共查询到20条相似文献,搜索用时 93 毫秒
1.
沉管法修建长江越江通道的可行性研究 总被引:1,自引:0,他引:1
在跨越长江的越江通道方式选择中,除了桥梁之外,还有水底隧道。本文根据南京、武汉两城市环境状况及无景规划的要求,从河床断面、工程地质、河段水文、河床稳定性等几个方面分析了采用沉管法修建越江隧道的可行性,并论述了水底隧道的优越性。同时对长江水底隧道的修建方法进行了比较分析,并介绍了南京、武汉两座沉管水底隧道方案研究的概况。 相似文献
2.
3.
赵艳峰 《内蒙古公路与运输》2012,(1):59-60
隧道工程通常包括岩石隧道和软土隧道,一般山体中的隧道多为岩石隧道,因此又称作山岭隧道;而水底或者城市中修建的多为软土隧道,所以称之为城市道路隧道或者水底隧道。文章主要分析了山岭隧道的施工技术以及质量控制措施。 相似文献
4.
浙江甬江水底公路隧道全长1019.528m于1995年11月8日竣工通车,它是我国沿海在近百米深的软土地基上用沉管法施工的第一座水底隧道,设计施工中克服了许多技术难题,经运营半年多的观测管段接头滴水不漏,深受管理单位好评,该隧道修建成功缩短了过江行车时间,方便了两岸群众,具有明显的社会效益和经济效益。 相似文献
5.
6.
作者以南京长江第四通道工可研究报告中隧道推荐方案(石埠桥方案)为例,提出了对水底隧道纵断面线形设计的一些建议及思路。 相似文献
7.
高速铁路水底沉管隧道竖井工程变形沉降问题研究 总被引:1,自引:0,他引:1
在高速铁路越江水底沉管隧道的设计和施工中,竖井连接着沉管管段和暗挖隧道,因上述三个构筑物所处的地质状况差异,产生了不同的沉降量,这对整个沉管隧道有着不利的影响。本文以三维有限元数值计算为依托,对竖井的设计和施工工艺、沉降变形控制等进行了分析。 相似文献
8.
9.
10.
为了解决水底软硬不均地层超大直径盾构施工技术问题,以某水底盾构隧道工程为依托,对超大直径盾构在水底上软下硬地层掘进中面临的技术难点、盾构机选型、施工方案选择、试验段掘进效果、方案可行性以及掘进管理控制等进行了分析和探讨。结果表明,采用有针对性设计功能的盾构机,在低刀盘转速、低掘进速度下,超大直径盾构直接掘进通过水底上软下硬地层的施工方案具有很高的可行性,并得到了成功实施。 相似文献
11.
12.
SMA是沥青码蹄脂碎石(Stone Matrix Asphal)的缩写,是一种以沥青结合料与少量的纤维稳定剂、细集料,以及较多的填料(矿粉)组成的沥青玛蹄脂,填充于间断级配粗集料骨架间隙中组成一体所形成的沥青混合料,简称SMA。该文介绍了SMA在上海的应用及其施工技术。 相似文献
13.
《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2012,50(4):573-596
An existing driver–vehicle model with neuromuscular dynamics is improved in the areas of cognitive delay, intrinsic muscle dynamics and alpha–gamma co-activation. The model is used to investigate the influence of steering torque feedback and neuromuscular dynamics on the vehicle response to lateral force disturbances. When steering torque feedback is present, it is found that the longitudinal position of the lateral disturbance has a significant influence on whether the driver’s reflex response reinforces or attenuates the effect of the disturbance. The response to angle and torque overlay inputs to the steering system is also investigated. The presence of the steering torque feedback reduced the disturbing effect of torque overlay and angle overlay inputs. Reflex action reduced the disturbing effect of a torque overlay input, but increased the disturbing effect of an angle overlay input. Experiments on a driving simulator showed that measured handwheel angle response to an angle overlay input was consistent with the response predicted by the model with reflex action. However, there was significant intra- and inter-subject variability. The results highlight the significance of a driver’s neuromuscular dynamics in determining the vehicle response to disturbances. 相似文献
14.
15.
预应力曲线箱梁和异形箱梁的研究 总被引:7,自引:0,他引:7
近年来 ,国内外学者对曲线箱梁和异形箱梁的静力分析理论和计算方法作过大量的研究 ,但这些理论和方法在某种程度上都存在着一定的局限性 ,特别是在实际设计工作中 ,运用起来不能得心应手。为此本文在综合前人已取得经验下 ,针对桥梁结构设计中分析曲线箱梁、异形箱梁 ,经常遇到的难题进行了研究 ,建立一个较为完善的理论和方法 ,编制了等参元空间分析程序。在实际工程中进行实桥试验 ,验证了本文理论和方法的正确性。本文的研究工作更准确描述了箱梁的荷载响应 ,为设计人员提供直观的设计依据。对曲线箱梁和异形箱梁受力特性有了更一步的理解 ,并提出了新的见解 相似文献
16.
利用AVL公司开发的BOOST软件可宏观地描述发动机的热力学过程且优化发动机的性能,而AVL的CRUISE软件可调用BOOST建立的发动机模型.在进行道路循环工况的仿真时,须对发动机全部工况点进行准确的标定.文中采用BOOST开发了发动机的仿真模型.通过调整节气门开度和燃烧模型参数,标定了发动机在多个转速和负荷点的转矩、功率和油耗,较好地模拟了发动机的动力性和经济性.最后基于ECE循环工况,将此模型与CRUISE进行联合仿真,分析了发动机瞬态工况的动力性、油耗和NO_x排放等参数. 相似文献
17.
混凝土的推广使用已有一个世纪,目前在现代工程建设中仍占有重要的地位。而在今天,混凝土的裂缝较为普遍,在桥梁工程中裂缝几乎无所不在,尽管我们在施工中采取各种各样的措施,但收效甚微,裂缝仍然时有出现。该文指出,究其原因,人们对混凝土温度变化所产生的应力注意不够是其中之一,尤其是大体积混凝土。对此,温度应力与温度控制具有重要的意义。 相似文献
18.
针对互通式立交出口可能出现的多种情况,结合工程实践,探讨其设计技术问题,提出设计思路及技术对策,并在技术分析中强调融入“安全至上”“动态设计”“灵活性设计”“宽容性设计”等设计新理念,使出口设计安全、合理. 相似文献
19.
J. R. Serrano F. J. Arnau V. Dolz A. Tiseira M. Lejeune N. Auffret 《International Journal of Automotive Technology》2008,9(3):277-288
This article presents a two-stage turbocharged heavy-duty diesel (HDD) engine designed to fulfil the US2007 anti-pollution
directive. This directive imposes very restrictive limits on the NOx and particle emissions of HDD engines. In this work,
the possibility of combining particle traps in the exhaust line to reduce soot emissions with very high EGR rates to reduce
NOx emissions is considered. This new generation engine implements two-stage turbocharging in order to improve the bsfc when
the engine is working on steady conditions as well as to optimize the engine transient response. After carrying out the tests,
the results were analyzed and the engine settings were adjusted to maximise its behaviour and minimise pollutant emissions.
NOx and soot emission peaks were also analyzed at engine transient conditions in order to keep them under certain levels,
and thus maintain the overall pollutant emissions to a level that is as low as possible. In summary, a double-stage turbocharging
configuration can greatly improve engine driveability (between 23% and 36% depending on engine speed), while reducing NOx
emissions during transient evolution without increasing opacity peaks beyond the stated limits. 相似文献
20.
介绍了三辊式和三螺杆式气门校正机的机械结构,分析了气门杆部、气门盘部偏歪校正的机理,讨论了机器结构、压辊形状、螺杆形状等对校正质量和效率的影响;对三螺杆式、三辊式、双螺杆式及搓板式气门校正机加以比较,阐述了它们各自的优缺点。 相似文献