A traffic noise model for road intersections in the city of Cartagena de Indias,Colombia

Road traffic noise models are fundamental tools for designing and implementing appropriate prevention plans to minimize and control noise levels in urban areas. The objective of this study is to develop a traffic noise model to simulate the average equivalent sound pressure level at road intersections based on traffic flow and site characteristics, in the city of Cartagena de Indias (Cartagena), Colombia. Motorcycles are included as an additional vehicle category since they represent more than 30% of the total traffic flow and a distinctive source of noise that needs to be characterized. Noise measurements are collected using a sound level meter Type II. The data analysis leads to the development of noise maps and a general mathematical model for the city of Cartagena, Colombia, which correlates the sound levels as a function of vehicle flow within road intersections. The highest noise levels were 79.7 dB(A) for the road intersection María Auxiliadora during the week (business days) and 77.7 dB(A) for the road intersection India Catalina during weekends (non-business days). Although traffic and noise are naturally related, the intersections with higher vehicle flow did not have the highest noise levels. The roadway noise for these intersections in the city of Cartagena exceeds current limit standards. The roadway noise model is able to satisfactorily predict noise emissions for road intersections in the city of Cartagena, Colombia.     

Evaluating effects of traffic and vehicle characteristics on vehicular emissions near traffic intersections

Urban air quality is generally poor at traffic intersections due to variations in vehicles’ speeds as they approach and leave. This paper examines the effect of traffic, vehicle and road characteristics on vehicular emissions with a view to understand a link between emissions and the most likely influencing and measurable characteristics. It demonstrates the relationships of traffic, vehicle and intersection characteristics with vehicular exhaust emissions and reviews the traffic flow and emission models. Most studies have found that vehicular exhaust emissions near traffic intersections are largely dependent on fleet speed, deceleration speed, queuing time in idle mode with a red signal time, acceleration speed, queue length, traffic-flow rate and ambient conditions. The vehicular composition also affects emissions. These parameters can be quantified and incorporated into the emission models. There is no validated methodology to quantify some non-measurable parameters such as driving behaviour, pedestrian activity, and road conditions     

Network-wide traffic and environmental impacts of acceleration and deceleration among Eco-Driving Vehicles in different road configurations

Eco-Driving, a driver behaviour-based method, has featured in a number of national policy documents as part of CO₂ emission reduction or climate change strategies. This investigation comprises a detailed assessment of acceleration and deceleration in Eco-Driving Vehicles at different penetration levels in the vehicle fleet, under varying traffic composition and volume. The impacts of Eco-Driving on network-wide traffic and environmental performance at a number of speed-restricted road networks (30?km/h) is quantified using microsimulation. The results show that increasing levels of Eco-Driving in certain road networks result in significant environmental and traffic congestion detriments at the road network level in the presence of heavy traffic. Increases in CO₂ emissions of up to 18% were found. However, with the addition of vehicle-to-vehicle or vehicle-to-infrastructure communication technology which facilitates dynamic driving control on speed and acceleration/deceleration in vehicles, improvements in CO₂ emissions and traffic congestion are possible using Eco-Driving.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

Noise prediction for highways in Thailand

A model of highway traffic noise is formulated based on vehicle types. The data were collected from local highways in Thailand with free-flow traffic conditions. First, data on vehicle noise was collected from individual vehicles using sound level meters placed at a reference distance. Simultaneously, measurements were made of vehicles’ spot speeds. Secondly, are data for building the highway traffic noise model. This consists of traffic noise levels, traffic volumes by vehicle classification, average spot speeds by vehicle type, and the geometric dimension of highway sections. The free-flow traffic noise model is generated from this database. A reference energy mean emission level (the basic noise) level for each type of vehicles is developed based on direct measurement of Leq (10 s) from the real running condition of each type of vehicles. Modification of terms and parameters are used to make the model fit highway traffic characteristics and different types of vehicle.     

Modal analysis of real-time,real world vehicular exhaust emissions under heterogeneous traffic conditions

This study presents the characteristics of real world, real time, on-road vehicular exhaust emission namely, carbon monoxide (CO), nitric oxide (NO), hydrocarbons (HC), and carbon dioxide (CO₂) emitted under heterogeneous traffic conditions. Field experiments were performed on major category of vehicles in developing countries, i.e. two-wheelers, auto-rickshaws, cars and buses. The on-board monitoring was carried out on different corridors with varying road geometry. Results revealed that the driving cycle was dependent on the road geometry, with two lane mixed flow corridor having lot of short term events compared to that of arterial road. Vehicular emissions during idling and cruising were generally low compared to emissions during acceleration. It was also found that emissions were significantly dependent on short term events such as rapid acceleration and braking during a trip. Also, the standard emission models like COPERT and CMEM under predicted the real world emissions by 30–200% depending upon different driving modes. The on-road emissions measurements were able to capture the emission characteristics during the micro events of real world driving scenarios which were not represented by standard vehicle emission measured at laboratory conditions.     

Options for reducing noise from roads and railway lines

The fundamental noise generation mechanisms of road and rail vehicles are discussed with attention to noise abatement measures. Based on an evaluation of publicly available tire noise data and the European road traffic noise emission model CNOSSOS, it is shown that on the road side there is a significant noise reduction potential in the usage of low-noise tires. From a three months measurement campaign a noise model was derived to predict the maximal sound pressure level of heavy duty vehicles during a pass-by in 7.5 m distance with the parameters vehicle speed and number of axles. With help of recently published information about external costs caused by heavy duty vehicles and the noise prediction tool, a model was developed to derive a money equivalent that can be used as a bonus/malus in a heavy duty vehicle fee. As a measure at the infrastructure, the installation of low-noise pavements is an effective, durable and economically attractive measure. Recent experiences with different technologies from all over the world are compiled and evaluated. On the rail side, an overview of the possible noise reduction strategies is given, followed by a discussion of the current policy and legislation in the EU and on the national level of different European countries.     

城市桥梁声屏障设计及交通噪声控制研究

城市桥梁交通噪声污染随着城市道路的发展和车辆增多日益严重,引起了人们的普遍关注。文章以北大桥声屏障设计为研究对象,结合北大桥交通噪声污染调查分析,阐述了声屏障高度、声屏障结构形式等声屏障设计治理方案,并从规划阶段、运营阶段等方面探讨了城市桥梁交通噪声的控制对策。     

Variability in sound power levels: Implications for static and dynamic traffic models

Classically, one mean vehicle representative of each category is used by both static and dynamic traffic noise prediction models. The spectrum associated with this mean vehicle is determined from a linear statistical regression analysis based on measurement campaigns on a track or in situ. However, the variability of individual vehicle emissions can influence predictions and hinder comparison between static and dynamic models. In order to estimate the induced bias, statistical analysis of the distributions of sound power levels emitted by the individual passage of vehicles during 82 measurement campaigns was carried out. The results show that 92% of the residual regression distributions are Gaussian and that standard deviations can reach 3.6 dBA. The value of the proposed correction term for this case study could reach 1.4 dBA for light vehicles and 1.2 dBA for heavy vehicles. This analysis also shows that the variability in sound power levels and thus the corresponding corrections are higher at the lowest speeds that correspond to urban driving conditions.     

Modeling traffic noise in a mountainous city using artificial neural networks and gradient correction

Different regions have established traffic noise prediction models to adapt to their particular environmental characteristics. This paper aimed to develop a traffic noise prediction model for mountainous cities. In China, the traffic noise prediction model HJ 2.4-2009, which itself is based on the sound pressure level corrected for roadway gradients (RGs), has been receiving widespread acceptance. On the basis of the model in HJ 2.4-2009, the RG correction coefficient was proposed to modify the original model and a per-vehicle noise prediction model was built using a multilayer feedforward artificial neural network (ANN) model. The data collected from a municipal road of a hilly city, Chongqing, was used to train and validate the ANN model. The predictor variables comprised the per-vehicle noise value, vehicle type, vehicle velocity, and roadway gradient. The results showed that the modified HJ 2.4-2009 model incorporating the gradient correction coefficient achieved a significantly higher R² for mountainous cities than the original model. Besides, the ANN-based noise prediction model achieved considerable accuracy improvement over the empirical predictive equations.     

GPS-based speed collection method for road traffic noise mapping

One of the most difficult and expensive tasks in making noise pollution maps is the collection and processing of the data needed to create acoustic models. In the case of road traffic noise maps, obtaining speed data for light and heavy vehicles a problem that has usually been avoided by using a road’s speed limit or by making assumptions based on experience from similar road types. Here global positioning systems-based techniques are applied for acquiring vehicle speed data and adapted to fulfill the requirements of noise prediction models.     

Does winter road maintenance help reduce air emissions and fuel consumption?

Winter road maintenance (WRM) has been shown to have significant benefits of improving road safety and reducing traffic delay caused by adverse weather conditions. It has also been suggested that WRM is also beneficial in terms of reducing vehicular air emissions and fuel consumptions because snow and ice on road surface often cause the drivers to reduce their vehicle speeds or to switch to high gears, thus decreasing fuel combustion efficiency. However, there has been very limited information about the underlying relationship, which is important for quantifying this particular benefit of a winter road maintenance program. This research is focused on establishing a quantitative relationship between winter road surface conditions and vehicular air emissions. Speed distribution models are developed for the selected Ontario highways using data from 22 road sites across the province of Ontario, Canada. The vehicular air emissions under different road surface conditions are calculated by coupling the speed models with the engine emission models integrated in the emission estimation model - MOVES. It was found that, on the average, a 10% improvement in road surface conditions could result in approximately 0.6–2% reduction in air emissions. Application of the proposed methodology is demonstrated through a case study to analyse the air emission and energy consumption effects under specific weather events.     

Urban road traffic noise spatiotemporal distribution mapping using multisource data

Many residents are disturbed by road traffic noise which needs to be controlled and managed. The noise map is a helpful and important tool for noise management and acoustical planning in urban areas. However, the static noise map is not sufficient for evaluating noise annoyance at different temporal periods. It is necessary to develop the dynamic noise map or the noise spatiotemporal distribution. In this study, a method about urban road traffic noise spatiotemporal distribution mapping is proposed to obtain the representative road traffic noise maps of different periods. This method relies on the proposed noise spatiotemporal distribution model with two time-dependent variables - traffic density and traffic speed, and the spatiotemporal characteristics derived from multisource data. There are three steps in the method. First, the urban road traffic noise spatiotemporal distribution model is derived from the law of sound propagation. Then, the temporal characteristics are extracted from traffic flow detecting data and E-map road segment speed data by the outlier detection analysis. Finally, the noise distributions corresponding to different periods are calculated by an efficient algorithm which can save 90% above of the computing time. Moreover, a validation experiment was conducted to evaluate the accuracy of the proposed method. There is only 2.26-dB[A] mean absolute error that is within an acceptable range, which shows that the method is effective.     

Towards a real-time microscopic emissions model

This article presents a new approach to microscopic road traffic exhaust emission modelling. The model described uses data from the SCOOT demand-responsive traffic control system implemented in over 170 cities across the world. Estimates of vehicle speed and classification are made using data from inductive detector loops located on every SCOOT link. This data feeds into a microscopic traffic model to enable enhanced modelling of the driving modes of vehicles (acceleration, deceleration, idling and cruising). Estimates of carbon monoxide emissions are made by applying emission factors from an extensive literature review. A critical appraisal of the development and validation of the model is given before the model is applied to a study of the impact of high emitting vehicles. The article concludes with a discussion of the requirements for the future development and benefits of the application of such a model.     

Accounting for traffic speed dynamics when calculating COPERT and PHEM pollutant emissions at the urban scale

Coupling a traffic microsimulation with an emission model is a means of assessing fuel consumptions and pollutant emissions at the urban scale. Dealing with congested states requires the efficient capture of traffic dynamics and their conditioning for the emission model. Two emission models are investigated here: COPERT IV and PHEM v11. Emission calculations were performed at road segments over 6 min periods for an area of Paris covering 3 km². The resulting network fuel consumption (FC) and nitrogen oxide (NOx) emissions are then compared. This article investigates: (i) the sensitivity of COPERT to the mean speed definition, and (ii) how COPERT emission functions can be adapted to cope with vehicle dynamics related to congestion. In addition, emissions are evaluated using detailed traffic output (vehicle trajectories) paired with the instantaneous emission model, PHEM.COPERT emissions are very sensitive to mean speed definition. Using a degraded speed definition leads to an underestimation ranging from −13% to −25% for fuel consumption during congested periods (from −17% to −36% respectively for NOx emissions). Including speed distribution with COPERT leads to higher emissions, especially under congested conditions (+13% for FC and +16% for NOx). Finally, both these implementations are compared to the instantaneous modeling chain results. Performance indicators are introduced to quantify the sensitivity of the coupling to traffic dynamics. Using speed distributions, performance indicators are more or less doubled compared to traditional implementation, but remain lower than when relying on trajectories paired with the PHEM emission model.     

Modelling acceleration decisions in traffic streams with weak lane discipline: A latent leader approach

Acceleration is an important driving manoeuvre that has been modelled for decades as a critical element of the microscopic traffic simulation tools. The state-of-the art acceleration models have however primarily focused on lane based traffic. In lane based traffic, every driver has a single distinct lead vehicle in the front and the acceleration of the driver is typically modelled as a function of the relative speed, position and/or type of the corresponding leader. On the contrary, in a traffic stream with weak lane discipline, the subject driver may have multiple vehicles in the front. The subject driver is therefore subjected to multiple sources of stimulus for acceleration and reacts to the stimulus from the governing leader. However, only the applied accelerations are observed in the trajectory data, and the governing leader is unobserved or latent. The state-of-the-art models therefore cannot be directly applied to traffic streams with weak lane discipline.This prompts the current research where we present a latent leader acceleration model. The model has two components: a random utility based dynamic class membership model (latent leader component) and a class-specific acceleration model (acceleration component). The parameters of the model have been calibrated using detailed trajectory data collected from Dhaka, Bangladesh. Results indicate that the probability of a given front vehicle of being the governing leader can depend on the type of the lead vehicle and the extent of lateral overlap with the subject driver. The estimation results are compared against a simpler acceleration model (where the leader is determined deterministically) and a significant improvement in the goodness-of-fit is observed. The proposed models, when implemented in microscopic traffic simulation tools, are expected to result more realistic representation of traffic streams with weak lane discipline.     

Instantaneous emissions models set in GIS for the TRANSIMS outputs

A novel methodology that provides more detailed estimates of vehicular polluting emissions is offered, in order to contribute to the improvement and the precision of emission inventories of vehicle sources through the consideration of instantaneous speed changes or acceleration instead of average vehicular speeds. This paper presents the construction and application of an instantaneous emissions model designated hereunder as “Transims’s Snapshots-Based Emissions”, which is set on a Geographic Information System that incorporates instantaneous fuel consumption factors and fuel-based emission factors to attain highest resolution of both, spatial and temporal distribution of vehicular polluting emissions based on traffic simulation through cellular automata with TRANSIMS. This work was applied to the road network of the Mexico City Metropolitan Area as case study. The development of this powerful tool led to obtaining 86,400 maps of the spatial and temporal distribution of vehicular emissions per vehicle circulating on the road network, including the following pollutants: carbon monoxide and carbon dioxide, nitrogen oxides, total hydrocarbons, sulfur oxides, polycyclic aromatic hydrocarbons, black carbon, particles PM₁₀ and PM_2.5. The said maps allowed identification with highest level of detail, of the emissions and Hot-spots of fuel consumption. Also, the model permitted to obtain the emissions’ longitudinal profiles of a given vehicle along its route. This study shows that the integration method of the polynomial regression models represents an opportunity for each city to develop more easily and openly its own regional emissions models without requiring deeper programming knowledge.     

Spatiotemporal intersection control in a connected and automated vehicle environment

Current research on traffic control has focused on the optimization of either traffic signals or vehicle trajectories. With the rapid development of connected and automated vehicle (CAV) technologies, vehicles equipped with dedicated short-range communications (DSRC) can communicate not only with other CAVs but also with infrastructure. Joint control of vehicle trajectories and traffic signals becomes feasible and may achieve greater benefits regarding system efficiency and environmental sustainability. Traffic control framework is expected to be extended from one dimension (either spatial or temporal) to two dimensions (spatiotemporal). This paper investigates a joint control framework for isolated intersections. The control framework is modeled as a two-stage optimization problem with signal optimization at the first stage and vehicle trajectory control at the second stage. The signal optimization is modeled as a dynamic programming (DP) problem with the objective to minimize vehicle delay. Optimal control theory is applied to the vehicle trajectory control problem with the objective to minimize fuel consumption and emissions. A simplified objective function is adopted to get analytical solutions to the optimal control problem so that the two-stage model is solved efficiently. Simulation results show that the proposed joint control framework is able to reduce both vehicle delay and emissions under a variety of demand levels compared to fixed-time and adaptive signal control when vehicle trajectories are not optimized. The reduced vehicle delay and CO₂ emissions can be as much as 24.0% and 13.8%, respectively for a simple two-phase intersection. Sensitivity analysis suggests that maximum acceleration and deceleration rates have a significant impact on the performance regarding both vehicle delay and emission reduction. Further extension to a full eight-phase intersection shows a similar pattern of delay and emission reduction by the joint control framework.     

Spin glass and the interactions of congestion and emissions: An exploratory step

This paper models traffic congestion formation on highways and roads by recognizing the centrality of dynamical systems and using concepts from complexity theory as imbedded in the spin glasses analogue. Further, it explores the concept of how an increase in air pollution caused by vehicle exhaust emission can be traced to traffic congestion, specifically to the acceleration/deceleration of vehicles on the roads. First, spin glass is introduced and then by applying the two-dimensional x − y Ising model and defining a Hamiltonian (based on Edwards-Anderson and Mattis models of spin glass systems) for a system of vehicles on the road, derivations are made of the specific friction of congestion and the bulk modulus of congestion using the Gibbs-Boltzmann statistic. Similarly using the interactions of vehicles with each other and the resulting accelerations and decelerations of vehicles as the basis for exhaust emissions, derivations are made of a specificity of exhaust emissions. These are analogues to the entropy models of thermodynamics. This series of derivations serves as an analytical model for detecting incidents of congestion and increase in air pollution due to exhaust emissions in transportation systems.     

Modeling the effect of electric vehicle adoption on pedestrian traffic safety: An agent-based approach

When operated at low speeds, electric and hybrid vehicles have created pedestrian safety concerns in congested areas of various city centers, because these vehicles have relatively silent engines compared to those of internal combustion engine vehicles, resulting in safety issues for pedestrians and cyclists due to the lack of engine noise to warn them of an oncoming electric or hybrid vehicle. However, the driver behavior characteristics have also been considered in many studies, and the high end-prices of electric vehicles indicate that electric vehicle drivers tend to have a higher prosperity index and are more likely to receive a better education, making them more alert while driving and more likely to obey traffic rules. In this paper, the positive and negative factors associated with electric vehicle adoption and the subsequent effects on pedestrian traffic safety are investigated using an agent-based modeling approach, in which a traffic micro-simulation of a real intersection is simulated in 3D using AnyLogic software. First, the interacting agents and dynamic parameters are defined in the agent-based model. Next, a 3D intersection environment is created to integrate the agent-based model into a visual simulation, where the simulation records the number of near-crashes occurring in certain pedestrian crossings throughout the virtual time duration of a year. A sensitivity analysis is also carried out with 9000 subsequent simulations performed in a supercomputer to account for the variation in dynamic parameters (ambient sound level, vehicle sound level, and ambient illumination). According to the analysis, electric vehicles have a 30% higher pedestrian traffic safety risk than internal combustion engine vehicles under high ambient sound levels. At low ambient sound levels, however, electric vehicles have only a 10% higher safety risk for pedestrians. Low levels of ambient illumination also increase the number of pedestrians involved in near-crashes for both electric vehicles and combustion engine vehicles.