多次喷射对柴油机燃烧与排放影响的试验研究

基于1台高压共轨涡轮增压柴油机,采用不同的预喷正时、预喷油量与后喷正时等,研究了多次喷射对燃烧放热、排放生成与燃油经济性的影响,以实现均质压燃和低温燃烧过程。研究结果表明:随预喷正时提前,缸内峰值压力降低,主燃阶段的滞燃期缩短,NOx和炭烟排放均降低;随预喷油量增加,预喷阶段燃烧的放热率和最大压力升高率增大,NOx和HC排放增大,而PM和CO排放降低;随后喷始点推迟,缸内压力与主放热率峰值差异变小,NOx排放降低,但炭烟排放先增大后逐渐降低。     

4JB1高压共轨柴油机开发研究

设计了4JB1柴油机共轨化的总体匹配方案和共轨柴油机的喷油量、共轨压力、喷射定时、预喷射等模块的匹配控制策略,分析了工况点使用频度对标定匹配中MAP步长和维数的影响。研究结果表明,采用变步长标定优化MAP,有效地提高了匹配效率,匹配后的发动机达到欧Ⅲ排放水平。     

柴油微引燃乙醇发动机燃烧、性能及排放特性研究

柴油微引燃乙醇发动机采用进气道喷射乙醇、缸内直喷微量柴油引燃的方式进行燃料供给。基于单缸四冲程柴油机,对其燃烧、性能及排放特性进行研究,固定引燃柴油喷射量为发动机能实现压燃着火的最小值,在进气压力为0.15 MPa时比较不同乙醇喷射量的工况组,通过改变柴油喷射时刻进行工况扫描。结果表明,引燃柴油的喷射时刻对发动机的燃烧、性能和排放影响显著。柴油微引燃乙醇发动机在中高负荷能够稳定运行,指示热效率可达34%以上,通过适当调节柴油喷射时刻,可以有效控制未燃碳氢(UHC)、NO_x与CO排放,同时可以实现极低的炭烟排放。柴油微引燃乙醇发动机燃烧模式为预混合或部分预混合燃烧,燃烧有两阶段放热特征,改变引燃柴油喷射时刻,可以有效控制燃烧相位。     

进气节流对柴油机低负荷性能影响的试验研究

在柴油机上加装节流阀是提升小负荷工况排温、改善排放的途径之一,但会对柴油机的其他性能造成影响。本研究通过给柴油机加装节流阀,研究了进气节流对柴油机小负荷工况性能的影响。试验结果表明:进气节流对柴油机的排温和NOx排放提升明显;柴油机进气节流后缸内压力下降,缸内平均燃烧温度、机械效率升高,滞燃期延长,燃烧始点后移;中低转速小负荷工况,随着节流程度的增加,燃油消耗率和烟度增加;高转速小负荷工况,一定范围内通过进气节流可以实现燃油消耗率和烟度的降低。2 500r/min,29N·m工况,保持EGR阀全开,随着节流程度的增加,NOx和烟度出现同时下降趋势,当空气流量由191.4kg/h降至140.6kg/h时,燃油消耗率、NOx、烟度分别下降了7.9%,58.1%,27.3%,排温提升了42.5%。     

Study of the effects on exhaust emissions in direct injection diesel engines: Effects of fuel injection system,distillation properties and cetane number

The effect of injection nozzle, diesel fuel density (volatility) and cetane number on diesel exhaust emissions were investigated. Decreasing injection nozzle hole diameter decreases PM emission. However, a small nozzle hole increases NO_x emission and decreases the effect of fuel on PM emission. Decreasing fuel density is effective for reduction of NO_x emission. But the effect is smaller than that of nozzle hole diameter and injection pressure. Furthermore injection timing retardation decreases the effect of fuel density on NO_x emission.     

喷油正时对电控共轨柴油机燃用LNG-柴油双燃料的影响

为了在电控共轨柴油机上应用LNG,将电控共轨柴油机改装为柴油引燃天然气双燃料发动机,研究了引燃柴油喷油正时对双燃料发动机性能与排放的影响。试验选取最大扭矩转速1 600r/min和标定转速2 500r/min,在不同油门开度工况下研究了双燃料发动机的功率、燃料消耗量、有效燃料消耗率和排放。试验结果表明:随喷油正时的提前,双燃料发动机的输出功率先增大后降低;有效燃料消耗率先降低后增大,并在最大功率正时处达到最低;HC,CO和炭烟排放降低,CO2排放升高;油门开度较小时的NOx排放降低,而油门开度较大时升高。     

Adaptation Strategy for Exhaust Gas Recirculation and Common Rail Pressure to Improve Transient Torque Response in Diesel Engines

Fuel injection limitation algorithms are widely used to reduce particulate matter (PM) emissions under transient states in diesel engines. However, the limited injection quantity leads to a decrease in the engine torque response under transient states. To overcome this issue, this study proposes an adaptation strategy for exhaust gas recirculation (EGR) and common rail pressure combined with a fuel injection limitation algorithm. The proposed control algorithm consists of three parts: fuel injection limitation, EGR adaptation, and rail pressure adaptation. The fuel injection quantity is limited by adjusting the exhaust burned gas rate, which is predicted based on various intake air states like air mass flow and EGR mass flow. The control algorithm for EGR and rail pressure was designed to manipulate the set-points of the EGR and rail pressure when the fuel injection limitation is activated. The EGR controller decreases the EGR gas flow rate to rapidly supply fresh air under transient states. The rail pressure controller increases the rail pressure set-point to generate a well-mixed air-fuel mixture, resulting in an enhancement in engine torque under transient states. The proposed adaptation strategy was validated through engine experiments. These experiments showed that PM emissions were reduced by up to 11.2 %, and the engine torque was enhanced by 5.4 % under transient states compared to the injection limitation strategy without adaptation.     

基于喷射正时的柴油机燃烧和排放研究

基于集成电控单体泵柴油机,讨论了喷射正时对柴油机燃烧及排放特性的影响规律。喷射正时对滞燃期和速燃期有显著的影响,从而影响放热规律、缸内压力和燃烧温度,进而对NOx和PM排放特性有显著的影响。在中大负荷下,随着喷射正时的滞后,放热率曲线相对于上止点的相位滞后,缸内最高燃烧温度下降,NOx排放下降,PM排放升高。在中小负荷下,随着喷射正时的进一步滞后,NOx和PM的排放同时下降。     

利用柴油机尾气后处理技术实现欧Ⅳ排放标准的试验研究

以某4缸增压直喷柴油机为样机,利用专业试验台架,在优化喷油提前角和EGR阀开度的前提下,联合利用氧化催化器(DOC)及微粒氧化催化转化器(POC)技术对柴油机尾气排放进行了试验研究,并总结了DOC和POC技术对柴油机排放的影响规律.试验结果表明,通过优化喷油提前角及EGR阀开度,并且选择正确的DOC与POC的布置形式,...     

Experimental study on the characteristics of nano-particle emissions from a heavy-duty diesel engine using a urea-SCR system

Particulate matter in diesel engine exhaust, particularly nano-particles, can cause serious human health problems including diseases such as lung cancer. Because diesel nano-particle issues are of global concern, regulations on particulate matter emissions specify that not only the weight of particulate matter emitted but also the concentration of nanoparticles must be controlled. This study aimed to determine the effects on nano-particle and PM emissions from a diesel engine when applying a urea-SCR system for NO_x reduction. We found that PM weight increases by approximately 90% when urea is injected in ND-13 mode over the emission without urea injection. Additionally, PM weight increases as the NH₃/NO_x mole ratio is increased at 250 °C. In SEM scans of the collected PM, spherical particles were observed during urea injection, with sizes of approximately 200 nm to 1 μm. This study was designed to determine the conditions under which nano-particles and PM are formed in a urea-SCR system and to relate these conditions to particle size and shape via a quantitative analysis in ND-13 mode.     

CA6110ZLA5车用柴油机达欧Ⅱ排放标准的试验研究

介绍了CA6110ZLA5车用柴油机的排放理论及控制方法。针对该机型提出了技术措施,通过提高喷射 压力,加快喷油速率,改善雾化质量,延迟喷油定时及匹配涡轮增压器等技术,进行优化配置试验,有效地降低了柴 油机NOx和PM排放,使该机型达到欧Ⅱ排放标准。     

基于液压驱动气门的柴油机性能优化研究

在某柴油机上将传统凸轮驱动气门机构改进设计为液压驱动气门机构,利用仿真软件GT-Power建立液压驱动气门柴油机模型,分析进气滞后角、排气提前角和气门重叠角对柴油机动力性的影响,然后以扭矩最大为目标对配气正时进行联合仿真优化,最后对比两种内部EGR实现方法在不同负荷下的EGR率和对NOx排放量的改善效果。研究结果表明,在外特性下,液压驱动气门柴油机在中低转速时的动力性和经济性有了明显改善,扭矩比原机提高了5.6%,燃油消耗率降低了5.1%;但由于液压气门响应滞后,随着转速的升高,改善效果逐渐降低。在转速2 000r/min时,排气门晚关比排气门早关可以获得更大的EGR率,NOx排放量降幅也比排气门早关的大,在50%负荷时,NOx排放量降幅最大为23.8%。     

燃油喷射参数对高压共轨柴油机性能的影响

运用GT—POWER软件建立了某高压共轨直喷柴油机的整机模型,并将计算值与试验值进行了比较,以确保模型具有足够的精度和可靠性;仿真分析了喷油压力、主喷提前角、预喷油量以及主预间隔对发动机性能的影响。仿真结果显示：增大喷油压力有助于提高发动机动力性和经济性并降低Soot排放;不同工况点需要选取不同的主喷提前角;增大预喷油量有助于降低NO。排放,但预喷油量不宜过大;主预间隔对Soot排放有较大影响。     

内部EGR及增压拓展柴油HCCI燃烧负荷范围试验研究

在135单缸柴油机上对比了传统燃烧模式和HCCI燃烧模式的负荷特性,优化了HCCI燃烧模式的喷油始点,分析了内部EGR率及增压压力对HCCI燃烧负荷范围及排放的影响。试验结果表明:对于负气门重叠期喷油的HCCI燃烧模式,1 500r/min下,最佳喷油始点为370°BTDC,气门重叠期为-30°时既保证了较低的NOx排放,又可以获得较佳的负荷范围;提高增压压力不仅可以拓展HCCI燃烧的负荷上限,对负荷下限的燃烧稳定性也有利;将增压压力提高到0.18MPa时,负荷上限从传统燃烧的0.594MPa上升到0.723MPa,但负荷下限较传统燃烧模式要高,CO排放、烟度和燃油经济性都较差。     

车用重型柴油机二级增压系统模拟及试验研究

针对某车用重型柴油机进行了二级增压系统匹配研究,根据产品开发目标要求选择了高、低二级增压器。采用GT-Power软件建立了二级增压柴油机仿真模型,并对柴油机外特性稳态工况性能进行了模拟计算,分析了二级增压系统能量分配对柴油机性能的影响规律。建立了二级增压柴油机测试平台,并进行了外特性、万有特性及排放特性试验。模拟及试验结果表明,二级增压系统可以大幅提高柴油机低速扭矩,改善燃油经济性,拓宽柴油机燃油经济性运行区域,大幅降低柴油机PM排放。     

直喷式柴油机燃用甲醇燃料的排放特性的研究

本文通过在１１３０单缸柴油机上燃用全甲醇的试验。     

CNG/柴油双燃料车用发动机排放特性研究

通过用YZA102Q柴油机改装的CNG／柴油双燃料发动机进行燃用双燃料和纯柴油两种情况下的对比试验。对CNG／柴油双燃料发动机THC、CO、NOx和烟度的排放特性，以及空燃比、引燃油量、喷油提前角对双燃料发动机排放的影响进行了研究和分析。     

生物柴油-柴油-乙醇混合燃料的燃烧与排放特性

为了改善发动机燃用高比例生物质混合燃料的性能,在中等比例的生物柴油-柴油混合燃料中分别添加5%、10%和20%体积比的乙醇（分别用BD50E5,BD50E10和BD50E20表示）,在一台6缸增压共轨柴油机上,将发动机的转速稳定在1 600 r·min^-1,选择7个不同的负荷点测定不同掺混比生物柴油-柴油-乙醇混合燃料的燃烧与排放性能,并将其与柴油进行对比。结果表明：在平均有效压力为0.322 MPa的低负荷条件下,发动机为预喷加主喷喷油策略,在预喷的低温反应阶段生物柴油-柴油-乙醇混合燃料产生了大量羟基自由基,因此混合燃料的缸内最大压力和最大瞬时放热率均高于柴油;随着负荷的增大,当平均有效压力为0.805 MPa时,发动机的喷油策略转变为单段喷射,乙醇的热值较低导致生物柴油-柴油-乙醇混合燃料的缸内最大压力和最大瞬时放热率低于柴油;随着乙醇掺混比的增大,受乙醇低十六烷值和高汽化潜热的影响,生物柴油-柴油-乙醇混合燃料的滞燃期明显延长;强烈的预混燃烧和乙醇的高含氧量使混合燃料的燃烧速度明显加快,乙醇的添加有利于燃料集中放热从而缩短燃烧持续期;与纯柴油相比,BD50E5,BD50E10和BD50E20的NO_x排放量分别升高了10.46%、12.59%和17.52%,碳烟排放量分别降低了37.91%、45.85%和49.25%,CO排放量分别降低了20.24%、36.43%和46.43%,HC排放量分别降低了12.53%、4.40%和0.76%。     

Influence of pilot injection on combustion characteristics and emissions in a DI diesel engine fueled with diesel and DME

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion and emissions characteristics (NOx, CO, THC and smoke) in a single-cylinder DI diesel engine. The experiments were conducted using two fuel injection systems according to the fuel type, diesel or dimethyl ether (DME), due to the different fuel characteristics. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (?4°CA aTDC, ?2°CA aTDC, 0°CA aTDC, 2°CA aTDC and 4°CA aTDC). Results from pilot-main injection conditions are compared with those shown in single injection conditions to better demonstrate the potential of pilot injection. It was found that pilot injection is highly effective for lowering heat-release rates with smooth pressure traces regardless of the fuel type. Pilot injection also offers high potential to maintain or increase the BMEP; even the combustion-timing is retarded to suppress the NOx emission formation. Overall, NOx emission formation was suppressed more by the combustion phasing retard effect, and not the pilot injection effect considered in this study. Comparison of the emissions for different fuel types shows that CO and HC emissions have low values below 100 ppm for DME operation in both single injection and pilot-main injection. However, NOx emission is slightly higher in the earlier main injection timings (?4°CA aTDC, ?2°CA aTDC) than diesel injections. Pilot injection was found to be more effective with DME for reducing the amount of NOx emission with combustion retardation, which indicates a level of NOx emission similar to that of diesel. Although the diesel pilot-main injection conditions show higher smoke emission than single-injection condition, DME has little smoke emission regardless of injection strategy.     

不同喷油模式下柴油机可用能分析的试验研究

通过台架试验的方法,对1台0.5L单缸柴油机进行了热力学分析,将缸内燃烧所释放能量的热量分布和可用能分布进行计算和比较,在此基础之上比较了喷油规律相关参数对热平衡的影响,提出了相应减少不可逆损失、提升热效率的解决途径。试验结果表明:在相同工况下,对于不同的喷油模式,燃烧不可逆损失差异不大,差异主要体现在排气损失和其他部分损失;预喷参数和后喷参数对热量分布影响较小,而喷油压力和主喷正时的影响较为明显。随着喷油压力的增大或主喷正时的提前,燃烧不可逆程度降低,排气可用能损失减少,热力循环的热效率得以提升。而对于余热能回收,排气中流失的可用能回收的潜力和价值较大,将这一部分能量妥善地利用可对整机性能起到明显的改善效果,若排气温度从750K降至500K,通过排气余热能的利用可提升指示功20.91%,达到提升动力性和燃油经济性的目的。