres, with either constant forward speed, steer angle or turning radius, clearly show that, in the case of locked differential, the vehicle cornering behaviour is strongly affected by the manoeuvre. As an important consequence, the handling diagram is not unique and the understeer gradient is no longer dependent only upon the lateral acceleration, as in vehicles equipped with an open differential. Accordingly, this study shows that some typical tools and concepts of vehicle dynamics are indeed inadequate in the case of locked differential.     

隧道火灾三维数值模拟的瞬态分析

用连续方程、动量方程、能量方程及气体组分方程描述隧道内气流流动状态,采用湍流粘性系数模型中考虑浮力影响的湍流模型方程(K-ε方程),对某实验隧道火灾进行三维数值模拟瞬态分析,研究隧道火灾特性和烟气的速度场及温度场发展规律。研究结果表明,在横截面上先被加热的是拱顶,随着时间推移,高温烟气不断对其进行对流换热,整个横截面温度逐渐升高,且分布发生变化,经过一定时间后,分布形式基本确定,并向稳态逼近。采用3 m.s-1的机械通风,隧道内没有出现烟气逆流区,很好地抑制了气流的回流,满足隧道火灾通风要求,为上游人员及车辆逃离提供了气流通道。     

实测数据量大小对疲劳强度评估结果影响的研究

提速机车和客车的运用特点是全寿命时间长、运行线路条件相对固定。如何经济、有效地对结构疲劳强度进行评估是很重要的工作。首先介绍了疲劳强度评估的方法;其次,按不同的里程从全程数据中抽取数据并计算等效应力幅;最后通过对比分析,得出实测数据量大小对疲劳强度评估结果的影响程度,提出了经济、有效的采样方案。     

Ramp meters on trial: Evidence from the Twin Cities metering holiday

Ramp meters in the Twin Cities have been the subject of a recent test of their effectiveness, involving turning them off for eight weeks. This paper analyzes the results with and without ramp metering for several representative freeways during the afternoon peak period. Seven performance measures: mobility, equity, productivity, consumers’ surplus, accessibility, travel time variation and travel demand responses are compared. It is found that ramp meters are particularly helpful for long trips relative to short trips. Ramp metering, while generally beneficial to freeway segments, may not improve trip travel times (including ramp delays). The reduction in travel time variation comprises another benefit from ramp meters. Non-work trips and work trips respond differently to ramp meters. The results are mixed, suggesting a more refined ramp control algorithm, which explicitly considers ramp delay, is in order.     

船舶浮态计算方法及船舶浮态图谱

本文用化非线性问题为线性问题的线性化方法,对非线性隐式的船舶浮态方程组进行了数值解,并在深入研究的基础上提出了两种形式浮态图谱,以便能迅速而准确地确定船舶各种不同装载情况下的浮态。本文给出了五万吨油轮“西湖”号算例。     

肩回交路条件下多机牵引机车周转图的优化

针对采用机车肩回交路的重载铁路线路,将其列车运行图中的列车运行线转化为节点,机车周转线转化为边,运用机车转化为流,从而将机车周转图的优化问题转化为网络流问题.在此基础上,以运用机车数最少、单机走行数最少、附挂机车数最少、机车在站停留时间最短和机车工作均衡性最好为优化目标,以网络流问题中的节点流量守恒和节点流量要满足节点需求为约束条件,建立肩回交路条件下的多机牵引机车周转图多目标优化模型.按照优化目标函数的优先级,采用分层序列法对模型求解,并利用C#语言编写程序,通过调用ILOG CPLEX优化软件实现了该算法.算例表明,采用所给模型和据此编制的机车周转图优化程序,可以快速优化肩回交路条件下的多机牵引机车周转图.     

基于改进粒子群优化算法的鲁棒性列车运行图编制方法

以列车优先级、追踪运行间隔时间和连发间隔时间限制为约束条件,以旅客列车的走行公里总数、平均旅行速度、对标准计划的延迟总时间和延迟时间方差,以及货物列车的日车公里总数和日产最6个指标无量纲转化后的合计值最大为综合目标函数,建立列车运行图编制优化模型.为增加列车运行图的鲁棒性,引入虚拟车和缓冲时间槽2个参数,采用改进的粒子群优化算法给出鲁棒性列车运行图编制方法.以5个车站、5列旅客列车和7列货物列车构造模拟环境,采用该方法进行列车运行图编制模拟.结果表明:该方法可铺画出更优的列车运行图,计算效率高;在行车计划受到扰动后,虚拟车和缓冲时间槽释放资源,运行图可以较快地恢复到可接受范围,容错鲁棒性好.     

崩塌滑坡堵江堰塞湖灾害链铁路减灾选线策略

青藏高原南缘是崩塌滑坡堵江形成堰塞湖灾害链的高风险区,而我国铁路缺乏应对堰塞湖灾害的经验。铁路灾后改建工程线路优化设计将产生直接减灾效益,而新建铁路在选线阶段就采取一些主动减灾策略,也是风险调控的重要手段。为此,以中巴经济走廊中拟建哈维连至喀什铁路Attabad堰塞湖段为研究对象,根据堰塞湖灾害特点,通过将改建工程分段设计,并对不同改建线路方案进行技术经济指标比较,完成该段改建线路设计。基于上述工作,提出以有利地形控制溢流口开挖深度、宜尽量利用既有工程、在离开湖区后集中展线尽快与既有线联接、有条件时可提高限制坡度等灾后绕湖铁路选线设计要点与高位选线、酌情预留提高限坡措施的条件、尽量不跨河等新建铁路减灾选线设计策略,希望为铁路应对崩塌滑坡堵江堰塞湖灾害链提供参考。     

钢制车体疲劳强度校核方法

介绍了在缺乏材料疲劳性能数据时进行钢制车体疲劳强度校核的方法,从静态应力极限值和焊接疲劳数据的选取、Goodman疲劳极限线图的绘制方法、常用焊接接头类型、疲劳许用应力极限的确定、设计应用等方面对该方法进行了讨论。