Rail Vehicles' Riding Quality and Comfort Related to Theoretical and Experimental Optimization Application to High Speed Trains

SUMMARY

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

Validation of an Articulated Vehicle Simulation

SUMMARY

Tests were performed on a typical UK articulated vehicle to measure dynamic tyre forces and sprung mass accelerations. The measured road profile data and vehicle response data are used to determine some of the important characteristics of articulated vehicle vibration behaviour. In particular, roll motions and their effect on dynamic tyre forces are examined. The measured data are used to validate two and three-dimensional computer models of the vehicle. Attention is given to modelling the tandem leaf-spring trailer suspension. The conditions under which a two-dimensional model can accurately simulate vehicle behaviour are examined.     

The Steering Characteristics of Multiple Axle Bogie Systems

SUMMARY

Legislation limits the load that may be transferred to the roadway by the axies of a commercial vehicle and this has resulted in the development of multi axle bogies for both the tractor and trailer units of articulated vehicles and at the rear of rigid vehicles, some of these bogies contain self steering or articulation steered axles

Experience shows that the tyre wear characteristics of multi axle bogies may be unsatisfactory. The paper analyses the role of such bogies in the context of vehicle handling and shows how the lateral tyre forces vary between the axles. An hypotheses relating the forces in a steady state turn to wear is given. The analysis may also be applied to the general case of vehicle handling.     

Straight-ahead running of road vehicles – analytical formulae including full tyre characteristics

ABSTRACT

During straight-ahead running, the longitudinal axis of road vehicles, notably cars, is not parallel to road axis. This occurrence is general and is due both to road cross slope (road banking) and to tyre characteristics, particularly ply-steer and conicity. In order to describe such a phenomenon, the paper develops a new and relatively simple analytical model. Despite the model is linear, the solution which is provided is exact, since straight-ahead motion occurs with small angles and both the elastokinematics of suspension system and tyre characteristics can be modelled by linearised equations. The Handling Diagram theory is updated and completed by introducing the actual shifts of tyre characteristics. The validation of the analytical expressions is performed by using a MSC Adams^TM full model of a car. A subjective-objective experimental test campaign provides preliminary substantiation of the ability of the derived formulae to describe tyre performance. By means of the unreferenced analytical formulae developed in the paper, we allow, given the vehicle, the proper tyre design specification and vice-versa. In particular, a formula is given to make null the steering torque during straight-ahead driving. The derived analytical formulae may provide a sound understanding of the straight-ahead running of road vehicles.     

Shear forces in the contact patch of a braked-racing tyre

This article identifies tyre modelling features that are fundamental to the accurate simulation of the shear forces in the contact patch of a steady-rolling, slipping and cambered racing tyre. The features investigated include contact patch shape, contact pressure distribution, carcass flexibility, rolling radius (RR) variations and friction coefficient. Using a previously described physical tyre model of modular nature, validated for static conditions, the influence of each feature on the shear forces generated is examined under different running conditions, including normal loads of 1500, 3000 and 4500 N, camber angles of 0° and?3°, and longitudinal slip ratios from 0 to?20%. Special attention is paid to heavy braking, in which context the aligning moment is of great interest in terms of its connection with the limit-handling feel. The results of the simulations reveal that true representations of the contact patch shape, carcass flexibility and lateral RR variation are essential for an accurate prediction of the distribution and the magnitude of the shear forces generated at the tread–road interface of the cambered tyre. Independent of the camber angle, the contact pressure distribution primarily influences the shear force distribution and the slip characteristics around the peak longitudinal force. At low brake-slip ratios, the friction coefficient affects the shear forces in terms of their distribution, while, at medium to high-slip ratios, the force magnitude is significantly affected. On the one hand, these findings help in the creation of efficient yet accurate tyre models. On the other hand, the research results allow improved understanding of how individual tyre components affect the generation of shear forces in the contact patch of a rolling and slipping tyre.     

接地面部分溶化条件下冰面轮胎摩擦力的研究

综合运用流体动力润滑理论的能量守恒定律，提出了接地面部分溶化条件下冰面上汽车轮胎的摩擦力或牵引力的理论计算模型。证明了正常工作条件下，接地面上冰产生溶化的可能。对不同制动和驱动条件下轮胎摩擦力进行了计算，取得了同试验数据吻合很好的预测结果。并同已有预测模型进行了比较，比较结果表明：本文依据严格的润滑理论所推导出的冰面轮胎牵引力模型比其它已有理论模型更接近试验结果。     

New tyre-road contact model for applications at low speed

Most of the tyre models have been developed for high speed, combined forces, etc., however, in certain tests it is necessary to know tyre behaviour at very low speed in order to evaluate different systems. So, during vehicle inspection and maintenance of the steering and brake system, by means of sideslip tester and roller brake tester respectively, the forces transmitted by the tyres are measured; all of these inspections are carried out at low speeds. Furthermore, usually, automobile vehicles run at low speeds during an important part of their operating life (less than 60 km/h), mainly during urban traffic, and in steady state conditions. Therefore, it is particularly interesting to develop an accurate model of the contact patch tyrepavement for low speeds without the complexity of models that cover a wide speed range but provide less precision at very low speeds. The dynamometer plate has proved to be an appropriate test equipment to characterise the tyre-pavement contact at low speed and the steering geometry and wheel alignment. It has the feature of being able to carry out tests with the tyre installed in the vehicle as in completely real conditions. The main aim of this research is to set up a contact model between tyre and pavement at very low speed based on the measurement of longitudinal and lateral forces. A test methodology that allows carrying out the experimental tests in a systematic and controlled way with the dynamometer plate has also been developed. From this model it will be possible to estimate the forces that tyres are capable of transmitting in different situations to act in the parameters which affect these forces and maximize them.     

A novel semi-empirical tyre model for combined slips

A new tyre-force model for simultaneous braking and cornering is presented, which is based on combining existing empirical models for pure braking and cornering with brush-model tyre mechanics. The aim is to offer an easy-to-use, accurate model for vehicle-handling simulations. On a working tyre the contact patch between the tyre and the road is, in general, divided into an adhesion region where the rubber is gripping the road and a sliding region where the rubber slides on the road surface. The total force generated by the tyre is then composed of components from these two regions. The brush model describes this in a mechanical framework. The proposed model is based on a new method to extract adhesion and sliding forces from empirical pure-slip tyre models. These forces are then scaled to account for the combined-slip condition. The combined-slip self-aligning torque is also described. A particular feature of the model is the inclusion of velocity dependence, even if this is not explicitly present in the empirical pure-slip model. The approach is quite different from most previous combined-slip models, in that it is based on a rather detailed mechanical model in combination with empirical pure-slip models. The model is computationally sound and efficient and does not rely on any additional parameters that depend on combined-slip data for calibration. It can be used in combination with virtually any empirical pure-slip model and in this work the Magic Formula is used in examples. Results show good correspondence with experimental data.     

Noise,vibration, harshness model of a rotating tyre

ABSTRACT

The tyre plays a fundamental role in the generation of acoustically perceptible driving noise and vibrations inside the vehicle. An essential part of these vibrations is induced by the road excitation and transferred via the tyre into the vehicle. There are two basic ways to study noise, vibration, harshness (NVH) behaviour: Simulations in time and frequency domains. Modelling the tyre transfer behaviour in frequency domain requires special attention to the rotation of the tyre. This paper shows the approach taken by the authors to include the transfer behaviour in the frequency range up to 250?Hz from geometric road excitations to resulting spindle forces in frequency domain. This paper validates the derived NVH tyre model by comparison with appropriate transient simulations of the base transient model.     

Vehicle-Generated Road Damage: A Review

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

Influence of tyre–road contact model on vehicle vibration response

The influence of the tyre–road contact model on the simulated vertical vibration response was analysed. Three contact models were compared: tyre–road point contact model, moving averaged profile and tyre-enveloping model. In total, 1600 real asphalt concrete and Portland cement concrete longitudinal road profiles were processed. The linear planar model of automobile with 12 degrees of freedom (DOF) was used. Five vibration responses as the measures of ride comfort, ride safety and dynamic load of cargo were investigated. The results were calculated as a function of vibration response, vehicle velocity, road quality and road surface type. The marked differences in the dynamic tyre forces and the negligible differences in the ride comfort quantities were observed among the tyre–road contact models. The seat acceleration response for three contact models and 331 DOF multibody model of the truck semi-trailer was compared with the measured response for a known profile of test section.     

Sliding mode-based lateral vehicle dynamics control using tyre force measurements

In this work, a lateral vehicle dynamics control based on tyre force measurements is proposed. Most of the lateral vehicle dynamics control schemes are based on yaw rate whereas tyre forces are the most important variables in vehicle dynamics as tyres are the only contact points between the vehicle and road. In the proposed method, active front steering is employed to uniformly distribute the required lateral force among the front left and right tyres. The force distribution is quantified through the tyre utilisation coefficients. In order to address the nonlinearities and uncertainties of the vehicle model, a gain scheduling sliding-mode control technique is used. In addition to stabilising the lateral dynamics, the proposed controller is able to maintain maximum lateral acceleration. The proposed method is tested and validated on a multi-body vehicle simulator.     

Tyre–road grip coefficient assessment – Part II: online estimation using instrumented vehicle,extended Kalman filter,and neural network

The main objective of this work is to determine the limit of safe driving conditions by identifying the maximal friction coefficient in a real vehicle. The study will focus on finding a method to determine this limit before reaching the skid, which is valuable information in the context of traffic safety. Since it is not possible to measure the friction coefficient directly, it will be estimated using the appropriate tools in order to get the most accurate information. A real vehicle is instrumented to collect information of general kinematics and steering tie-rod forces. A real-time algorithm is developed to estimate forces and aligning torque in the tyres using an extended Kalman filter and neural networks techniques. The methodology is based on determining the aligning torque; this variable allows evaluation of the behaviour of the tyre. It transmits interesting information from the tyre–road contact and can be used to predict the maximal tyre grip and safety margin. The maximal grip coefficient is estimated according to a knowledge base, extracted from computer simulation of a high detailed three-dimensional model, using Adams^® software. The proposed methodology is validated and applied to real driving conditions, in which maximal grip and safety margin are properly estimated.     

Investigation of Features of Tyre Rolling at Non-Small Velocities on the Basis of a Simple Tyre Model with Distributed Mass Periphery

SUMMARY

On the basis of the brush-type tyre model the paper considers the interaction between steady-state rolling deformable wheel and flat road surface as well as corresponding force and moment characteristics of the wheel.

At least two zones of sliding, anisotropic dry friction, sliding friction coefficient speed-dependent and instantaneous leap of the friction coefficient when transition from sliding to adhesion zone occurs, have been taken into account, as well as distributed peripheral mass of tyre, elasticity, pseudo-dry friction and damping properties in radial, tangential and lateral directions of the elements at the wheel periphery, including a visco-elastic belt. Vertical force distribution in the contact area is not supposed to be known in advance and follows from the calculation. As a result, sliding zone lengths, distributed forces in contact area, six components of generalized road reaction reduced to the wheel center, and rolling resistance moment are found as functions of vertical load, movement velocity, longitudinal and side slip, friction in contact area with road, stiffnesses, dry friction and damping in the tyre model elements and of distributed peripheral mass.

A computer program developed in Fortran and results of calculations are of particular interest for qualitative analysis including steady rolling of studded tyre and also racing car and aircraft tyres which peripheral mass shows itself in a special way because of great movement velocities.     

Analysis of wheel speed vibrations for road friction classification

ABSTRACT

With higher level of vehicle automation, it becomes increasingly important to know the maximum possible tyre forces during normal driving. An interesting method in this respect is estimating the tyre–road friction from the resonance peak in the wheel speed signal, excited by road roughness. A simulation environment using the MF-Swift tyre model is proposed, which gives insight in the correctness and functioning of this method. From implementing the estimation algorithm and considering the tyre torsional vibration system, it is concluded that frequencies and damping ratios can be estimated with reasonable accuracy and that the trends observed with changing road friction are consistent. Furthermore, the proposed simulation environment gives opportunity to investigate other issues like robustness of the estimation method to road roughness. Additionally, the tyre modelling aspect of the estimation method is analysed and improvements are proposed.