The Influence of Tire Factors on the Stability of Trucks and Tractor Trailers

The mechanical properties of tires and trucks are contrasted with comparable properties of the motor car to explain why the motor truck and the tractor-trailer can exhibit fixed-control instability at moderate levels of lateral acceleration. The (1) rearward bias in the distribution of roll stiffness, (2) large ratio of e.g. height to track, and (3) low torsional stiffness of the parallel-rail frame (as typically employed in heavy commercial vehicles) are found to be the major factors implicated in this phenomenon. Experimental and analytical evidence is provided to show how tire inflation pressure and mixes of (a) tire-carcass construction and (b) tread design also influence stability at moderate levels of lateral acceleration. Conclusions relating to the safety of commercial vehicle operations are drawn.     

The Influence of Structural Flexibilities on the Straight-running Stability of Motorcycles

SUMMARY

A new tyre model for studies of motorcycle lateral dynamics, and three new motorcycle models, each incorporating a different form of structural compliance, are developed. The tyre model is based on “taut string” ideas, and includes consideration of tread width and longitudinal tread rubber distortion and tread mass effects, and normal load variation. Parameter values appropriate to a typical motorcycle tyre are employed. The motorcycle models are for small lateral perturbations from straight running at constant speed, and include (a) lateral compliance of the front wheel in the front forks, (b) torsional compliance of the front forks, and (c) torsional compliance in the rear frame at the steering head about an axis perpendicular to the steering axis.

Results in the form of eigenvalues, indicating modal damping properties and natural frequencies are presented for each model. The properties of four large production machines for a range of forward speeds, and the practicable range of stiffnesses are calculated, and the implications are discussed.

It is concluded that typical levels of structural compliance in models (a) and (c) contribute significantly to the steering behaviour properties of large motorcycles, and their observed behaviour can be understood better in terms of the new results than of those existing previously. Some conclusions relating to optimal structural stiffness properties are also drawn.     

High Speed Stability for Rail Vehicles Considering Varying Conicity and Creep Coefficients

SUMMARY

The critical or hunting speed of solid axle rail vehicles is known to be a strong function of primary suspension stiffness, wheel/rail profile geometry (conicity and gravitational stiffness), wheel/rail friction forces (creep coefficients), bogie/carbody inertia properties, and secondary suspension design. This paper deals with the problem of maximizing the critical speed through design of the primary and secondary suspension but with control only over the range of wheel/rail geometry and friction characteristics. For example, the conicity may varie from .05 to .3 and the linear creep coefficients from 25% to 100% of the predicted Kalker values.

It is shown that the maximum critical speed is greatly limited by the wheel/rail geometry and friction variations. It is also shown that, when lateral curving and ride quality are considered, the best design approach is to select an intermediate primary longitudinal stiffness, to limit the lowest value of conicity (e.g. to .1 or .2) by wheel profile redesign, increasing the secondary yaw damping value (yaw relaxation) and optimizing the primary and secondary lateral stiffness.     

Roll Plane Analysis of Articulated Tank Vehicles During Steady Turning

SUMMARY

The rollover immunity levels of articulated tank vehicles with partial loads are investigated. A static roll plane model of the articulated vehicle employing partially filled cylindrical tank is developed. The vertical and lateral translation of the liquid cargo due to vehicle roll angle and lateral acceleration, encountered during steady turning, are evaluated. The roll moments arising from vertical and lateral translation of the liquid cargo are determined and incorporated in the roll plane model of the vehicle. The adverse influence of the unique interactions of the liquid within the tank vehicle, on the rollover limit of the articulated vehicle is demonstrated. The influence of compartmenting of the tank on the steady turning roll response of the vehicle is analyzed, and an optimal order of unloading the compartmented tank is discussed.     

Control of semi-active anti-roll systems on heavy vehicles

Semi-active anti-roll systems, with a high and low roll stiffness, or, since cornering is typically a transient event, damping setting have the capacity to improve heavy vehicle stability while having very low power consumption. If a vehicle is travelling around a right-hand bend and a low roll damping setting is selected, the vehicle will roll outwards. If a high damping setting is then selected, the outward roll will be locked-in. When the vehicle enters a left-hand bend, the inward roll becomes locked-in. This has the potential to increase critical lateral acceleration by up to 12.5% if the vehicle's future course can be predicted accurately (e.g. with a Global Positioning System). However, if the vehicle does not follow the expected path, the critical lateral acceleration may be degraded. Exploiting the delay between a steer angle being applied and the lateral acceleration developing could avoid this problem. However, the benefits from such a system are considerably lower, up to a 2.4% improvement in critical lateral acceleration. Hence, a ‘modal control strategy’ is developed aimed at providing high levels of benefit while being robust to deviations from the expected path. The modal strategy is able to provide benefits of up to 11%, while being robust to most deviations.     

Optimal control of brakes and steering for autonomous collision avoidance using modified Hamiltonian algorithm

ABSTRACT

This paper considers the problem of collision avoidance for road vehicles, operating at the limits of friction. A two-level modelling and control methodology is proposed, with the upper level using a friction-limited particle model for motion planning, and the lower level using a nonlinear 3DOF model for optimal control allocation. Motion planning adopts a two-phase approach: the first phase is to avoid the obstacle, the second is to recover lane keeping with minimal additional lateral deviation. This methodology differs from the more standard approach of path-planning/path-following, as there is no explicit path reference used; the control reference is a target acceleration vector which simultaneously induces changes in direction and speed. The lower level control distributes vehicle targets to the brake and steer actuators via a new and efficient method, the Modified Hamiltonian Algorithm (MHA). MHA balances CG acceleration targets with yaw moment tracking to preserve lateral stability. A nonlinear 7DOF two-track vehicle model confirms the overall validity of this novel methodology for collision avoidance.     

Lateral Dynamics of Commercial Vehicle Combinations A Literature Survey

SUMMARY

This paper presents a review of theoretical and experimental works relative to the handling performance of commercial vehicle combinations. A commercial vehicle combination (road train) is defined as a tractor unit and an arbitrary number of trailers. The review contains literature corresponding the most widely used types of trains: tractor-semitrailer, truck-trailer and tractor-semitrailer-semitrailer (doubles). The vehicle dynamic performance has been investigated taking into consideration the following features: directional performance, roll dynamics, braking performance and combined braking and directional performance. With the aim of evaluating the present state of research activities in the field of lateral dynamics of articulated commercial vehicles, the author has compiled some 250 references.     

Rollover prevention for heavy trucks using frequency shaped sliding mode control

Control and handling of heavy commercial vehicles carrying liquid cargo are influenced by liquid movement within the partially filled tank. During steering and braking maneuvering tasks, the truck may exhibit unstable behavior at lateral acceleration levels of 0.3 g to 0.4 g [m/s²]. The fluid slosh forces and dynamic load transfers in the lateral and longitudinal directions and parametric uncertainties caused by moving liquid cargo affect the overall dynamics of the vehicle. To solve a physical problem about the minimal excitation of the slosh dynamics associated with the longitudinal and lateral excitation of the vehicle, dynamic sliding surface design combined with recursive backstepping algorithm is introduced. Compensator dynamics are introduced in the sliding mode through a class of switching surfaces which has the interpretation of linear operators such that the resulting closed-loop system retains the insensitivity to uncertainties in the sliding mode while minimizing the excitation of flexible modes and unmodeled dynamics. The frequency shaped backstepping sliding mode algorithm, proposed by Acarman and Özgüner [Frequency shaping compensation for backstepping sliding mode control. Paper presented at the 15th IFAC World Congress, Barcelona, Spain, 2002], is designed to stabilize and to attenuate the sloshing effects of moving cargo by properly choosing the crossover frequencies of the dynamic compensators in accordance with the fundamental frequencies of the slosh dynamics.     

On the handling performance of a vehicle with different front-to-rear wheel torque distributions

ABSTRACT

The handling characteristic is a classical topic of vehicle dynamics. Usually, vehicle handling is studied by analyzing the understeer coefficient in quasi-steady-state maneuvers. In this paper, experimental tests are performed on an electric vehicle with four independent motors, which is able to reproduce front-wheel-drive, rear-wheel-drive and all-wheel-drive (FWD, RWD and AWD, respectively) architectures. The handling characteristics of each architecture are inferred through classical and new concepts. The study presents a procedure to compute the longitudinal and lateral tire forces, which is based on a first estimate and a subsequent correction of the tire forces that guarantee the equilibrium. A yaw moment analysis is performed to identify the contributions of the longitudinal and lateral forces. The results show a good agreement between the classical and new formulations of the understeer coefficient, and allow to infer a relationship between the understeer coefficient and the yaw moment analysis. The handling characteristics vary with speed and front-to-rear wheel torque distribution. An apparently surprising result arises at low speed: the RWD architecture is the most understeering configuration. This is discussed by analyzing the yaw moment caused by the longitudinal forces of the front tires, which is significant for high values of lateral acceleration and steering angle.     

Actuator optimal placement studies of high-speed power bogie for active hunting stability

ABSTRACT

We put forward three actuator placements of the high-speed train power bogie to improve the train hunting stability. The active control forces act on the frame, between the frame and the motor, and on the motor by the inertial or retractable actuator, respectively, based on the feedback states of vibration velocity of the front and rear end beams. The feedback gains and the motor suspension parameters in different cases are optimised with the two objectives of system stability margin and control effort. The required actuator outputs of the three cases are compared based on the theoretical analysis with a 8 DOF bogie model. The results show that the three control cases can effectively improve the hunting stability, especially at high speed. The active control of motor lateral movement is helpful to increase the dynamic vibration absorbing function of the motor flexible suspension, and the control output is obviously smaller than the other two control cases. In addition, the influence of system delay on stability was analysed and we could use or avoid the effects of delay on the stability.     

The Influence of Structural Flexibilities on the Straight-running Stability of Motorcycles

A new tyre model for studies of motorcycle lateral dynamics, and three new motorcycle models, each incorporating a different form of structural compliance, are developed. The tyre model is based on “taut string” ideas, and includes consideration of tread width and longitudinal tread rubber distortion and tread mass effects, and normal load variation. Parameter values appropriate to a typical motorcycle tyre are employed. The motorcycle models are for small lateral perturbations from straight running at constant speed, and include (a) lateral compliance of the front wheel in the front forks, (b) torsional compliance of the front forks, and (c) torsional compliance in the rear frame at the steering head about an axis perpendicular to the steering axis.

Results in the form of eigenvalues, indicating modal damping properties and natural frequencies are presented for each model. The properties of four large production machines for a range of forward speeds, and the practicable range of stiffnesses are calculated, and the implications are discussed.

It is concluded that typical levels of structural compliance in models (a) and (c) contribute significantly to the steering behaviour properties of large motorcycles, and their observed behaviour can be understood better in terms of the new results than of those existing previously. Some conclusions relating to optimal structural stiffness properties are also drawn.     

Steering and Dynamic Stability of Railway Vehicles

SUMMARY

For railway vehicles having coned wheels mounted on solid axles there is a conflict between dynamic stability and steering ability

It is shown that the stiffness and kinematic properties of all possible interwheelset connections are characterised by two properties describing the distortional characteristics of the vehicle in plan. Within this framework, the various possibilities for steered wheelsets are considered, and several past and current proposals are reviewed. Using the linear approach to dynamic stabibty and curve negotation the performance of existing and newly proposed configurations is discussed

For any symmetric, two-axle vehicle it is shown that for perfect steering on a curve there should be zero bending stiffness between the wheelsets. It is further shown that if the bending stiffness is zero, the vehicle lacks dynamic stability as the critical speed of instability, is zero. In this case, the vehicle undergoes a steering oscillation which occurs at the kinematic frequency of a single wheelset and which is a motion in which pure rolling occurs

Similar results are obtained with vehicles with three or more axles if adjacent axles are connected by shear structures. However, it is shown that it is possible to satisfy both the requirements of perfect steering and a non-zero critical speed if the vehicle has zero bending stiffness and if, in addition to adjacent wheelsets being connected in shear, at least one pair of non-adjacent axles are connected by a shear structure.     

Study of the Pneumatic Tyre Behaviour on Dry and Rigid Road by Finite Element Method

SUMMARY

The paper presents a physical tyre model capable of describing the complete pneumatic tyre behaviour during steady and transient states. Given the radial deflection, the longitudinal and lateral slip, the camber angle, the inner pressure and the mechanical parameters describing the tyre structure, the model returns the vertical load, the longitudinal and lateral forces, the self aligning torque. Particular attention has been devoted to the computation (by f.e.m.) of tyre carcass and tread deformations; it is explained how side force increases by moderate braking at constant slip angle. An experimental verification validates the model, although more studies could be needed to improve model effectiveness.     

Energy Flow Method for the Study of Motorcycle Wobble Mode

SUMMARY

A concept of the energy flow is introduced in order to study the motorcycle wobble mode. The activation mechanism of the wobble oscillation is made clear in the framework of the energy flow concept It is found that the wobble mode is activated mainly by the yaw rate and roll rate motion and is suppressed by the lateral acceleration and the force of the front time. A designing guide to stabilize the wobble mode is mentioned.     

An Evaluation of Passive Automotive Suspension Systems with Variable Stiffness and Damping Parameters

SUMMARY

Passenger discomfort, suspension working space and dynamic tyre loading parameters are calculated for different combinations of spring stiffness and damping coefficient representing the suspension system in a quarter car model subject to realistic random disturbance inputs from roads of widely differing quality. Sprung and unsprung masses and the tyre vertical stiffness and damping coefficient employed derive from a current production car. Designs which are best for the specific conditions represented are identified and their performance properties in other (off-design) conditions are considered, and conventional design is explained as the inevitable consequence of the need to compromise if fixed suspension parameters are used. Performance improvements possible if variable parameters can be employed are evaluated as a function of the ranges of variability provided, and a stratagem for controlling parameters is proposed.     

汽车操纵稳定性的中间位置转向试验

操纵稳定性中间位置转向试验最初是由美国德尔福公司制定的，是汽车在高速行驶条件下操纵性和稳定性的重要评价方法。通过试验的原始数据可以绘制出转向盘转角与侧向加速度、转向盘力矩与侧向加速度、转向盘力矩与转向盘转角等多条特性曲线，以作为不同的评价指标。以CAll41载货汽车作为实例分析，发现该车转向干摩擦偏大，转向刚度偏低，高速行驶时的非线性路感不够理想。     

Forced Steering of Rail Vehicles: Stability and Curving Mechanics

SUMMARY

A forced steering rail vehicle employs linkages between.the carbody and wheelsets to force a more radial wheelset alignment. It is shown that the curve negotiation capability of forced steering trucks is significantly improved over conventional and self steering radial trucks. Parametric curves are presented showing angle-of-attack and lateral flange force as a function of steering gain parameters and truck bending stiffness. It is also shown that the forced steering concept can produce kinematic instability and severely reduced critical speeds for low conicities and creep coefficients. Analytic expressions are derived that illustrate how these kinematic instabilities can be avoided.