Energy use and emissions of two stroke-powered tricycles in Metro Manila

CO, CO₂, NO_x and HC emissions of two stroke-powered tricycles in Metro Manila are examined using an instantaneous emissions model. Results show that fuel consumption and HC emissions in middle class residential areas and main roads are similar but lower than levels in low income residential areas. On the average, tricycles in Metro Manila consume 24.41 km/l of fuel and produces 9.5, 9.7, 40.5 and 0.07 g/km of HC, CO, CO₂ and NO_x, respectively. They fail to satisfy HC, CO and NO_x emission limits set by reference standards in the Philippines and other Asian countries. They produce greater HC and CO emissions than gasoline fueled private cars and diesel powered public jeepneys, taxis and buses on a per passenger-km basis but significantly lower NO_x emissions. Tricycles account for 15.4% of the total HC emissions from mobile sources in the metropolis while their contributions to CO, CO₂ and NO_x are minimal.     

Exhaust emissions generated under actual operating conditions from a hybrid vehicle and an electric one fitted with a range extender

The paper describes exhaust emission tests performed on a PHEV (Plug-in Hybrid Electric Vehicle) and a BEV (Battery Electric Vehicle), in which the combustion engine was used as a range extender. The measurements of the exhaust emissions were performed for CO₂/fuel consumption, CO, THC and NO_x. The RDE measurements were performed including the engine operating parameters and emissions analysis. This analysis shows that the engines of BEVs and PHEVs operate in a different parameter range when under actual operating conditions, which directly translates into the exhaust emission values. This is particularly the case for the emission of NO_x. The investigations were carried out for two routes differentiated by the length and share of the urban and extra-urban cycles. For both routes, the emission of THC and CO were lower for the PHEV engine – HC by 69% (22 mg/km, route 1) and 6% (15 mg/km, route 2), CO by 69% (0.12 mg/km, route 1) and 80% (0.1 mg/km, route 2). For route 1, characterized by a greater share of the urban cycle, the emission of NO_x was lower by 70% (2 mg/km) for the BEV engine, and (route 2) lower by 60% (8 mg/km) for the PHEV engine. Additionally, the curves of the exhaust emissions in time for individual exhaust components have been presented that indicate that in the motorway cycle the emission of THC and CO from the BEV vehicle increases significantly up to ten times compared to urban cycle.     

Mitigating air pollution impacts of passenger ferries

Increasing regional mobility demand amid rising roadway congestion has motivated plans for passenger ferry expansion and modernization in many parts of the US. While this trend applies to ferry systems in Alaska, New York, Boston, and Washington state, efforts to expand ferry service in the San Francisco Bay Area are unique in scale and vision. Integrating ferry service into the regional, door-to-door transit system can significantly increase water-crossing capacity for commuters. However, to realize this potential, the ferry industry must meet several challenges associated with growth, including environmental impacts. In particular, concern over air pollution emissions from marine engines is motivating new comparisons between ferries and other transportation modes in terms of both mobility and air pollution. This paper describes the current debate about ferry system operation and expansion, and presents a parametric analysis comparing existing, uncontrolled ferry emissions to automobiles. Under all reasonable assumptions, we show that diesel-powered ferries without emissions controls will produce more NO_x and PM, but less CO per passenger-trip than if those people commuted by car under current conditions. This paper also projects the emissions from the expanded ferry system proposed for the San Francisco Bay Area, showing that a larger ferry fleet equipped with new engines meeting future EPA emissions standards could become one of the major non-road NO_x sources in the region. We conclude by outlining the alternatives and challenges to reduce ferry emissions so that they are more comparable to automobile emissions. Policy implications of these alternatives are also discussed.     

Correcting injection pressure maladjustments to reduce NOX emissions by marine diesel engines

Emissions from the exhausts of marine diesel engines comprises several different gases including NO_X. These are currently regulated at the international level under Regulation 13 of ANNEX VI of MARPOL 73/78, but this regulation only applies to new engines and is based on bench tests, for only a single engine designated the “parent engine”. Here, the need to take measurements from across their whole range and once in operation on board a vessel is examined. This would not only improve assessment of new equipment against the current regulation, but would also detect defects in the functioning of the engine.     

Comparing air pollution from ferry and landside commuting

Recent and anticipated growth in passenger ferry service has been complicated by concerns about air pollution from marine engines that are only starting to be regulated. While marine engines are known to be a significant and growing source category in some locations, sparse data and analytical difficulties have prevented rigorous comparisons of marine and on-land passenger travel. Using data gathered in the San Francisco Bay Area, we model emissions from three passenger ferries and the matching on-land travel that would be used by commuters if ferry service were not available. The results are analyzed parametrically for levels of ridership and induced travel demand, and for new technologies, including selective catalytic reduction and natural gas fuel. Results indicate that under some conditions, passenger ferries reduce some emissions (including particulate matter emissions) relative to the matching on-land service but increase others. Emissions of NO_X are particularly problematic––all the technologies examined lead to increased NO_X emissions due to ferry commuting. Some of the emissions comparisons are sensitive to mode split, ridership, or induced travel demand. However, NO_X emissions are not––ferry commuting always raises NO_X emissions, even with the most advanced technologies. Implications for local air quality regulators and for technology development are discussed.     

System for assessing Aviation’s Global Emissions (SAGE), Part 1: Model description and inventory results

In early 2001, the US Federal Aviation Administration embarked on a multi-year effort to develop a new computer model, the System for assessing Aviation’s Global Emissions (SAGE). Currently at Version 1.5, the basic use of the model has centered on the development of yearly global inventories of commercial aircraft fuel burn and emissions of various pollutants to serve as the basis for scenario modeling. This paper describes the algorithms and data used in the model as well as the results from initial validation assessments. SAGE results indicate that global fuel burn and nitrogen oxide (NO_x) emissions decreased by over 6% from 2000 to 2001 (fuel burn and NO_x), and then steadily increased to over 12% (fuel burn) and 15.5% (NO_x) above 2000 levels in 2005. Comparisons to the results from previous studies have shown that SAGE tends to agree more closely with fuel burn and NO_x than with CO and HC. Validation assessments have shown that SAGE can predict per flight fuel burn to within 3% on an average basis with no apparent bias, when compared to about 60,000 flight’s worth of data from a major US airline and about 20,000 flight’s worth of data from two major Japanese airlines.     

The effects of small roundabouts on emissions and fuel consumption: a case study

The effects of small roundabouts on emissions and fuel consumption were evaluated using the “car-following” method in a before/after study. The results showed that at a roundabout replacing a signalised junction, CO emissions decreased by 29%, NO_x emissions by 21% and fuel consumption by 28%. At roundabouts, replacing yield regulated junctions, CO emissions increased on average by 4%, NO_x emissions by 6% and fuel consumption by 3%. The results indicate that the large reductions in emissions and fuel consumption at one rebuilt signalised junction can “compensate for” the increase produced by several yield-regulated junctions rebuilt as roundabouts.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Exhaust emissions and fuel consumption of a triple-fuel spark-ignition engine powered passenger car

This paper examines the influence of compressed natural gas, liquefied petroleum gas and gasoline fuel on the exhaust emissions and the fuel consumption of a spark-ignition engine powered passenger car. The vehicle was driven according to the urban driving cycle and extra urban driving cycle speed profiles with the warmed-up engine. Cause and effect based analysis reveals potential for using different fuels to reduce vehicle emission and deficiencies associated with particular fuels. The highest tank to wheel efficiency and the lowest CO₂ emission are observed with the natural gas fuelled vehicle, that also featured the highest total hydrocarbon emissions and high NO_x emissions because of fast three way catalytic converter aging due the use of the compressed natural gas. Retrofitted liquefied petroleum gas fuel supply systems feature the greatest air-fuel ratio variations that result in the lowest TtW efficiency and in the highest NO_x emissions of the liquefied gas fuelled vehicle.     

Real-world gaseous and particle emissions of a Bi-fuel gasoline/CNG Euro 6 passenger car

The objective of the present study is the assessment of the environmental impact of a bivalent (bi-fuel) vehicle, running either on gasoline or compressed natural gas (CNG). To that aim, a Euro 6 passenger car was tested under various real-world driving conditions. In order to cover the full range of conventional powertrains currently in the market, the tests were also repeated on a Euro 6 diesel passenger car. Both cars were driven in two routes, the first complying with the regulation limits and the second going beyond them. Carbon monoxide (CO), nitrogen oxides (NO_x) and particle number (PN) emissions were recorded using a Portable Emissions Measurement System (PEMS). Apart from the aggregated emission levels, in g/km, the exact emission location along the route was also assessed. Natural gas proved beneficial for CO and PN emissions, the level of which always remained below the respective legislation limits. On the other hand, under the dynamic driving conditions with gasoline, the relevant limits were exceeded. Cold start, occurring at the beginning of the urban part, and motorway driving were identified as major contributors to total emissions, especially in gasoline mode. However, the application of natural gas was associated with a penalty in NO_x emissions, which were significantly increased as compared to gasoline. Local peaks within the urban part were identified in CNG mode. In any case, the diesel vehicle was by far the highest NO_x emitter.     

Thermodynamic,environmental and economic analysis of absorption air conditioning unit for emissions reduction onboard passenger ships

In this paper, the waste heat of exhaust gases and jacket cooling water in marine diesel engines are analyzed to operate the absorption refrigeration unit (ARU). Thermo-economic and environmental analysis of the absorption refrigeration cycle operated with the two heat sources that use lithium bromide as an absorbent is carried out. The analysis is performed using Engineering Equation Solver (EES) software package where the thermodynamic properties of the steam and the LiBr-water mixtures are provided. The used EES code is verified by published experimental data. As a case study, high speed passenger vessel operating in the Red Sea area has been investigated. The results show that a considerable specific economic benefit could be achieved from ARU jacket cooling water operated over that gained from main engine exhaust gases. Environmentally, applying ARU machine during cruise will reduce the annual fuel consumption for the diesel generators by 156 ton with a reduction percentage of 23%. This will reduce the exhaust gas emissions by 6.3% from the applied main engine emissions. In addition, this will result in reducing NO_x, SO_x, and CO₂ emissions with cost-effectiveness of 4.99 $/kg, 13.18 $/kg, and 0.08 $/kg, respectively.     

A velocity and payload dependent emission model for heavy-duty road freight transportation

The paper develops a forecasting model of emissions from traffic flows embracing the dynamics of driving behavior due to variations in payload. To measure of emissions at the level of individual vehicles under varying payloads a portable emission measurement system is used. This paper reports on a model based on data at the level of individual vehicles for a representative road trajectory. The model aggregates the data to the level of a homogeneous flow dependent of velocity and specific power, which is dependent on payload weight. We find a lean specification for the model that provides emission factors for CO₂, NO_x, HC, CO, and NO₂. The results indicate that, in comparison with earlier models, NO_x emissions in particular tend to be underestimated.     

System for assessing Aviation’s Global Emissions (SAGE), Part 2: Uncertainty assessment

This paper focuses on assessing and applying the Federal Aviation Administration’s System for assessing Aviation’s Global Emissions (SAGE), Version 1.5, to evaluate global aircraft fuel consumption and emissions. The model is capable of computing fuel burn and emissions on a flight-by-flight, fleet and global basis. Here, a parametric study was conducted to rank-order the effects that the modeling uncertainties had on estimates of fuel burn and emissions. Statistical methods were applied to analyze both the random and systematic errors of the model. Also, applying the model to a sample policy analysis case allowed an examination of more stringent engine certification standards for mitigating aviation emissions. Uncertainties of the model were carefully accounted for in the fuel burn and emissions scenarios of the policy options. Results show that for some applications, SAGE may be used to resolve small differences in fleet emissions performance. Although the absolute uncertainty in flight-by-flight NO_x predictions from the model are of the order of 40%, results show that it is well within the current capabilities of the model to distinguish between the fleet average NO_x emissions associated with the typical NO_x stringency options considered in policy analyses.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

A statistical model for estimating oxides of nitrogen emissions from light duty motor vehicles

Motor vehicle emission rate models for predicting oxides of nitrogen (NOx) emissions are insensitive to vehicle modes of operation such as cruise, acceleration, deceleration, and idle, because they are based on average trip speed. Research has shown that NOx emissions are sensitive to engine load; hence, load-based variables need to be included in emissions models. Ongoing studies attempting to incorporate these `modal' variables have experienced difficulties with: (1) incomplete and/or non-representative data sets of emissions test data vis-a-vis the modal operating profiles of the tested vehicles; (2) lack of information for predicting on-road operating parameters of vehicles; and (3) non-representative vehicles recruited for emissions tests.The objective of this research was to develop a statistical model for predicting NOx emissions from light-duty gasoline motor vehicles. The primary end use of this model is forecasting, rather than explanation of the factors that affect NOx emissions, which brings to bear different requirements from the statistical model. The three challenges noted above are addressed by: (1) analyzing a data set of more than 13 000 hot-stabilized laboratory treadmill tests on 19 driving cycles (specific speed versus time testing conditions), and 114 variables describing vehicle, engine and test cycle characteristics; (2) making the models compatible with empirical data on how vehicles are being operated in-use; and (3) developing statistical weights to account for the differences in model year distributions between the emissions testing database and the current national on-road fleets.The NOx emissions model is estimated using ordinary least-squares regression techniques, with transformed response variable and regression weights. Tree regression is employed as a tool for mining relationships among variables in the data, with particular focus on identifying useful interactions among discrete variables. Details of the model development process are presented, as well as results for the final model showing the predicted emissions algorithm for the current motor vehicle fleet in Atlanta, GA metropolitan region.     

Individual exposure to traffic related air pollution across land-use clusters

In this study, we estimated the transportation-related emissions of nitrogen oxides (NO_x) at an individual level for a sample of the Montreal population. Using linear regression, we quantified the associations between NO_x emissions and selected individual attributes. We then investigated the relationship between individual emissions of NO_x and exposure to nitrogen dioxide (NO₂) concentrations derived from a land-use regression model. Factor analysis and clustering of land-uses were used to test the relationships between emissions and exposures in different Montreal areas. We observed that the emissions generated per individual are positively associated with vehicle ownership, gender, and employment status. We also noted that individuals who live in the suburbs or in peripheral areas generate higher emissions of NO_x but are exposed to lower NO₂ concentrations at home and throughout their daily activities. Finally, we observed that for most individuals, NO₂ exposures based on daily activity locations were often slightly more elevated than NO₂ concentrations at the home location. We estimated that between 20% and 45% of individuals experience a daily exposure that is largely different from the concentration at their home location. Our findings are relevant to the evaluation of equity in the generation of transport emissions and exposure to traffic-related air pollution. We also shed light on the effect of accounting for daily activities when estimating air pollution exposure.     

PM2.5 and NOx from traffic: Human health impacts,external costs and policy implications from the Belgian perspective

This article employs an optimized impact pathway approach to marginal external health costs that relies on high-resolution dispersion models calibrated for Belgium and the surrounding areas. Per tonne, the MEHC_PM2.5 is found to be many times larger than MEHC_NOx, which is currently negative. Further, the impact of Belgian PM_2.5 emissions in the immediate area of generation is significantly larger than the impact on more distant areas; the opposite is true for NO_x. The MEHCs of both pollutants are predicted to increase in the coming years. Further analysis of the impacts of PM_2.5 and NO_x reveals that, on average, modern gasoline vehicles outperform their diesel counterparts as far as future emissions are concerned. This contrasts with findings for 2007, which suggested that Euro 5 diesels had fewer associated health costs because of the potential for ozone reduction offered by their NO_x emissions.     

Real-world gaseous emission characteristics of Euro 6b light-duty gasoline- and diesel-fueled vehicles

To accurately investigate vehicle emissions that have become major contributors to global air pollutants and greenhouse gases, test conditions have been transferred from laboratory type approval test cycles to real-world driving conditions. In this study, the real-world driving emissions of carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NO_x), and carbon dioxide (CO₂) from one gasoline and two diesel Euro 6b light-duty passenger vehicles were investigated by a portable emission measurement system (PEMS) in Lyon, France. NO_x and CO₂ emission controls remain critical to addressing the real-world driving emissions of Euro 6b vehicles. Notably, the tested gasoline vehicle emitted higher CO₂ emissions than diesel vehicles on all types of roads, especially on the urban road with an excess of 29.3–48.3%. The highest emission factors of gaseous pollutants generally occurred on the motorway for the gasoline vehicle, while on the urban road for diesel vehicles. In particular, for high-speed driving conditions, the gasoline vehicle gaseous emissions, especially NO_x emissions, were more affected by acceleration than diesel vehicle emissions. In addition, the CO emissions, especially THC emissions, for the gasoline vehicle, were more influenced by warm-start, especially cold-start, than those for diesel vehicles.     

Potential of low viscosity oils to reduce CO2 emissions and fuel consumption of urban buses fleets

This paper shows the results of a comparative fleet test the main objective of which was to measure the influence of Low Viscosity Oils (LVO) over the fuel consumption and CO₂ emissions of urban buses. To perform this test, 39 urban buses, classified into candidate and reference groups depending on the engine oil viscosity, covered a 60,000 km mileage corresponding to two rounds of standard Oil Drain Interval (ODI). In the same way, for 9 buses of the 39 buses, the effect of differential LVO over fuel consumption and their interaction with engine LVO was assessed during the second ODI.Test results confirm that the use of LVO could reduce fuel consumption, hence CO₂ emissions. However, special attention should be taken prior to its implementation in a fleet, particularly if the vehicles are powered by engines with high mechanical and thermal stresses during vehicle operation because this could lead to friction loss increase, loss of the potential fuel consumption reduction of LVO and, in the worst scenario, higher rates of engine wear.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.