高铁车站牵引电流损伤机械绝缘节原因探讨

高速铁路车站出现多次电气化牵引电流回流造成机械绝缘节和钢轨损伤的现象。根据现场的几次典型案例,对比分析电压损伤和电流灼伤2种情况的不同,为后续针对性的研究防护措施提供参考。     

涂层与阴极保护下的管道外腐蚀研究与控制

长期以来 ,一直认为管道在涂层和阴极保护协同保护下不会产生外壁腐蚀或腐蚀轻微。应用第三代高精度智能清管检测器对榕山—佛荫长为 2 5 4km的管线进行检测 ,发现了 455处外壁腐蚀 ,研究结果表明 :管道建设时 ,涂层施工的质量较差 ;使用维护过程中涂层材料老化严重、失修 ;管线上阴极保护系统长期故障使管道欠保护 ;执行了有严重缺陷的行业标准 ,至今不知管线上监测到的保护电位距真实的极化电位的差距有多大 ;管线的阴极保护度数据难以采集到。针对上述问题提出了控制腐蚀的方法。     

屈服假塑性流体管流流动及传热规律研究

结合屈服假塑性流体的本构方程、管流力平衡关系式以及非牛顿流体的能量方程，得出了屈服假塑性流体管流速度分布及温度分布。研究结果表明：由于屈服应力的作用，管中心存在柱塞流动，柱塞的半径与屈服应力成正比，与压力梯度成反比；管流流量随屈服应力的增大而减小；柱塞内温度一致，从柱塞边界到管壁，温度逐渐减小，而且越靠近管壁，温降梯度越大。     

弯管设计计算分析及研究

系统讨论了工程上影响弯管壁厚的因素 ,并在此基础上对工程上弯管设计计算的公式进行了推导、简化归纳 ,列出了计算公式中各参数的确定方法 ;最后通过实例对所推公式与工程上弯管计算公式进行了对比分析。     

计算管路摩擦因数的便捷方法

针对摩擦因数计算的现状与存在的问题 ,提出了采用MicrosoftExcel 2 0 0 0计算摩擦因数的方法。和传统的利用莫迪图或计算机编程的方法相比 ,Excel法计算可以省去查图的麻烦和繁杂的编程过程 ,提高了工作效率和计算精度。     

Dynamic loading history and collapse analysis of the pipe during deepwater S-lay operation

In the deepwater S-lay operations depending on the required stinger radius and rollers configuration, relatively large plastic deformation is induced when the pipe passes over the stinger, under the combined loadings of bending, axial tension, roller reaction force and the pipelay vessel motion. The resulting plastic deformation does not vanish after the pipe leaves the stinger. It accumulates until the pipe reaches the seabed. The inherited residual deformation might reduce the collapse capacity of the pipe under the external pressure loading. The present paper investigates the dynamic loading history of the pipe during the S-lay operation based on a test-verified finite element model, and then calculates the residual plastic deformation of the pipe cross-section after the pipe reaches the seabed. Finally, the nonlinear collapse analysis is implemented based on the modified RIKS method to evaluate the capacity of the installation-induced deformed pipe. The results confirm that the deepwater S-lay operation will lead to obvious plastic deformation of the pipe, which decreases the pipe collapse capacity to some extent.     

Comparative Analysis of Calculation Methods for Jacking Force of Jacking Pipes北大核心CSCD

Jacking force is the most important parameter in jacking pipe engineering, and reasonable calculation of jacking forces plays an important role in safe and smooth pipe jacking construction. There are many calculation methods for pipe jacking force at present, and the calculation results may be affected to some extent by different cal⁃ culation methods. For this reason, calculation methods of jacking force (frictional resistance) were collected and a comparative analysis was conducted with aspects to the advantages, disadvantages and applicabilities. The results show that as for the jacking force calculated by empirical formulae, the soil layer classifications corresponding to giv⁃ en frictional force per unit area and relevant factors to be considered are different, and the values of frictional force per unit area between pipe and soil in the same soil layer are also different; as for the jacking force calculated by theo⁃ retical formulae, the calculation methods for vertical earth pressure at crown are different and much effected by the pipe buried depth; as for the jacking force calculated by numerical simulation, the selected theories for the simula⁃ tion program and the construction factors to be considered during simulation are different. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

下穿公路隧道大管棚施工地表沉降研究

在采用管棚支护的隧道施工中地表沉降主要由管棚施工地表沉降和隧道开挖地表沉降组成。文章结合厦门高崎下穿公路隧道的工程实际,运用现场量测和理论分析的手段,对大管棚施工引起的地表沉降规律进行了研究;现场监测数据也证明,通过公式计算能有效地预测大管棚施工引起的地表沉降,其计算分析结果具有一定的实用价值。     

下穿既有公路的土江冲隧道双层管棚设计及监测分析

位于常—吉高速公路上的土江冲隧道是一座下穿既有公路的四车道连拱隧道,施工中为了控制地面沉降,在洞口段采用双层管棚作为辅助施工方法,保证了隧道施工安全和319国道的畅通;在隧道开挖过程中,掌子面附近的管棚变形最大,隧道开挖纵向影响范围为1.5~2.0倍开挖高度。文章介绍了管棚设计、施工情况和监测结果。     

BINGHAM流体环空管流流动及传热规律研究

结合BINGHAM流体的本构方程、管流运动方程及能量方程 ,推导了BINGHAM流体环空管流速度分布及温度分布。由于BINGHAM流体具有屈服值 ,环空管流流动中会形成流核。流核的宽度与屈服应力成正比 ,与广义压力梯度呈反比。流核中心线偏离环空中心线 ,且偏向环空内侧。环空内外径之比越小 ,相对偏离越远。在其他条件不变的情况下 ,当屈服应力增大时 ,速度分布剖面变得愈扁平。当其他条件不变时 ,流核速度随环空内外径之比减小而增大。流核内温度变化比环空内外侧明显小 ,随屈服应力的增大 ,温度分布剖面愈扁平。