Integrated fault detection and diagnosis system for longitudinal control of an autonomous all-terrain vehicle (ATV)

This paper presents a fault detection and diagnosis (FDD) method to enhance the reliability and safety for longitudinal control of an autonomous all-terrain vehicle (ATV). An integrated approach using decentralized and centralized FDD is proposed to optimize the tradeoff between sensitivity and robustness. While the decentralized approach is suitable for detecting faults in actuators and sensors directly connected to a single processor, it is sensitive to noises and disturbances and thus may result in false alarms. On the other hand, the centralized approach is based on information communicated between multiple processors, and it detects and diagnoses faults through analyzing concurrent computations of multiple hardware modules. However, its performance is still limited to isolating faults specifically in terms of components in the single hardware. To incorporate the advantages of both FDD approaches, a two-layered structure integrating both decentralized and centralized FDD is proposed and allows us to perform more robust fault detection as well as more detailed fault isolation. Finally, the proposed method is validated experimentally via field tests of an ATV.     

线控转向系统故障检测及容错控制协同设计

为解决线控转向系统故障可能导致车辆失控的问题,提出一种故障检测及容错控制协同设计方法。首先,建立了包含线控转向系统加性故障的车辆动力学模型;其次,联合车辆动力学模型及故障检测/容错控制器,建立跟踪误差闭环控制系统;然后,求解满足闭环系统H∞性能的线性矩阵不等式,得到故障检测/容错控制器参数;最后,基于dSPACE Full-Size HIL进行硬件在环仿真测试。结果表明,该方法可快速检测出转向系统故障,同时实现了车辆的容错控制。     

Fault-tolerant control of heavy-haul trains

The fault-tolerant control (FTC) of heavy-haul trains is discussed on the basis of the speed regulation proposed in previous works. The fault modes of trains are assumed and the corresponding fault detection and isolation (FDI) are studied. The FDI of sensor faults is based on a geometric approach for residual generators. The FDI of a braking system is based on the observation of the steady-state speed. From the difference of the steady-state speeds between the fault system and the faultless system, one can get fault information. Simulation tests were conducted on the suitability of the FDIs and the redesigned speed regulators. It is shown that the proposed FTC does not explicitly worsen the performance of the speed regulator in the case of a faultless system, while it obviously improves the performance of the speed regulator in the case of a faulty system.     

Trends in vehicle motion control for automated driving on public roads

ABSTRACT

In this paper, we describe how vehicle systems and the vehicle motion control are affected by automated driving on public roads. We describe the redundancy needed for a road vehicle to meet certain safety goals. The concept of system safety as well as system solutions to fault tolerant actuation of steering and braking and the associated fault tolerant power supply is described. Notably restriction of the operational domain in case of reduced capability of the driving automation system is discussed. Further we consider path tracking, state estimation of vehicle motion control required for automated driving as well as an example of a minimum risk manoeuver and redundant steering by means of differential braking. The steering by differential braking could offer heterogeneous or dissimilar redundancy that complements the redundancy of described fault tolerant steering systems for driving automation equipped vehicles. Finally, the important topic of verification of driving automation systems is addressed.     

A modified integral sliding mode control to lateral stabilisation of 4-wheel independent drive electric vehicles

This paper presents a novel sliding mode controller (SMC) and its application in the lateral stability control of a 4-wheel independent drive electric vehicle. The structure of the SMC is modified and online-tuned to ensure vehicle system stability, and to track the desired vehicle motion references when an in-wheel motor fault happens. The proposed controller is faster, more accurate, more robust, and with smaller chattering than common SMCs chatter. The effectiveness of the introduced approach is investigated through conducted simulations in the CARSIM and MATLAB software environments.     

汽车EPS与SAS故障诊断系统的开发

摘要：故障诊断技术是汽车技术研究的热点之一,由于电动助力转向系统（EPS）和半主动悬架系统（SAS）已成为转向和悬架机构的发展方向,文章基于VB和SQLServer软件平台开发出底盘EPS与SAS故障诊断系统．．利用专家系统的智能诊断功能,根据故障现象的观察和信号采集进行问诊操作,快速分析和查明原因并显示出故障原因与解决方法,通过故障诊断实例与实际故障的对比表明,开发的故障诊断系统能够对EPS与SAS的故障进行正确的诊断,从而为汽车底盘系统的故障诊断探索出一种有效和可行的方法。,     

Bolster spring fault detection strategy for heavy haul wagons

An on-board health monitoring system is proposed for heavy haul wagons in this paper including a signal-based fault detection and isolation (FDI) method and an on-line fault diagnose strategy. Such a system, to be feasible on freight wagons, must be sufficiently cheap and robust, hence the design assumes the constraint of using only two accelerometers mounted on the front left and right rear part of each carbody in a heavy haul train. This paper focuses on the detection of bolster spring fault conditions. The problem is made more complex by the modes of failure which might be expected in bolster spring nests. Types of spring failure are firstly identified and discussed covering situations of broken (shortening springs) and softening (individual spring loss from a nest or cross-section loss through corrosion). The effects of these faults and their detectability were investigated using simulations on straight and curved track and using a fully detailed model of a typical 40?t axle-load heavy haul wagon. The simulation results were then examined and compared using cross-correlation analysis and an FDI system was proposed. The FDI system introduced five possible fault indicators. Initial results indicated that it was possible to detect changes in bolster stiffness of ±25%. An on-line fault diagnoses strategy is proposed for bolster spring faults which only requires data from wagon monitoring during travel around sharp curves to detect and the occurrence of confirm faults. The functionality envisaged needs only a ‘once per trip’ monitoring site, such as a sharper curve, and is aimed at condition monitoring rather than the provision of alarms or comprehensive monitoring of all events.     

故障树与专家规则的车载故障诊断专家系统

文章旨在开发一种随车故障诊断专家系统,指导用户自行排除故障。提出了将故障树分析法与基于规则的专家系统相结合构建的故障诊断专家系统;以Windows CE和S3C2440A为平台,以EVC＋＋为编程语言,开发出具有友好的人机交互界面车载汽车故障诊断专家系统,该系统通过用户选择故障现象,便提示可能发生的原因和维修建议;并以发动机无力为例进行诊断,验证了该系统的有效性和实用性。该系统具有一定的创新性,对我国汽车修理行业具有很大的实用价值。     

Application of observer-based fault detection in vehicle roll control

This paper describes how observer-based techniques for intelligent fault detection were applied to monitoring an active suspension control system in an experimental articulated heavy vehicle. The aim was to define a practical method for detecting faults, taking into account the nonlinearities of the vehicle. The experimental vehicle was divided conceptually into subsystems, namely the passive dynamics of the trailer, the dynamics of the hydraulic actuators, and the expected response of the closed-loop system. A linear dynamic model was designed for each subsystem. A fault detection observer was then designed for each dynamic model. The observer feedback gains were chosen to optimise estimation by the observer residual of specified errors on the output measurements. The observer residuals were then normalised and combined logically to provide a fault diagnosis. The performance of the fault detection scheme is demonstrated in the case of sensor faults and changes in the operation of the active control system.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

车用发动机过热故障树分析

应用故障树分析方法,对某车用发动机冷却系统过热故障进行分析。给出了冷却系统过热故障的各种原因及其组合方式,进行了故障树的定性分析和定量计算。遵循故障树定性分析所得出的最小割集,可以方便快捷地查找到引起顶事件的底事件故障,以便采取有效措施预防发动机冷却系统过热故障的发生或减小其发生概率。     

汽车纵向加/减速度多模型分层切换控制

针对汽车纵向动力学模型的大不确定性,设计了一种基于鲁棒控制理论的汽车纵向加速度多模型分层切换控制系统。通过分析汽车纵向动力学特性,用4个不确定模型覆盖对象不确定性,并应用LM I方法设计对应的鲁棒性能控制器集合。考虑鲁棒控制系统的特点,设计了一种对不确定性的系统增益进行估计的切换指标函数,以选择控制器进行控制。实验表明,提出的方法在大不确定性下可以对纵向加速度有效控制。     

高压共轨式电控柴油机电子油门故障自诊断策略研究

根据电子油门传感器的特点闸述了其故障自诊断的原理，介绍了电子油门诊断法中的极值诊断法和逻辑性诊断法，对油门传感器发生故障后的失效处理工作模式进行了讨论。建立了电子油门故障诊断的仿真模型，其仿真结果表明该控制策略能及时地发现故障。     

风神蓝鸟轿车ABS故障检测与诊断

介绍了蓝鸟系列轿车ABS自诊断系统中故障诊断以及故障码的读取与清除方法。在介绍ABS常见典型故障的基础上,分析了如何根据故障码进行传感器、执行器电磁阀、ABS电动机继电器、ABS控制元件以及系统低电压的故障诊断方法,论述了常见的故障现象以及诊断程序,给出了系统维修数据。     

Design and Evaluation of Robust Cooperative Adaptive Cruise Control Systems in Parameter Space

This paper is on the design of cooperative adaptive cruise control systems for automated driving of platoons of vehicles in the longitudinal direction. Longitudinal models of vehicles with simple dynamics, an uncertain first order time constant and vehicle to vehicle communication with a communication delay are used in the vehicle modeling. A robust parameter space approach is developed and applied to the design of the cooperative adaptive cruise control system. D-stability is chosen as the robust performance goal and the feedback PD controller is designed in controller parameter space to achieve this D-stability goal for a range of possible longitudinal dynamics time constants and different values of time gap. Preceding vehicle acceleration is sent to the ego vehicle using vehicle to vehicle communication and a feedforward controller is used in this inter-vehicle loop to improve performance. Simulation results of an eight vehicle platoon of heterogeneous vehicles are presented and evaluated to demonstrate the efficiency of the proposed design method. Also, the proposed method is compared with a benchmark controller and the feedback only controller. Time gap regulation and string stability are used to assess performance and the effect of the vehicle to vehicle communication frequency on control system performance is also investigated.     

An optimal model-based trajectory following architecture synthesising the lateral adaptive preview strategy and longitudinal velocity planning for highly automated vehicle

Automated driving has received a broad of attentions from the academia and industry, since it is effective to greatly reduce the severity of potential traffic accidents and achieve the ultimate automobile safety and comfort. This paper presents an optimal model-based trajectory following architecture for highly automated vehicle in its driving tasks such as automated guidance or lane keeping, which includes a velocity-planning module, a steering controller and a velocity-tracking controller. The velocity-planning module considering the optimal time-consuming and passenger comforts simultaneously could generate a smooth velocity profile. The robust sliding mode control (SMC) steering controller with adaptive preview time strategy could not only track the target path well, but also avoid a big lateral acceleration occurred in its path-tracking progress due to a fuzzy-adaptive preview time mechanism introduced. In addition, an SMC controller with input–output linearisation method for velocity tracking is built and validated. Simulation results show this trajectory following architecture are effective and feasible for high automated driving vehicle, comparing with the Driver-in-the-Loop simulations performed by an experienced driver and novice driver, respectively. The simulation results demonstrate that the present trajectory following architecture could plan a satisfying longitudinal speed profile, track the target path well and safely when dealing with different road geometry structure, it ensures a good time efficiency and driving comfort simultaneously.     

Bootstrap法在车辆故障检测中的研究及应用

介绍Bootstrap方法的原理并将Bootstrap方法应用于检测车辆中存在的故障,通过计算不同故障下的车辆样本之间均匀Kullback-Lcible距离的均值以及在给定置信度下的置信区间等特征值来反映被测车辆的故障种类。给出一种新的随机数产生器用在Bcotstrap法重采样中产生新的随机序列。以车辆卜的驱动桥为检测对象对该算法进行了验证,结果表明该算法能准确检测出驱动桥所存在的故障。     

Optimal roll control of an articulated vehicle: theory and model validation

This paper investigates optimal roll control of an experimental articulated vehicle. The test vehicle and the mathematical model used to design the control strategies are presented. The vehicle model is validated against experimental data from the test vehicle in passive configuration. The initial controller design, performed by Sampson (Sampson, D.J.M. and Cebon, D., 2003a, Achievable roll stability of heavy road vehicles. Proc. Instn. Mech. Engrs, Part D, J. Automobile Engineering, 217(4), 269–287), is reviewed and adapted for the experimental vehicle. The effect of not controlling all the axles on the vehicle is investigated and a variable vehicle speed controller is designed by interpolating between constant speed controllers. Substantial reduction in normalized load transfer is achieved for a range of manoeuvres, both in steady-state and transient conditions.     

Automatic Steering Based on Roadway Markers: From Highway Driving to Precision Docking

Bus Rapid Transit (BRT) is an effective alternative for providing rail-like corridor transit service. An advanced BRT concept involves the use of automated buses to provide functions of a rail transit system. A vehicle under automatic steering control following a prescribed trajectory is operated like a train on a rail. A lateral position sensing that uses roadway markers, such as magnetic markers embedded under the roadway, as lateral reference is one of the promising approaches for a reliable sensing system. The BRT concept requires the steering control system to consistently perform all necessary steering functions from high speed driving to low speed precision docking. This paper describes a single steering controller that achieves all performance objectives. Various data collected during several public demonstrations are presented in this paper to illustrate the effectiveness of the approach. These data include the following automatic steering control scenarios: over 100 mph high-speed driving, high-g maneuvers, sharp curve following, and low speed precision docking.     

Automatic Steering Based on Roadway Markers: From Highway Driving to Precision Docking

Bus Rapid Transit (BRT) is an effective alternative for providing rail-like corridor transit service. An advanced BRT concept involves the use of automated buses to provide functions of a rail transit system. A vehicle under automatic steering control following a prescribed trajectory is operated like a train on a rail. A lateral position sensing that uses roadway markers, such as magnetic markers embedded under the roadway, as lateral reference is one of the promising approaches for a reliable sensing system. The BRT concept requires the steering control system to consistently perform all necessary steering functions from high speed driving to low speed precision docking. This paper describes a single steering controller that achieves all performance objectives. Various data collected during several public demonstrations are presented in this paper to illustrate the effectiveness of the approach. These data include the following automatic steering control scenarios: over 100 mph high-speed driving, high-g maneuvers, sharp curve following, and low speed precision docking.