共查询到18条相似文献,搜索用时 203 毫秒
1.
2.
本文分析了我国现生产双涡轮液力变矩器中存在的一些问题;提出了改进方案;编订了特性计算一系列公式及计算过程的电子计算机程序,就所编程序一次算出的二千八百多个数据绘制并分析了其中一部分特性曲线;并对所编程序在今后提高性能的研究和进行变矩器系列化工作中的辅助作用作了阐述。 相似文献
3.
轿车液力变矩器的改进设计方法研究 总被引:2,自引:0,他引:2
由于工作介质流动状况复杂,难以形成准确、可靠的轿车液力变矩器设计方法,本文建立了液力变矩器内流场的计算模型,得到了正确,可信的轿车液力变矩器内流场计算结果,在分析后,本文认为泵轮流道入口处的径向扩张影响了液力变矩器的性能,依此,本文成功地改进了该液力变矩器。 相似文献
4.
液力变矩器计算机辅助设计与制造 总被引:5,自引:0,他引:5
本文简述了液力变矩器设计与制造的研究和发展,以及计算机在液力变矩器设计与制造行业的应用,指出了存在的问题;建立了液力变矩器计算机辅助设计与制造的一体化系统;实现了液力变矩器性能预估、叶形判断与叶栅系统入,出口参数计算的有机统一。 相似文献
5.
为了研究叶片数变化对液力变矩器原始特性的影响,通过Imageware逆向建模得到了变矩器的流道模型,并进行了高速比工况下的三维流场计算,根据计算结果分析了不同工作轮叶片数对变矩器原始特性的影响;选取4种典型工作轮叶片数的组合方案进行台架试验,对计算结果进行验证。结果表明:试验与计算结果平均误差为3.1%,最大误差为4.2%,证明三维流场计算结果是准确的,采用三维流场计算液力变矩器性能是可行的。 相似文献
6.
赵新民 《筑路机械与施工机械化》2013,30(6)
对某型液力传动地下铲运机的柴油发动机、液力变矩器以及共同工作特性进行研究,并进行动力学和运动学分析.根据柴油发动机外特性曲线以及液力变矩器的原始特性参数,计算了柴油发动机机和液力变矩器两者共同工作的输出特性,得到了各挡牵引特性,为该地下铲运机总体设计提供了可靠依据. 相似文献
7.
8.
通过对推土机的发动机、液力变矩器和液压系统等主要发热部件发热量的计算,对液力机械式履带推土机的热平衡问题进行了分析,并提出了热平衡设计的评价指标,可为推土机的优化设计提供借鉴. 相似文献
9.
10.
综述了液力变矩器优化设计过程中各个阶段的研究进展和现状。从液力变矩器设计与参数化方法、设计参数对性能影响、性能预测模型和优化设计方法这4个方面的研究进行论述,并对液力变矩器应用新技术进行了概述。总结每个阶段的研究成果,最后展望了下一步的研究方向。 相似文献
11.
本文推导了适合于液力变矩器叶片设计的S_1流面改进流线曲率法计算方程,提出了流场判别准则和环量分配原则。在此基础上,提出了用多个S_1流面积叠进行变矩器叶片设计的准三维方法,以及在传统的叶片设计方法中加入流场计算环节的叶片设计新途径。并把利用本文提出的设计方法和利用传统的设计方法所设计出来的YB300变矩器进行了特性试验对比,结果表明:新提出的设计方法与传统方法所设计出的变矩器相比,最高效率提高了1.80%,而其它性能基本相同。 相似文献
12.
13.
14.
根据液力变矩器的工作原理及闭锁条件,制定液力变矩器控制策略。利用Simulink建立液力变矩器控制模型,并利用Cruise和Simulink进行联合仿真,验证控制策略的可行性。仿真结果表明,液力变矩器控制模型正确,闭锁离合器能够准确按照闭锁条件闭锁,并且可以显著改善车辆的燃油经济性和排放性能。本文的研究可以为液力变矩器的闭锁研究提供一定的理论依据。 相似文献
15.
16.
《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2012,50(5):283-295
Abstract In this work three first-order nonlinear, nonstationary differential equations describing a hydraulic torque converter in a power transmission system are used. A linear model is obtained on the basis of these equations. This model is verified both theoretically and by an experimental test. On the basis of the calculations the torsional damping was determined. This permitted the damping performance of a power transmission system with a hydraulic torque converter to be defined and established. 相似文献
17.
18.
D. M. Chun J. C. Lee J. C. Yeo S. H. Ahn S. S. Hong J. D. Jang 《International Journal of Automotive Technology》2011,12(2):273-280
In new slim torque converters, lock-up clutches are used to provide high fuel efficiency at low speed. However, the slimness
of the converters causes difficulty in heat dissipation, which may damage the friction material and shorten its life span.
A cooling hole in the lock-up piston reduces the heat but also reduces the torque because oil flows through the hole due to
the pressure difference between the two faces of the piston. In the early stages of the development of this type of torque
converter, designers must consider the minimum flow rate required to cool the friction material and the minimum torque capacity
required to transmit the engine torque. This research explored two methods of estimating these parameters. In the first method,
an estimation equation was derived by combining the response surface method with physical properties such as the centrifugal
force, a sudden expansion, a sudden contraction, and the steady flow energy equation. The second method involved the use of
an artificial neural network. The feasibility of the estimates based on statistics and on the artificial neural network were
confirmed in the design stage by comparing experimental and estimated data. An estimation program was created using the C#.Net
language and has been used for actual torque converter designs by the Korea Powertrain Company. 相似文献