Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

DK式顶管掘进机泥土仓土压力控制系统研究

顶管施工中，控制地面沉降是最关键的技术之一。而影响地面沉积的主要因素之一，是顶进过程中泥土仓内土压力的控制。本文以半盾构油缸为控制对象，通过调节油缸伸缩，最终来控制机头泥土仓土压力大小。经参数计算、数学建模、仿真分析、样机验证，证明效果良好。     

Experimental and numerical investigation on the derailment of a railway wheelset with solid axle

This paper presents the results of an experimental and numerical investigation on the derailment of a railway wheelset with solid axle. Tests were carried out under quasi-steady-state conditions, on a full-scale roller rig, and allowed to point out the effect of different parameters like the wheelset's angle of attack and the ratio between the vertical loads acting on the flanging and non-flanging wheels. On the basis of the test results, some existing derailment criteria are analysed in this paper and two new criteria are proposed. A model of wheel–rail contact is proposed for the mathematical modelling of the flange climb process, and numerical vs. experimental comparisons are used to obtain model validation.     

高压中和喷涂CFB锅炉三管防磨新工艺

CFB锅炉三管严重磨损引起国内、外专家们极大地关注。较详细地论述了三管磨损的原因，并提出了解决防磨新工艺、新材料。在6台CFB锅炉防磨实践中大大延长了使用寿命，取得成功。与当今国内、外所用的防磨技术相比，本技术的工艺与材料有独特的优越性：防高温氧化、耐硬物料粒子高速冲刷磨损、合金涂层结合密实牢固、抗冲击。该技术获国家发明专利。     

固体清除剂吸附CO_2容量的测定

固体清除剂吸附CO2容量常用的测定方法有流量法、重量法、量气法和滴定法。用这些方法对常温下LiOH、KO2、LiOH-KO2-Ca(OH)2和弱碱性纤维等固体清除剂吸附CO2的吸附容量进行分析。当动力学流程中总流量为30L、CO2浓度为1%;或密闭空间内通入CO2流量为120L/h时,由于吸附容量测试方法不同,固体清除剂吸附CO2容量的数值存在一定差异,其大小顺序为:流量法>重量法>滴定法>量气法。     

客车车架有限元分析及尺寸优化

以某客车车架为对象,利用HyperWorks建立了车架的有限元模型并对其进行了刚度和模态分析,在此基础上,以质量最小为目标,在不降低刚度和模态性能的前提下,对车架进行了尺寸优化。     

利用Authorware制作CAI课件

介绍了CAI课件的制作原则、过程及注意事项.     

工程变更对造价管理的影响研究

以FIDIC条款为基础，根据公平与效率原则阐述了工程变更过程中造价管理的原则和方法，并以示例进行了说明。     

Experimental and numerical investigation on the derailment of a railway wheelset with solid axle

This paper presents the results of an experimental and numerical investigation on the derailment of a railway wheelset with solid axle. Tests were carried out under quasi-steady-state conditions, on a full-scale roller rig, and allowed to point out the effect of different parameters like the wheelset's angle of attack and the ratio between the vertical loads acting on the flanging and non-flanging wheels. On the basis of the test results, some existing derailment criteria are analysed in this paper and two new criteria are proposed. A model of wheel-rail contact is proposed for the mathematical modelling of the flange climb process, and numerical vs. experimental comparisons are used to obtain model validation.     

微波溶样/原子吸收法测定铁路危货站固体废弃物中的重金属

参照美国ＥＰＡＳＷ８４６规定的标准方法，采用Ｑ－４５型微波溶样系统消解样品，原子吸收法测定铁路桃浦危险品货站固体废渣原样、浸滤渣样、浸提液样中的重金属Ｂｅ、Ｃｄ、Ｃｒ、Ｃｕ、Ｎｉ、Ｐｂ、Ｚｎ。研究了样品的消解条件、分析的最佳条件。各元素精密度实验的相对标准偏差在０．５４％～１２．８％，标准土样的测定回收率在７６．４９％～１０３．３３％。并报告了对上海铁路局桃浦危货站现场样品的测定结果。