Use of localized necking and fracture as a failure criterion in ship collision analysis

This study explores the use of localized necking for failure modeling in maritime crash analysis, using large shell elements. The assumption that the failure of a large shell element occurs simultaneously with the onset of localized necking is revisited. This study particularly investigates the numerical implementation of the localized necking condition and its implications on the results of ship collision analysis involving not only plate rupture but also various failure mechanisms such as the crushing and tearing of web girders, stringers, and their intersections. Through a series of large-scale collision simulations, the effects of bending deformation on the initiation of necking, non-proportional loading paths, and ductile fractures not preceded by localized necking, are investigated. It is demonstrated that a localized necking-based fracture model provides a reasonable, relatively mesh-insensitive estimate of the onset of fracture in the outer hull panels; however, fracture propagation is very sensitive to the numerical implementation of the necking and fracture model, especially for the cases involving the crushing of web frames and stringers.     

微机控制的船用发电机继电保护实验装置

由于微机控制的继电保护与常规保护比较起来有许多优点,因此微机控制的船用发电机继电保护实验装置有其取代原有实验装置的必要性。本文就微机控制的船用发电机继电保护实验装置的硬件结构、软件算法和软件抗干扰技术进行了探讨。     

舰用ICR燃气轮机PSR瞬态响应特性的数值分析

基于能量守恒原理和PSR（一次表面回热器）的结构特点，导出回热器冷热流体和固体问壁非稳态温度变化的微分方程式；利用直观的流动扰动因子M修正传热系数k，研究热流体进口温度和流量发生阶跃变化时PSR的响应时间；还分析了PSR传热波纹板片的数目，1、几何尺寸及通道波纹形状对温度响应时间的影响。研究结果表明，由于PSR的固体壁面时间常数远小于板翅式和管壳式换热器，因此这种轻重结构的先进换热器响应特性明显优于常规热交换器，特别适用于那些要求机动多变、反应灵敏的舰船和车用燃气轮机动力装置。     

日产VG30E发动机废气再循环系统的结构、工作原理及检修

日产VG30E发动机采用典型的电子控制废气再循环系统,其废气再循环系统的工作由微机集中控制系统(ECCS)根据相关传感器输入的信号进行控制。介绍了该系统的结构、工作原理及控制过程。在该系统的检修中,介绍了该系统工作情况的检查,控制阀的检修,电磁阀的检修,以及检修实例。     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

海上单桩风力发电平台简化设计

采用在欧洲已经进行商业化运作的独立桩双段结构，桩基础采用带有过渡段的单桩。塔架上的风力发电机采用丹麦Vestas公司的V80风力发电机。参考DNV-OS-J101和API-RP-2A中的工作应力设计法，进行结构静力、桩基础的承载力，涡激振动、疲劳寿命，结构动力学等分析。静力分析分析极端环境下的组合工况；桩基础主要计算桩的轴向承载力和校核水平承载力，并采用有限元模型模拟桩土相互作用；涡激振动分析主要考虑不同风速下塔架的升力以及引起的横向振动；疲劳分析根据涡激振动分析的结果利用S-N曲线对基础寿命进行了评估；动力学分析求出了结构的固有频率，并进行了波浪力作用下的瞬态历程分析。     

牙周炎患者红细胞免疫功能及发病机理研究

采用酵母菌花环试验对31例牙周炎患者红细胞免疫粘附功能、循环免疫复合物、补体C_3含量进行了检测,并与正常组进行了比较。结果显示:牙周炎患者红细胞膜免疫复合物及循环免疫复合物均升高,补体C_3含量降低,且皆与正常组有显著性差异。作者认为:免疫复合物在牙周炎发病机理中有一定的意义,牙周炎患者红细胞免疫对清除循环免疫复合物起着重要作用。     

Experimental ivnestigation on flow fields of viscous fluid around two-dimensional wings and comparison with computational results

To examine the flow field of a viscous fluid around the trailing edge of a wing with respect to the Kutta condition or the Joukowski hypothesis, an experimental investigation into the velocity fields around two-dimensional (2D) wings NACA0012 and NACA4412 was carried out using an X-type hot-wire anemometer in a wind tunnel and the method of colored milk injection in a circulating water channel. The results of these investigations revealed that the flow of a viscous fluid at the trailing edge of a 2D wing is tangential to the face on the pressure side, and that the flow is very slow or reversed on the suction side due to separation when the angle of attack is greater than 7.5°. By flow visualization, a Kármán vortex street was found in the wake of both wings (NACA0012 and NACA4412) when the angle of attack was 5°. These results show that the ordinary Kutta condition with respect to the direction of outflow at the trailing edge is not necessarily satisfied in a viscous fluid, but the Kutta condition with respect to the pressure at the trailing edge is satisfied as usual. Numerical results, which have been obtained as the solution of Reynolds-averaged Navier-Stokes equations, show good agreement with above-mentioned experimental results. Therefore, CFD (Computational Fluid Dynamics) simulation has proved to be very effective for studying steady viscous flow around the trailing edge of a 2D wing.     

柴油机排烟呈白色故障分析

文章以红岩6-250ZCD柴油机排烟呈白色为例子,介绍了故障现象及查找原因的过程,并对故障成因进行了剖析,有利于今后此类故障的快速确诊。     

"友谊号"FPSO生产工艺流程改造

“友谊号”FPSO经过升级改造变成一艘具有原油开发综合处理功能的中心平台。文章分别介绍了该FPSO改装后的原油处理系统、污水处理系统、伴生气和天然气处理系统的工艺流程。