Modification of the Highway Capacity Manual two‐lane highway analysis procedure for Spanish conditions

The US Highway Capacity Manual (HCM) methodology is used in Spain to evaluate traffic operation and quality of service. The effect of passing manoeuvre on two‐lane highway operational performance is considered through adjustment factors to average travel speeds and percent time spent following. The procedure is largely based on simulations in TWOPAS and passing behaviours observed during US calibrations in the 1970s. It is not clear whether US driving behaviour and vehicles' performance are comparable with Spanish conditions. The objective of this research is to adapt the HCM 2010 methodology to Spanish driver behaviour, for base conditions (i.e. no passing restrictions). To do so, TWOPAS was calibrated and validated based on current Spanish passing field data. The calibration used a genetic algorithm. The case study included an ideal two‐lane highway with varying directional traffic flow rate, directional split and percentage of trucks. The updated methodology for base conditions is simpler than the current HCM 2010 and does not rely on interpolation from tables. Copyright © 2016 John Wiley & Sons, Ltd.     

Macroscopic modeling of lane‐changing for two‐lane traffic flow

We propose a macroscopic model of lane‐changing that is consistent with car‐following behavior on a two‐lane highway. Using linear stability theory, we find that lane‐changing affects the stable region and the propagation speeds of the first‐order and second‐order waves. In analyzing a small disturbance, our model effectively reproduces certain non‐equilibrium traffic‐flow phenomena—small disturbance instability, stop‐and‐go waves, and local clusters that are affected by lane‐changing. The model also gives the flow‐density relationships in terms of the actual flow rate, the lane‐changing rate, and the difference between the potential flow rate (the flow rate that would have occurred without lane‐changing) and the actual flow rate. The relationships between the actual flow rate and traffic density and between the lane‐changing rate and traffic density follow a reverse‐lambda shape, which is largely consistent with observed traffic phenomena.     

Development of realistic shortest path algorithm considering lane changes

Lane changes occur as many times as turning movements are needed while following a designated path. The cost of a route with many lane changes is likely to be more expensive than that with less lane changes, and unrealistic paths with impractical lane changes should be avoided for drivers' safety. In this regard, a new algorithm is developed in this study to find the realistic shortest path considering lane changing. The proposed algorithm is a modified link‐labeling Dijkstra algorithm considering the effective lane‐changing time that is a parametric function of the prevailing travel speed and traffic density. The parameters were estimated using microscopic traffic simulation data, and the numerical test demonstrated the performance of the proposed algorithm. It was found that the magnitude of the effect of the effective lane‐changing time on determining the realistic shortest path is nontrivial, and the proposed algorithm has capability to exclude links successfully where the required lane changes are practically impossible. Copyright © 2015 John Wiley & Sons, Ltd.     

Optimal location of advance warning for mandatory lane change near a two-lane highway off-ramp

Improper mandatory lane change (MLC) maneuvers in the vicinity of highway off-ramp will jeopardize traffic efficiency and safety. Providing an advance warning for lane change necessity is one of the efficient methods to perform systematic lane change management, which encourages smooth MLC maneuvers occurring at proper locations to mitigate the negative effects of MLC maneuvers on traffic flow nearby off-ramp. However, the state of the art indicates the lack of rigorous methods to optimally locate this advance warning so that the maximum benefit can be obtained. This research is motivated to address this gap. Specifically, the proposed approach considers that the area downstream of the advance warning includes two zones: (i) the green zone whose traffic ensures safe and smooth lane changes without speed deceleration (S-MLC); the start point of the green zone corresponding to the location of the advance warning; (ii) the yellow zone whose traffic leads to rush lane change maneuvers with speed deceleration (D-MLC). An optimization model is proposed to search for the optimal green and yellow zones. Traffic flow theory such as Greenshield model and shock wave analysis are used to analyze the impacts of the S-MLC and D-MLC maneuvers on the traffic delay. A grid search algorithm is applied to solve the optimization model. Numerical experiments conducted on the simulation model developed in Paramics 6.9.3 indicate that the proposed optimization model can identify the optimal location to set the advance MLC warning nearby an off-ramp so that the traffic delay resulting from lane change maneuvers is minimized, and the corresponding capacity drop and traffic oscillation can be efficiently mitigated. Moreover, the experiments validated the consistency of the green and yellow zones obtained in the simulation traffic flow and from the optimization model for a given optimally located MLC advance warning under various traffic regimes. The proposed approach can be implemented by roadside mobile warning facility or on-board GPS for human-driven vehicles, or embedded into lane change aid systems to serve connected and automated vehicles. Thus it will greatly contribute to both literature and engineering practice in lane change management.     

A Cooperative Intelligent Transport Systems (C‐ITS)‐based lane‐changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane‐change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane‐changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C‐ITS). This research investigates a lane‐change distribution advisory application based on C‐ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane‐changing concentration problem by coordinating weaving vehicles to ensure that such lane‐changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in aimsun to evaluate the proposed strategy's effectiveness in a one‐sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane‐changing advisory has the potential to significantly improve delay. Copyright © 2016 John Wiley & Sons, Ltd.     

Optimal starting location of an HOV lane for a linear monocentric urban area

This paper analyzes the optimal starting location of a high-occupancy-vehicle (HOV) lane for a linear monocentric urban area. Both travel time and carpooling costs are taken into account. The research proposes an analytical framework for the case with a continuum demand distribution along a highway corridor. The objective is assumed to maximize social welfare of the transportation system, which is the difference between the total user benefit and travel cost. Numerical analysis via simulation experiments was conducted to seek the existence of an optimal solution. Based on the results of a sensitivity analysis, we find a specific relationship between the carpooling cost and the optimal design of the starting point of an HOV lane.     

Characterization and comparison of traffic flow on reversible roadways

Reversible traffic operations have become an increasingly popular strategy for mitigating traffic congestion associated with the directionally unbalanced traffic flows that are a routine part of peak commute periods, planned special events, and emergency evacuations. It is interesting that despite its widespread and long‐term use, relatively little is known about the operational characteristics of this form of operation. For example, the capacity of a reversed lane has been estimated by some to be equal to that of a normal lane while others have theorized it to be half of this value. Without accurate estimates of reversible lane performance it is not possible to confidently gauge the benefits of reversible roadways or model them using traffic simulation. This paper presents the results of a study to measure and evaluate the speed and flow characteristics of reverse‐flow traffic streams by comparing them under various operating conditions and locations. It was found that, contrary to some opinions, the flow characteristics of reverse‐flowing lanes were generally similar to normally flowing lanes under a variety of traffic volume, time‐of‐day, location, and type‐of‐use conditions. The study also revealed that drivers will readily use reversible lanes without diminished operating speeds, particularly as volumes increase. Copyright © 2010 John Wiley & Sons, Ltd.     

Safety impacts of signalized lane merge control at highway work zones

Lane closures due to highway work zones present many challenges to the goal of ensuring smooth traffic operations and a safe environment for both drivers and workers. Late merge behavior at a work zone closure is a dangerous behavior that impacts the traffic conflicts upstream of work zone closures. This paper analyzes the safety impacts of using a signalized lane control strategy at the work zone merge points. To achieve the objective of this research, a field study has been conducted at a highway work zone to collect traffic and driver behavior data, and a two-stage, simulation-based approach is used to analyze the safety impacts of implementing a signalized lane merge control strategy at the studied work zone. In the first stage, micro-simulation models are developed and calibrated based on field data to generate vehicle trajectories. In the second stage, the U.S. Federal Highway Administration’s Surrogate Safety Assessment Model is employed to identify potential conflicts under different traffic conditions. The paper concludes that a proposed signal control device could significantly reduce lane-change conflicts at work zone merge points. In addition, recommendations on the signal cycle length and timing splits are provided.     

Impact of heavy vehicles on surrounding traffic characteristics

This work examines the impact of heavy vehicle movements on measured traffic characteristics in detail. Although the number of heavy vehicles within the traffic stream is only a small percentage, their impact is prominent. Heavy vehicles impose physical and psychological effects on surrounding traffic flow because of their length and size (physical) and acceleration/deceleration (operational) characteristics. The objective of this work is to investigate the differences in traffic characteristics in the vicinity of heavy vehicles and passenger cars. The analysis focuses on heavy traffic conditions (level of service E) using a trajectory data of highway I‐80 in California. The results show that larger front and rear space gaps exist for heavy vehicles compared with passenger cars. This may be because of the limitations in manoeuvrability of heavy vehicles and the safety concerns of the rear vehicle drivers, respectively. In addition, heavy vehicle drivers mainly keep a constant speed and do not change their speed frequently. This work also examines the impact of heavy vehicles on their surrounding traffic in terms of average travel time and number of lane changing manoeuvres using Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Networks (AIMSUN) microscopic traffic simulation package. According to the results, the average travel time increases when proportion of heavy vehicles rises in each lane. To reflect the impact of heavy vehicles on average travel time, a term related to heavy vehicle percentage is introduced into two different travel time equations, Bureau of Public Roads and Akçelik's travel time equations. The results show that using an exclusive term for heavy vehicles can better estimate the travel times for more than 10%. Finally, number of passenger car lane changing manoeuvres per lane will be more frequent when more heavy vehicles exist in that lane. The influence of heavy vehicles on the number of passenger car lane changing is intensified in higher traffic densities and higher percentage of heavy vehicles. Large numbers of lane changing manoeuvres can increase the number of traffic accidents and potentially reduce traffic safety. The results show an increase of 5% in the likelihood of accidents, when percentage of heavy vehicles increases to 30% of total traffic. Copyright © 2014 John Wiley & Sons, Ltd.     

A macroscopic traffic model for highway work zones: Formulations and numerical results

This study presents a multilane model for analyzing the dynamic traffic properties of a highway segment under a lane‐closure operation that often incurs complex interactions between mandatory lane‐changing vehicles and traffic at unblocked lanes. The proposed traffic flow formulations employ the hyperbolic model used in the non‐Newtonian fluid dynamics, and assume the lane‐changing intensity between neighboring lanes as a function of their difference in density. The results of extensive simulation experiments indicate that the proposed model is capable of realistically replicating the impacts of lane‐changing maneuvers from the blocked lanes on the overall traffic conditions, including the interrelations between the approaching flow density, the resulting congestion level, and the exiting flow rate from the lane‐closure zone. Our extensive experimental analyses also confirm that traffic conditions will deteriorate dramatically and evolve to the state of traffic jam if the density has exceeded its critical level that varies with the type of lane‐closure operations. This study also provides a convenient way for computing such a critical density under various lane‐closure conditions, and offers a theoretical basis for understanding the formation as well as dissipation of traffic jam.     

The optimization of lane assignment and signal timing at the tandem intersection with pre‐signal

This paper presents an integrated model for optimizing lane assignment and signal timing at tandem intersection, which is introduced recently. The pre‐signal is utilized in the tandem intersection to reorganize the traffic flow; hence, the vehicles, regardless of whether left‐turns or through vehicles, can be discharged in all the lanes. However, the previous work does not consider the extra traffic disruption and the associated delay caused by the additional pre‐signal. In the paper, the extra delay aroused by the coordination is incorporated in a lane assignment and signal timing optimization model, and the problem is converted into a mixed‐integer non‐linear programming. A feasible directions method is hence introduced to solve the mixed‐integer non‐linear programming. The result of the optimization shows that the performance of the tandem intersection is improved and the average delay is minimized. The comparison between the tandem and the conventional configuration is presented, and the results verify that the former shows better performance than the latter. In addition, the optimal sequence corresponding to the turning proportion and the optimal lane assignment at the upstream approach of the pre‐signal are presented. Furthermore, if the number of lanes is equal in all arms, the paper proves that the average delay will be reduced if lane assignment is proportional to the turning proportion and the vehicles with low proportion are discharged in advance. Copyright © 2013 John Wiley & Sons, Ltd.     

Modeling delay at signalized intersections with channelized right‐turn lanes considering the impact of blockage

This paper presents a probabilistic delay model for signalized intersections with right‐turn channelization lanes considering the possibility of blockage. Right‐turn channelization is used to improve the capacity and to reduce delay at busy intersections with a lot of right‐turns. However, under heavy traffic conditions the through vehicles will likely block the channelization entrance that accrues delay to right‐turn vehicles. If the right‐turn channelization gets blocked frequently, its advantage in reducing the intersection delay is neglected and as a result the channelization lane becomes inefficient and redundant. The Highway Capacity Manual (HCM) neglects the blockage effect, which may be a reason for low efficiency during peak hours. More importantly, using HCM or other standard traffic control methods without considering the blockage effects would lead to underestimation of the delay. To overcome this issue, the authors proposed delay models by taking into account both deterministic and random aspects of vehicles arrival patterns at signalized intersections. The proposed delay model was validated through VISSIM, a microscopic simulation model. The results showed that the proposed model is very precise and accurately estimates the delay. In addition, it was found that the length of short‐lane section and proportion of right‐turn and through traffic significantly influence the approach delay. For operational purposes, the authors provided a step‐by‐step delay calculation process and presented approach delay estimates for different sets of traffic volumes, signal settings, and short‐lane section lengths. The delay estimates would be useful in evaluating adequacy of the current lengths, identifying the options of extending the short‐lane section length, or changing signal timing to reduce the likelihood of blockage. Copyright © 2016 John Wiley & Sons, Ltd.     

Optimal subwork zone operational strategy for short‐term work zone projects in four‐lane two‐way freeways

Roadside trees in Singapore are regularly trimmed for the purpose of traffic safety and roadside tree‐trimming project is one typical type of short‐term work zone projects. To implement such a short‐term work zone project, contractors usually divide an entire work zone into multiple subwork zones with the uniform length. This paper aims to determine an optimal subwork zone strategy for the short‐term work zone projects in four‐lane two‐way freeways with time window and uniform subwork zone length constraints. The deterministic queuing model is employed to estimate total user delay caused by the work zone project by taking into account variable traffic speeds. Based on the user delay estimations, this paper proceeds to build a minimization model subject to time window and uniform length constraints for the optimal subwork zone strategy problem. This paper also presents a variation of the minimization model to examine the impact of unequal subwork zone length constraint. Since these minimization models belong to the mixed‐integer non‐differentiable optimization problems, an iterative algorithm embedding with the genetic simulated annealing method is thus proposed to solve these models. Finally, a numerical example is carried out to investigate the effectiveness of the proposed models. Copyright © 2010 John Wiley & Sons, Ltd.     

Impact of stop-and-go waves and lane changes on discharge rate in recovery flow

In an effort to uncover traffic conditions that trigger discharge rate reductions near active bottlenecks, this paper analyzed individual vehicle trajectories at a microscopic level and documented the findings. Based on an investigation of traffic flow involving diverse traffic situations, a driver’s tendency to take a significant headway after passing stop-and-go waves was identified as one of the influencing factors for discharge rate reduction. Conversely, the pattern of lane changers caused a transient increase in the discharge rate until the situation was relaxed after completing the lane-changing event. Although we observed a high flow from the incoming lane changers, the events ultimately caused adverse impacts on the traffic such that the disturbances generated stop-and-go waves. Based on this observation, we regard upstream lane changes and stop-and-go waves as the responsible factors for the decreased capacity at downstream of active bottlenecks. This empirical investigation also supports the resignation effect, the regressive effect, and the asymmetric behavioral models in differentiating acceleration and deceleration behaviors.     

A network enhancement model with integrated lane reorganization and traffic control strategies

Lane reorganization strategies such as lane reversal, one‐way street, turning restriction, and cross elimination have demonstrated their effectiveness in enhancing transportation network capacity. However, how to select the most appropriate combination of those strategies in a network remains challenging to transportation professionals considering the complex interactions among those strategies and their impacts on conventional traffic control components. This article contributes to developing a mathematical model for a traffic equilibrium network, in which optimization of lane reorganization and traffic control strategies are integrated in a unified framework. The model features a bi‐level structure with the upper‐level model describing the decision of the transportation authorities for maximizing the network capacity. A variational inequality (VI) formulation of the user equilibrium (UE) behavior in choosing routes in response to various strategies is developed in the lower level. A genetic algorithm (GA) based heuristic is used to yield meta‐optimal solutions to the model. Results from extensive numerical analyses reveal the promising property of the proposed model in enhancing network capacity and reducing congestion. Copyright © 2016 John Wiley & Sons, Ltd.     

Queuing simulation of roadside survey station: Blocked traffic lane

External station travel surveys provide critical inputs to travel demand models. The results from these models are frequently used for statewide planning purposes. Although a roadside survey is very effective in obtaining useful information from road users, its major drawback is the excessive delay that is imposed onto road users particularly on high-volume facilities. In this paper, we used a discrete event simulation to model a blocked traffic lane survey, which is usually conducted for two-lane undivided highways. This type of survey station requires a complete stop of all oncoming traffic. Non-surveyed traffic has no ability to go around and thus has to wait in a queue in order to proceed through the survey station. Road users’ impacts are quantified in terms of delay and queue length while the performance of surveyors is measured by the number of surveys completed per unit time. Sensitivity analyses of simulation inputs reveal that simulation results are fairly insensitive to selected parameters. The results in this study provide a quick and useful guideline that roadside surveyors can use to estimate the road user impacts prior to the survey and to plan the survey procedure accordingly.     

Operation of signalized diamond interchanges with frontage roads using dynamic reversible lane control

Signalized diamond interchanges (SDI), connecting major highways and surface streets in urban and suburban areas, are probably the most widely used interchange patterns. The limited storage space between the two closely joined intersections coupled with heavy traffic volumes may easily oversaturate the facility and cause spillback problems, especially with the presence of frontage roads. This paper presents an innovative design and operational model for SDI by dynamically reversing certain lanes in the internal link on a regular basis with the deployment of overhead reversible lane control signs. A Binary-Mixed-Integer-Linear-Program (BMILP) is formulated to simultaneously optimize lane markings, dynamic usage of the reversible lane, and signal timings for the new SDI system. Results from extensive numerical analyses reveal the promising property of the proposed design and operational model in expanding capacity and reducing congestion at the SDI with frontage roads.     

Evaluating the effects of automated vehicle technology on the capacity of freeway weaving sections

Weaving sections, where a merge and a diverge are in close proximity, are considered as crucial bottlenecks in the highway network. Lane changes happen frequently in such sections, leading to a reduced capacity and the traffic phenomenon known as capacity drop. This paper studies how the emerging automated vehicle technology can improve the operations and increase the capacity of weaving sections. We propose an efficient yet effective multiclass hybrid model that considers two aspects of this technology in scenarios with various penetration rates: (i) the potential to control the desired lane change decisions of automated vehicles, which is represented in a macroscopic manner as the distribution of lane change positions, and (ii) the lower reaction time associated with automated vehicles that can reduce headways and the required gaps for lane changing maneuvers. The proposed model is successfully calibrated and validated with empirical observations from conventional vehicles at a weaving section near the city of Basel, Switzerland. It is able to replicate traffic dynamics in weaving sections including the capacity drop. This model is then applied in a simulation-based optimization framework that searches for the optimal distribution of the desired lane change positions to maximize the capacity of weaving sections. Simulation results show that by optimizing the distribution of the desired lane change positions, the capacity of the studied weaving section can increase up to 15%. The results also indicate that if the reaction time is considered as well, there is an additional combined effect that can further increase the capacity. Overall, the results show the great potential of the automated vehicle technology for increasing the capacity of weaving sections.     

Design and evaluation of an automated highway system with optimized lane assignment

Highway automation entails the application of control, sensing and communication technologies to road vehicles, with the objective of improving highway performance. It has been envisioned that automation could increase highway capacity by a factor of three. The purpose of this paper is to develop a methodology for predicting highway capacity and comparing alternative automation concepts. It extends earlier research on optimal lane assignment on an automated highway to dynamic networks. A path-based linear program is formulated and solved through a column generation method. The algorithm has been applied to networks with as many as 20 on and off ramps, 80 segments, 4 lanes and 12 time periods.     

Categorization of the lane change decision process on freeways

Traffic operations for new road layouts are often simulated using microscopic traffic simulation packages. These traffic simulation packages usually simulate traffic on freeways by a combination of a car-following model and a lane change model. The car-following models have gained attention of researchers and are well calibrated versus data. The proposed lane change models are often representations of assumed reasonable behavior, not necessarily corresponding to reality. The current simulation packages apply solely one specific type of model for car-following or lane changing for all vehicles during the simulation. This paper investigates the decision process of lane changing maneuvers for a variety of drivers based on a two-stage test-drive. Participants are asked to take a drive on a freeway in the Netherlands in a camera-equipped vehicle. Afterwards, the drivers are asked to comment on their choices related to lane and speed choice, while watching the video. This paper reveals that different drivers have completely different strategies to choose lanes, and the choices to change lane are related to their speed choice. Four distinct strategies are empirically found. These strategies differ not only in parameter values, as is currently being modeled in most simulation packages, but also in their reasoning. Most remarkably, all drivers perceive their strategy as an obvious behavior and expect all other drivers to drive in a similar way. In addition to the interviews of the participants in the test-drive, 11 people who did not take part in the experiment were interviewed and questioned on lane change decisions. Moreover, the findings of this study have been presented to various groups of audience with different backgrounds (about 150 people). Their comments and feedback on the derived driving strategies have added some value to this study. The findings in this paper form a starting point for developing a novel lane change model which considers four different driving strategies among the drivers on freeway. This is a significant contribution in the area of driving behavior modeling, since the existing microscopic simulators consider only one type of lane change models for all drivers during the simulation. This could lead to significant changes in the way lane changes on freeways are modeled.