东风4D改进型调车机车转向架设计

东风4D改进型调车机车是一种大功率调车机车，机车轴式为C0-C0，轴重为25t，主要用于大秦线万吨牵引的调车作业。介绍了该车转向架的总体布置、主要技术参数及结构特点。     

编组站驼峰车辆溜放速度控制系统的研究

以计算机和红外线传感器为主，研制了编组站驼峰车组溜放速度控制系统，系统通过检测车辆溜放的速度，计算出所需制动力的大小，通过缓器对车辆溜放进行速度控制，并具有对解体车辆自动计数，各种故障报警等功能。     

Using longitudinal methods for analysis of a short-term transportation demonstration project

This paper documents an application of panel, or longitudinal data collection in the evaluation of a TSM (Transportation Systems Management) demonstration project. The project was a four-week demonstration of staggered work hours in downtown Honolulu during February–March 1988. The 4 wave panel survey elicited commuting experiences of approximately 2,000 downtown employees at two week intervals before and during the project. The sample involved both employees who participated in the project by shifting their work hours, and those who did not. The panel survey was augmented by floating-car observations of travel times on major routes into downtown Honolulu on the same four dates.The purpose of the analysis was to determine whether employee commute times were affected, and if so, how these changes were distributed among various employee segments. Two methods were used. First, travel time changes were estimated using paired t-tests. Second, regression equations were used to estimate project time savings as a function of trip length, route, and location of residence. Results show that travel time savings due to the project were typically small, less than ten percent. Nonparticipants experienced greater savings than participants, and some segments of participants experienced longer travel times during the project. The panel method proved to be an effective way to measure project travel time impacts and shows that the method is appropriate in short time applications.Presented at the Annual Meeting of Transportation Research Board, January 7–11. 1990, Washington, D.C.     

基于沥青路面施工质量的设备合理匹配技术研究

现代高速公路施工不仅要以大规模机械化为基础,而且各机型之间需协调工作,形成与路面材料特性相适应的有机整体。通过对高速公路设备组成中核心设备的作业性能分析和试验研究,得出了摊铺机的合理作业工况,提出了以保证和提高路面施工质量为基础的施工机群合理匹配理论,并对核心设备、主要设备和辅助设备的合理配置进行了分析,给出了计算公式。     

异地协同设计在勘察设计中的应用

本文以铁三院为例,对异地勘察设计作业模式从“现场设计”发展到“异地协同设计”的实践、存在的问题及解决方法进行了分析。文中提到的部分方法已经在铁三院生产、管理中得到应用,并取得了较好的效果;对需进一步改进的问题也提出了解决方案。     

LTS2000装置在哈大线牵引变电所的应用

介绍了哈大线牵引变电所当地综合自动化控制系统中变电所220 kV侧系统自动转换、接触网线路自动检测和变电所馈线反向电压自动检测3种自动控制功能,分析了其基本原理、工作过程及应用情况和取得的效益.     

钢结构厚板母材及其焊接影响区的Z向冲击性能试验

为研究厚板及其焊缝在z向下的冲击性能,积累Z向冲击功的数据,为今后衡量评价z向性能提供实验依据,采用Q345B结构钢材,针对厚度60一165mm的板,在不同尺寸焊缝的十字形连接下沿轧制方向和板厚方向（z向）取样,在常温和低温下进行夏比y形缺1：2冲击试验。分析冲击功的变化规律,并用Bohzman函数进行拟合并分析韧脆转变温度。对试样断1：2进行电镜扫描分析。研究结果表明：z向取样,温度降低皆会对冲击韧性产生较大的影响,板厚及焊缝尺寸的增加也会对冲击韧性产生不利的影响,但相对较低。     

6502遇两相邻区段分路不良迎面误解锁问题分析

介绍6502电气集中定型电路遇轨道电路连续分路不良的故障积累情况下产生的危险侧输出,分析其原因,指出6502的限制性边界条件,提出关键的解决思路。     

浅析调车监控回放在STP故障分析及隐患排查中的运用

利用STP系统配套的地面处理软件新增的调车监控回放功能,可以查出区段分路不良、连挂异常等故障,这对调车作业过程中的故障分析及隐患排查有很大帮助。     

混合动力牵引调车机车的研发

阐述了混合动力牵引调车机车的概念和样车的结构性能,重点论述了样车主要研制内容及技术措施、节油减排效果、节油试验情况,从评估计算和试验验证两方面论证了混合动力技术能实现能量高效利用和循环利用的双重目标,总结了样车的研制成果。