共查询到19条相似文献,搜索用时 390 毫秒
1.
2.
3.
散货船和油船协调后的共同结构规范(HSR)将于2011年生效。为促进规范的发展,使之符合IMO目标型船舶标准(GBS)的要求,从整体舱段有限元分析、详细应力评估和疲劳强度评估的热点应力分析3个方面阐述了散货船共同结构规范的不足之处,并提出了相应的建议。 相似文献
4.
5.
基于目标型标准的油船和散货船协调共同规范HCSR(Harmonised Common Structural Rules)即将于2014年12月实行,其最大特色就是协调统一了散货船及油船这两种船型的一些规范条款。本文主要论述了在疲劳强度校核问题上,相对于散货船结构共同规范CSR-BC(Common Structural Rules for Bulk Carriers),HCSR在载荷工况,疲劳寿命评估方法,典型热点分析方法,有限元热点插值方法,S-N曲线选取等方面的改进。 相似文献
6.
散货船和油船协调版共同结构规范于2015年7月1日正式生效。按照IMO GBS的要求,该规范的框架体系和规范要求在散货船共同结构规范和油船共同结构规范的基础上作出较大改变。文章对该规范的编制原理进行剖析,对理解和掌握规范的编写思路及规范要求的技术背景具有指导意义。 相似文献
7.
8.
9.
10.
11.
面对当前城际铁路建设项目分析客运量准确、高效的要求,系统介绍了手机移动话单数据的内容,分析了将其应用在客运量分析方面与传统铁路客流量预测方法相比的优势。研究了将移动话单数据应用于城际铁路客流量分析工作的实施步骤以及具体方法与模型。总结了国内外目前利用手机话单数据进行交通调查的研究现状,以及目前对这种技术实施大规模应用的瓶颈。研究表明,利用手机移动话单数据分析城际铁路客运量的思路可行,实施过程中不再需要高成本的 OD 调查数据支撑,有着广阔的应用前景。 相似文献
12.
肘板趾端是船舶与海洋结构的疲劳热点。文章用三维有限元分析了趾端表面裂纹应力强度因子修正系数的变化规律,并与BS7910推荐的典型节点表面裂纹应力强度因子公式计算结果作了对比,结果表明趾端表面裂纹应力强度因子沿深度方向的放大系数和T型节点相差很小,而表面端点应力强度因子修正系数则当裂纹长度在肘板厚度范围内时和T型节点相差很小,超出后则相差较大。以某客滚船上肘板趾端应力范围长期分布服从Weibull分布,产生系列均值为零的应力幅,应力强度因子分别采用有限元结果和BS7910中T型接头公式进行计算,采用单一曲线模型计算该趾端表面裂纹的裂纹扩展。计算等效应力强度因子幅时,考虑焊接残余应力的影响。计算结果表明以T型接头的公式计算趾端表面裂纹应力强度因子和有限元结果相差很小。建议将T型节点表面裂纹应力强度因子计算公式用于趾端表面裂纹应力强度因子的计算,并采用单一曲线模型对随机波浪载荷下作用下船舶典型节点疲劳裂纹的扩展寿命进行了预报。 相似文献
13.
船舶的大型化和标准化可有效提高航道和通航设施的利用率和通过能力。引入单吨面积综合反映内河船舶的吨位和平面尺度,采用船舶尺度标准化系数衡量船舶尺度的标准化程度,可将它们作为反映船舶大型化和标准化的衡量指标之一。 相似文献
14.
15.
T型接头焊趾表面裂纹应力强度因子的简化计算方法 总被引:5,自引:0,他引:5
T型接头是船舶与海洋结构物的典型结构形式之一,其焊趾处常常是疲劳热点区域。T型接头焊趾表面裂纹的应力强度因子是船舶与海洋结构的、基于断裂力学安全评定和疲劳寿命预测的基础。本文对T型接头表面裂纹应力强度因子的计算方法,尤其是Bow ness等人提出的T型接头焊趾表面裂纹应力强度因子的计算公式进行了分析,在此基础上导出了形式简单,物理意义明确的T型接头焊趾表面裂纹应力强度因子的简化计算公式,并和相关的应力强度因子的计算结果进行了比较,证明了本文简化方法的可行性。 相似文献
16.
Sara Y. Kenno Sreekanta Das John B. Kennedy Ronald B. Rogge Michael Gharghouri 《Marine Structures》2010,23(3):263-273
This paper provides an in-depth study of residual stress distributions found in stiffened steel plate structures, such as those typically used in ship hulls. The effect of stiffener spacing on the distribution of residual stress components was studied. The welding heat input was also varied between high and moderate to study the effect of heat input level on residual stress distributions. Four specimens, resembling typical stiffened steel plate structures used in ship hulls were built and tested. Steel plates of 9.5 mm thickness were stiffened by welding L127 × 76 × 9.5 steel angles. The test was completed using the neutron diffraction method. The three normal components of residual stress were obtained in this study. It was found that a lower heat input results in higher tensile residual stress and that there exists a critical stiffener spacing somewhere beyond 250 mm that creates a maximum tensile residual stress value near the welded connection. 相似文献
17.
通过一种有效的构建三维M/S/Cu配位聚合物的方法,成功合成了一个新的基于鞍状单体[ MoS4 Cu4]的阴阳离子穿插的三维配位聚合物{[MoS4Cu4(4,4′-bpy)4][MoS4Cu4(4,4′-bpy)2I4·4H2O]}n.X射线单晶衍射表明,该晶体属于四方晶系,空间群为I41/acd,a=24.830(3)?,b=24.830(3)?,c=28.208(6)?,α=β=γ=90°.晶体结构分析显示,配位聚合物1由穿插的阳离子[MoS4Cu4(4,4′-bpy)4]2+和阴离子[MoS4Cu4(4,4′-bpy)2I4·4H2O]2-组成的三维钻石状配位聚合物. 相似文献
18.
Compared with thick plate welded joint, the welding joint of thin plate will produce initial deformation due to its low bending rigidity. The existence of initial deformation will cause the welded structure to produce secondary bending effect, which will produce greater stress magnification effect at the weld toe and seriously affect the fatigue strength of thin plate welded joints. Therefore, based on the correction formula of thick plate, considering the influence of initial deformation and geometric nonlinearity of thin plate, this paper deduces the stress magnification factor formula at the weld toe of T-shaped and cruciform specimens. The accuracy of the revised formula is further verified by comparing the notch stress calculated by the modified formula with the FE results. Finally, the modified formula is applied to the notch stress and fatigue evaluation of typical thin plate welded joints respectively. The results show that the proposed notch stress calculation formula can fully consider the stress amplification effect of thin plate structure, and can be used to quickly evaluate the notch stress field and fatigue strength of thin plate welded joints. 相似文献