微机控制的船用发电机继电保护实验装置

由于微机控制的继电保护与常规保护比较起来有许多优点,因此微机控制的船用发电机继电保护实验装置有其取代原有实验装置的必要性。本文就微机控制的船用发电机继电保护实验装置的硬件结构、软件算法和软件抗干扰技术进行了探讨。     

Experimental ivnestigation on flow fields of viscous fluid around two-dimensional wings and comparison with computational results

To examine the flow field of a viscous fluid around the trailing edge of a wing with respect to the Kutta condition or the Joukowski hypothesis, an experimental investigation into the velocity fields around two-dimensional (2D) wings NACA0012 and NACA4412 was carried out using an X-type hot-wire anemometer in a wind tunnel and the method of colored milk injection in a circulating water channel. The results of these investigations revealed that the flow of a viscous fluid at the trailing edge of a 2D wing is tangential to the face on the pressure side, and that the flow is very slow or reversed on the suction side due to separation when the angle of attack is greater than 7.5°. By flow visualization, a Kármán vortex street was found in the wake of both wings (NACA0012 and NACA4412) when the angle of attack was 5°. These results show that the ordinary Kutta condition with respect to the direction of outflow at the trailing edge is not necessarily satisfied in a viscous fluid, but the Kutta condition with respect to the pressure at the trailing edge is satisfied as usual. Numerical results, which have been obtained as the solution of Reynolds-averaged Navier-Stokes equations, show good agreement with above-mentioned experimental results. Therefore, CFD (Computational Fluid Dynamics) simulation has proved to be very effective for studying steady viscous flow around the trailing edge of a 2D wing.     

超高速实验车驱动方案设计及优化

研究速度在400-1000km／h的超高速实验车重接式电磁驱动方案,讨论重接式电磁驱动的电路结构和运动方程。在Maxwell3D瞬态场中搭建了驱动系统仿真模型,分析不同初始速度下,三级驱动系统受力特性和加速规律。针对系统运动特性和效率问题,提出驱动电路优化方案,使得发射体运动特性改善、效率提高。仿真结果表明：通过合理分配驱动单元,应用重接式电磁驱动的超高速实验车,可在短时间内被加速达到超高速的目标。     

Inventor参数化变压器三维结构设计

从铁道牵引变压器标准化的结构基本参数入手,利用Inventor软件采用Top-down设计思路,通过变压器基本参数建立结构骨架,然后与上级模块配合细化结构参数,完成初步结构设计,对结构优化完善,建立自适应模块,充实通用件库,最终完成总装配,生成与3D图参数关联的传统2D图纸,完成牵引变压器的设计。     

基于三维坐标测量轨道几何形位的计算模型

为改进基于CPⅢ轨道控制网测量技术的地铁无砟轨道几何形位精调的测量精度与效率,提出一种基于三维坐标测量轨道几何形位的方法。通过对轨道几何形位检测点进行三维坐标测量,以轨道控制网CPⅢ点作为测量基准点,采用轨道几何形位与检测点的三维解析几何关系,建立三维坐标测量轨道几何形位的计算模型。现场无砟轨道试验段的测试结果表明,三维坐标测量可有效对轨道几何形位进行测量,测量精度满足规范要求的无砟轨道几何形位测量精度指标。     

基于D2D技术的车车通信研究

阐述车车之间实现直接通信的应用价值和意义。利用列车在RBC中的注册数据(车次号)及同方向列车在区间内相对固定的运行顺序,在RBC端加入列车通信管理单元协助列车完成身份识别,并对特殊情况下的列车通信管理单元的布置原则进行分析。探讨利用D2D技术实现车车之间的信息互通,在结合C3线路列车的运行特征与D2D技术的模式特征后,选择D2D基站中继模式建立前后行列车的通信模型。在车车通信系统模型建立的基础上,对该系统的故障因素进行分析,利用马尔科夫模型对系统可靠性进行验证,结果显示其可靠性满足目前铁路运输的需求。     

The Reinforcement Analysis of Prestressed Anchor Frame Beam in the Deep Cutting Slope under Three Dimensional Strong EarthquakeEI北大核心

Research purposes: In order to further study the reinforcement of prestressed anchor frame beam in the deep cutting slope under three dimensional strong earthquake, a model of the deep cutting slope is built through FLAC 3D simulation software, the seismic wave to the model from three directions of x,y and z is input, and the dynamic response of the slope is analyzed. Then, the prestressed anchor frame beam reinforcement measures are applied to the model, and this paper analyzes the reinforcement effect of the prestressed anchor frame beam to the deep cutting slope under three dimensional strong earthquake. Research conclusions:(1) The prestressed anchor frame beam has a good effect on restraining the horizontal displacement of the deep cutting slope. (2) Under the three dimensional strong earthquake, the prestressed anchor frame beam has a good effect on the horizontal acceleration and horizontal velocity of the deep cutting slope, which reduces the peak of horizontal acceleration and horizontal velocity. (3) Through the comparison of the response before and after the reinforcement of the prestressed anchor frame beam is given under the 9 degrees three dimensional strong earthquake, it can be concluded that the prestressed anchor frame beam can provide good reinforcement effect to the deep cutting slope. (4) This research can be used for reference to the earthquake resistance of the slope engineering. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

基于轮廓线特征的三维人脸识别改进算法

研究基于面部轮廓曲线特征的三维人脸识别。为提取最优面部曲线特征,提出一种基于模糊聚类方法的人脸曲线特征优选算法。该算法从三维人脸深度图中选取最具代表性的8条轮廓曲线,作为主要识别特征,这在很大程度上降低了计算复杂度,克服表情和光照对人脸识别的消极影响,同时它用最少的轮廓线包含了所需要的人脸识别信息。基于这些人脸轮廓线特征,利用改进的Manhattan距离分类器来提高人脸识别的分类效果。实验结果表明,所提出的算法明显提高了人脸识别率,并且具有很强的鲁棒性。     

二三维一体化GIS在铁道部调度指挥系统中的应用研究

主要论述二三维一体化GIS技术在铁道部调度指挥系统中的应用方案,论述二三维一体化GIS技术的优越性,阐述铁道部调度指挥系统中二三维一体化GIS的平台选型、系统功能、设计方案,最后给出仿真环境下的系统效果,验证二三维一体化GIS技术在实际工程项目中的可行性。     

华盛顿地铁考察及对我国地铁建设的借鉴

通过对华盛顿地铁的实地考察,详细介绍华盛顿地铁的线路、车站的特点,阐述其在设计、运营、服务、节能等方面的主要理念以及实际措施,分析主要优缺点,并且对我国未来地铁的建设和运营提供建议。